• Journal of Sensor Science and Technology
• /
• v.23 no.2
• /
• pp.134-141
• /
• 2014

A stoichiometric mixture of evaporating materials for $BaIn_2Se_4$ epilayers was prepared from horizontal electric furnace. To obtain the single crystal thin films, $BaIn_2Se_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperatures were $620^{\circ}C$ and $400^{\circ}C$, respectively. The crystalline structure of the epilayers was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $BaIn_2Se_4$ epilayers measured from Hall effect by van der Pauw method are $8.94{\times}10^{17}cm^{-3}$ and 343 $cm^2/vs$ at 293 K, respectively. The temperature dependence of the energy band gap of the $BaIn_2Se_4$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)$=2.6261 eV-$(4.9825{\times}10^{-3}eV/K)T^2/(T+558 K)$. The crystal field and the spin-orbit splitting energies for the valence band of the $BaIn_2Se_4$ have been estimated to be 116 meV and 175.9 meV, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the ${\Delta}so$ definitely exists in the ${\Gamma}_5$ states of the valence band of the $BaIn_2Se_4/GaAs$ epilayer. The three photocurrent peaks observed at 10 K are ascribed to the $A_1-$, $B_1$-exciton for n = 1 and $C_{21}$-exciton peaks for n=21.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.857-864
• /
• 2011

Oxy-fuel combustion with many advantages such as high combustion efficiency, low flue gas flow rate and low NOx emission has emerged as a promising CCS technology for coal combustion facilities. In this study, the effects of the direct sulfation reaction on $SO_2$ removal efficiency were evaluated in a drop tube furnace under typical oxy-fuel combustion conditions represented by high concentrations of $CO_2$ and $SO_2$ formed by gas recirculation to control furnace combustion temperature. The effects of the operating parameters including the reaction temperature, $CO_2$ concentration, $SO_2$ concentration, Ca/S ratio and humidity on $SO_2$ removal efficiency were investigated experimentally. $SO_2$ removal efficiency increased with reaction temperature up to 1,200 due to promoted calcination of limestone reagent particles. And $SO_2$ removal efficiency increased with $SO_2$ concentrations and the humidity of the bulk gas. The increase of $SO_2$ removal efficiency with $CO_2$ concentrations showed that $SO_2$ removal by limestone was mainly done by the direct sulfation reaction under oxy-fuel combustion conditions. From the impact assessment of operation parameters, it was shown that these parameters have an effects on the desulfurization reaction by the order of the Ca/S ratio > residence time > $O_2$ concentration > reaction temperature > $SO_2$ concentration > $CO_2$ concentration > water vapor. The semi-empirical model equation for to evaluate the effect of the operating parameters on the performance of in-furnace desulfurization for oxy-fuel combustion was established.

• Journal of Sensor Science and Technology
• /
• v.24 no.6
• /
• pp.404-411
• /
• 2015

A stoichiometric mixture of evaporating materials for $BaAl_2Se_4$ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films, $BaAl_2Se_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperatures were $610^{\circ}C$ and $410^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $BaAl_2Se_4$ single crystal thin films measured from Hall effect by van der Pauw method are $8.29{\times}10^{-16}cm^{-3}$ and $278cm^2/vs$ at 293 K, respectively. The temperature dependence of the energy band gap of the $BaAl_2Se_4$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)=3.4205eV-(4.3112{\times}10^{-4}eV/K)T^2/(T+232 K)$. The crystal field and the spin-orbit splitting energies for the valence band of the $BaAl_2Se_4$ have been estimated to be 249.4 meV and 263.4 meV, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the ${\Delta}so$ definitely exists in the ${\Gamma}_5$ states of the valence band of the $BaAl_2Se_4/GaAs$ epilayer. The three photocurrent peaks observed at 10 K are ascribed to the $A_1$-, $B_1$-exciton for n =1 and $C_{31}$-exciton peaks for n=31.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.1
• /
• pp.18-24
• /
• 2019

