• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.4
• /
• pp.492-498
• /
• 2017

In this paper, we integrate a divide-by-3 injection-locked frequency divider (ILFD) in CMOS technology with a $0.18-{\mu}m$ BiCMOS process. We propose a self-injection technique that utilizes harmonic conversion to improve the locking range, phase-noise, and input sensitivity simultaneously. The proposed self-injection technique consists of an odd-to-even harmonic converter and a feedback amplifier. This technique offers the advantage of increasing the injection efficiency at even harmonics and thus realizes the low-power implementation of an odd-order division ILFD. The measurement results using the proposed self-injection technique show that the locking range is increased by 47.8% and the phase noise is reduced by 14.7 dBc/Hz at 1-MHz offset frequency with the injection power of -12 dBm. The designed divide-by-3 ILFD occupies $0.048mm^2$ with a power consumption of 18.2-mW from a 1.8-V power supply.

• Journal of Oral Medicine and Pain
• /
• v.42 no.2
• /
• pp.29-34
• /
• 2017

Purpose: To evaluate aggravating factors of intermittent locking among temporomandibular joint using magnetic resonance imaging (MRI) and diagnostic criteria for temporomandibular disorder (DC/TMD) diagnosis. Methods: A retrospective analysis was conducted of 35 patients with intermittent locking history but normal intra-articular findings between September 2012 and June 2015 in Kyung Hee University Dental Hospital. A standardized DC/TMD assessment was performed on subjects with MRI findings. Clinical findings were assessed on the basis of maximum mouth opening (active & passive), self-reported habits, patients' age, gender, systemic diseases at the initial visit. First, chi square test was used to examine differences with variables and then risk factors for intermittent locking were assessed using multivariate logistic regression. Results: Self-reported bruxism was strongly associated with intermittent locking history. Conclusions: The new DC/TMD protocol is intended for use within any clinical setting and supports the full range of diagnostic activities from screening to definitive evaluation and diagnosis. Self-reported sleep bruxism has been associated with a higher likelihood of intermittent locking. Comorbidity is therefore a factor that must be assessed. It is necessary to consider the amount of contact of the teeth and the duration.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.1 no.3
• /
• pp.193-196
• /
• 2001

For wide locking range, an analog delay locked loop (DLL) was designed with the selective phase inversion scheme and the variable number of delay elements. The number of delay elements was determined adaptively depending on the clock cycle time. During the analog fine locking stage, a self-initializing 3-state phase detector was used to avoid the initial state problem associated with the conventional 3-state phase detector. With these schemes, the locking range of analog DLL was increased by four times compared to the conventional scheme according to the simulation results.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.655-661
• /
• 2007

A new steel connection method using wedges known as Self-Locking Connector has been developed. In this study, experimental investigation was conducted to verify the seismic performance of steel beam-to-column joints with Self-Locking Connectors. Cyclic-loading tests were performed on two beam-to-column joints with Self-Locking Connectors. The two beam-to-column joint specimens were of the cantilever-type and had the same details. Test results showed that beam-to-column joints with Self-Locking Connectors were able to developa total rotation capacity of 0.06 radian, which is greater than the 0.04 radian required for Special Moment Frames. Moreover, their energy absorption capacity was much greater than that of conventional joints.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1696-1699
• /
• 1997

The robot mainpulator for inspection of pressurizer in the nuclear power plant has been developed, which consists of four parts : 2 arms, movable gripper, base frame, contorl console. To extract the damaged electric heating rod inside pressurizer, the gripper has been developed using wire lope and self-locking mechanism. for the examination of the structural stability of the robot manipulator, stress analysis is performed by using the ANSYS code.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.11a
• /
• pp.412-412
• /
• 2004

• Steel and Composite Structures
• /
• v.48 no.5
• /
• pp.599-610
• /
• 2023

To avoid debonding failure, a novel type of hybrid anchorage (HA) is proposed in this study that uses a slotted plate to lock the ends of the fiber-reinforced polymer (FRP) sheet in addition to the usual bonding over the substrate of the strengthened member. An experimental investigation was performed on three groups of RC beams, which differed from one another in either concrete strength or steel reinforcement ratio. The test results indicate that the end self-locking of the CFRP sheet can improve the failure ductility, ultimate capacity of the beams and its utilization ratio. Although intermediate debonding occurred in all the strengthened beams, it was not a fatal mode of failure for the three specimens with end anchorage. Among them, FRP rupture occurred in the beam with higher concrete strength and lower steel reinforcement ratio, whereas the other two failed by concrete crushing. The beam strengthened by HA obtained a relatively high percentage of increase in ultimate capacity when the rebar ratio or concrete strength decreased. The expressions in the literature were inspected to calculate the critical loads at intermediate debonding, FRP rupturing and concrete crushing after debonding for the strengthened beam. Then, the necessity of further research is addressed.

• Korean Journal of Optics and Photonics
• /
• v.5 no.4
• /
• pp.466-472
• /
• 1994

An Argon laser pumped Ti:Sapphire laser has been constructed and self-mode locked. Mode-locking was initiated by a moving mirror mounted on the ball slider and maintained by the self-focusing in the laser crystal and an aperture inside the resonator. A prism pair was used to reduce group velocity dispersion. The bandwidth and the pulse width of the mode-locked pulse were 11 nm, $1000\pm20fs$, respectively. ively.

• Korean Journal of Optics and Photonics
• /
• v.4 no.3
• /
• pp.330-337
• /
• 1993

Figure '8' type, passively-mode-locked erbium-doped-fiber ring laser was developed, incorporating a nonlinear loop mirror. Transmittance of the loop mirror was found to be dependent on the incident light intensity due to the non-reciprocal nonlinear phase shift, which enables the passive mode locking of the laser. Self-starting of stable mode locking was possible with only controlling the polarization controllers inside the cavity without any help of external perturbation or modulation. The mode-locked output pulse shape was discussed in relation with the transmission characteristics of nonlinear loop mirror.

• Journal of the Optical Society of Korea
• /
• v.15 no.1
• /
• pp.56-60
• /
• 2011

We demonstrate passive mode-locking of a Cr:forsterite laser with a single-walled carbon nanotube saturable absorber mirror (SWCNT-SAM). Without compensation of intra-cavity dispersion, the self-mode-locked laser generates 11.7 ps pulses at a repetition rate of 86 MHz. The dispersion-compensated laser yields ultrashort pulses as short as 80 fs near $1.25\;{\mu}m$ at 78 MHz with average output powers up to 295 mW, representing the highest power ever reported for mode-locked solid-state lasers based on saturable absorption of SWCNTs in this spectral region.