This study was carried out to investigate the effect of milling of boron (B), which is one of raw materials of $MgB_2$, on the critical current density ($J_c$) of $MgB_2$. B powder used in this study is semi-amorphous B (Pavezyum, Turkey, 97% purity, 1 micron). The size of B powder was reduced by planetary milling using $ZrO_2$ balls (a diameter of 2 mm). The B powder and balls with a ratio of 1:20 were charged in a ceramic jar and then the jar was filled with toluene. The milling time was varied from 0 to 8 h. The milled B powders were mixed with Mg powder in the composition of (Mg+2B), and the powder mixtures were uniaxially pressed at 3 tons. The powder compacts were heat-treated at $700^{\circ}C$ for 1 h in flowing argon gas. Powder X-ray diffraction and FWHM (Full width at half maximum) were used to analyze the phase formation and crystallinity of $MgB_2$. The superconducting transition temperature ($T_c$) and $J_c$ of $MgB_2$ were measured using a magnetic property measurement system (MPMS). It was found that $B_2O_3$ was formed by B milling and the subsequent drying process, and the volume fraction of $B_2O_3$ increased as milling time increased. The $T_c$ of $MgB_2$ decreased with increasing milling time, which was explained in terms of the decreased volume fraction of $MgB_2$, the line broadening of $MgB_2$ peaks and the formation of $B_2O_3$. The $J_c$ at 5 K increased with increasing milling time. The $J_c$ increase is more remarkable at the magnetic field higher than 3 T. The $J_c$ at 5 K and 4 T was the highest as $4.37{\times}10^4A/cm^2$ when milling time was 2 h. The $J_c$ at 20 K also increased with increasing milling time. However, The $J_c$ of the samples with the prolonged milling for 6 and 8 h were lower than that of the non-milled sample.

• Korean Journal of Agricultural Science
• /
• v.12 no.1
• /
• pp.47-54
• /
• 1985

An investigation was made to find regional differences and seed characteristics of buckwheats collected from 36 areas in Chungnam province in 1984, and the results obtained are summarized as follows; 1. Grain types of the collected buckwheats were classified as winged, semi-winged and common types. All collections were on the average composed of 50.1 % of common grain types, 26.8 % of semi-winged type and 23.1 % of winged types, respectively. However, there was a great regional difference in components of each grain type among collections. 2. The mean 1000 grain weight was 24.9 gr. The regional differences in 1000 grain weight showed that a collection (collection no. 30) from Susan was 17.4 gr and a collection (collection. no. 16) from Suchon was 31.9 gr. There wasn't any significant relationship between grain types component and 1000 grain weight. 3. Germination of seeds was accelerated as temperature goes up from $5^{\circ}C$ to $30^{\circ}C$. However, interesting germination pattern was observed. That is, seeds from Suchon (collection no. 16), Hongsung (collection no. 23), Cheonweon(collection no. 35), and Yesan (collection no. 27) showed abrupt decrease of germination rate at the temperature of $15^{\circ}C$. The seeds collected from Suchon (collection no. 29), Dangjin (collection no. 32) and from Chungyang (collection no. 21) showed decrease of germination rate at $25^{\circ}C$. These seeds showed, however, the increase of germination percentage at temperature higher than $15^{\circ}C$ and $25^{\circ}C$, respectively. The germination rate for the most collections at $5^{\circ}C$ was less than 10%. However, seeds from Asan (collection no. 33) and Daeduk (collection no. 3) showed 20% and 30% of germination rate at $5^{\circ}C$, respectively. 4. Color of seed coat could be classified into two maj or colors, dark and dark brown. Based on the seed coat color and grain types, all the collections could be classified into the following six categories: winged-black, semi-winged-black, common-black, winged-dark brown, semi-winged dark brown and common-dark brown. The different light absorption rate was found within the UV light zone (190-390 nm) depending upon the two different major seed coat color.

• Journal of Bio-Environment Control
• /
• v.31 no.3
• /
• pp.221-229
• /
• 2022

This study was aimed to investigate spatial and vertical characteristics of greenhouse environments according to the location of the environmental sensors, and to investigate the correlations between temperature, light intensity, and carbon dioxide (CO₂) concentration according to the type of greenhouse. Temperature, relative humidity (RH), CO₂, and light sensors were installed in the four-different vertical positions of the whole canopy as well as ground and roof space at the five spatial locations of the Venlo greenhouse. Also, correlations between temperature, light intensity, and CO₂ concentration in Venlo and semi-closed greenhouses were analyzed using the Curve Expert Professional program. The deviations among the spatial locations were larger in the CO₂ concentration than other environmental factors in the Venlo greenhouse. The average CO₂ concentration ranged from 465 to 761 µmol·mol^-1 with the highest value (646 µmol·mol^-1) at the Middle End (4ME) close to the main pipe (50Ø) of the liquefied CO₂ gas supply and lowest (436 µmol·mol^-1) at the Left Middle (5LM). The deviation among the vertical positions was greater in temperature and relative humidity than other environments. The time zone with the largest deviation in average temperature was 2 p.m. with the highest temperature (26.51℃) at the Upper Air (UA) and the lowest temperature (25.62℃) at the Lower Canopy (LC). The time zone with the largest deviation in average RH was 1 p.m. with the highest RH (76.90%) at the LC and the lowest RH (71.74%) at the UA. The highest average CO₂ concentration at each hour was Roof Air (RF) and Ground (GD). The coefficient of correlations between temperature, light intensity, and CO₂ concentration were 0.07 for semi-closed greenhouse and 0.66 for Venlo greenhouse. All the results indicate that while the CO₂ concentration in the greenhouse needs to be analyzed in the spatial locations, temperature and humidity needs to be analyzed in the vertical positions of canopy. The target CO₂ fertilization concentration for the semi-closed greenhouse with low ventilation rate should be different from that of general greenhouses.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.6
• /
• pp.244-252
• /
• 2004

A stoichiometric mixture of evaporating materials for $CuInSe_2$ single crystal thin films was prepared from horizontal electric furnace. To obtain the single crystal thin films, $_CuInSe2$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (HWE) system. The source and substrate temperatures were $620^{\circ}C$ and $410^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $CuInSe_2$ single crystal thin films measured with Hall effect by van der Pauw method are $9.62\times10^{16}/\textrm{cm}^3$, 296 $\textrm{cm}^2$/Vㆍs at 293 K, respectively. The temperature dependence of the energy band gap of the $CuInSe_2$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g$(T) = 1.1851 eV -($8.99\times10^{-4} eV/K)T^2$(T + 153 K). The crystal field and the spin-orbit splitting energies for the valence band of the CuInSe$_2$ have been estimated to be 0.0087 eV and 0.2329 eV at 10 K, respectively, by means of the photocurrent spectra and the Hopfield quasicubic model. These results indicate that the splitting of the Δso definitely exists in the $\Gamma$6 states of the valence band of the $CuInSe_2$. The three photocurrent peaks observed at 10 K are ascribed to the $A_1-, B_1$-와 $C_1$-exciton peaks for n = 1.

• Korean Journal of Environment and Ecology
• /
• v.26 no.3
• /
• pp.313-321
• /
• 2012

To analyze the bird communities by the land use type, we surveyed 43 plots in Siheung City, Korea from Mar. 2009 to Feb. 2010 and classified the community by TWINSPAN and DCA. Classification result by TWINSPAN was classified into 4 communities. In the first division, waterbirds, such as spot-billed duck(Anas poecilorhyncha) and great egret(Egretta alba) operated as the differential species. In the second and third division, little grebe(Tachybaptus ruficollis) and eurasian sparrow(Passer montanus) were operated as the differential species. The relationship between land use types and classified bird communities, all plots of community I were located in the forest. Community II plots were contained all urban and several semi-natural land use types. Community III contains stream and rice paddy. Plots in the reservoir were classified community IV. The stream and rice paddy were classified into different communities, which were colsely related with the size of wetland paddy. Community III had the highest species diversity index and community II had lowest. Community III also had the highest maximum species diversity index and evenness index. The result of this study, small stream and small rice paddy located within the city have insignificant characteristics as the habitat for birds. Management size of semi-natural land use for wildbird habitat in the urban area should be considered for showing their habitat characteristics. If the classification of biotope type based on the scale of rice paddy and urban park and the type of landuse type in the riverside then we should be consider the standard of minium area.

• Analytical Science and Technology
• /
• v.11 no.2
• /
• pp.112-119
• /
• 1998

A Siemens SemiQuant (SSQ) 3000 program, a precalibrated 'standardless' analytical program handling up to 90 elements, was evaluated for the fast analysis of various types of reference materials using a wavelength dispersive X-ray spectrometer. Various types of standard reference materials such as metal discs, metal chips, and geological materials in powder form were analysed and it took 23 minutes of measuring time for 75 elements. Measurements of geological reference materials using different sampling methods were carried out and their data were interactively evaluated. The analysis of materials of a known matrix concentration such as stainless steels provided higher precision value compared to totally unknown samples. The analyses of materials prepared as pressed pellets or fused glass beads provided higher precision values compared to the measurement of loose powders with a foil on the sample surface and helium operation, though their sampling procedures were more complicate and took more time. Since very light elements such as boron, carbon, and oxygen have a strong influence on the matrix effects and also on the calculation of effective matrix corrections, the rhodium Compton check was applied to verify the reliability of the defined light element concentrations of light matrix materials and the defined major sample compounds. Failure of defining correct matrix resulted in an unoptimized matrix correction and therefore in the wrong calculation of the element concentration.

• Development and Reproduction
• /
• v.15 no.3
• /
• pp.265-272
• /
• 2011

It is well known that adipose tissue or body fat has been proved as a crucial component of brain-peripheral axis which can modulate the activities of reproductive hormonal axis in female mammals including rodents and human. Concerning the male reproduction, however, the role of adipose tissue has not been thoroughly studied. The present study was carried out to elucidate the effect of a high-fat (HF) diet on the reproductive system of postpubertal male rats. The HF diet (45% energy from fat, HF group) was applied to male rats from week 8 after birth for 4 weeks. The blood glucose levels, body and tissue weights were measured. Histological studies were performed to assess the structural alterations in the reproductive tissues. To determine the transcriptional changes of reproductive hormone-related genes in hypothalamus and pituitary, total RNAs were extracted and applied to the semi-quantitative reverse transcription polymerase chain reaction (RT-PCR). Body weights (p<0.01) and blood glucose levels (p<0.01) of HF group were significantly higher than those of control animals. Similarly, the weights of epididymis (p<0.05), prostate (p<0.01), seminal vesicle (p<0.01) in HF group were higher than control levels. The weights of testis were not changed. The weights of kidney (p<0.001) and spleen (p<0.01) were significantly higher than control levels while the adrenal and pancreas weights were not changed. There were only slight alterations in the microstructures of accessory sex organs; the shape of luminal epithelial cells in epididymis from HF group were relatively thicker and bigger than those from control animals. In the semi-quantitative RT-PCR studies, the mRNA levels of hypothalamic GnRH (p<0.05) in HF group were significantly higher than those from the control animals. The mRNA levels of kisspeptin in HF group tend to be higher than control levels, the difference was not significant. Unlike the hypothalamic GnRH expression, the mRNA levels of pituitary $LH{\beta}$ and $FSH{\beta}$ were significantly decreased in HF group (p<0.05). The present study indicated that the 4-weeks feeding HF diet during the postpubertal period can alter the hypothalamus-pituitary (H-P) neuroendocrine reproductive system These results suggest that the increased body fat and the altered leptin input might disturb the H-P reproductive hormonal activities in male rats, and the changed activities seem to be responsible for the changes of tissue weights in accessory sex organs.