• 전기학회논문지
• /
• 제65권1호
• /
• pp.65-72
• /
• 2016

This paper presents the analysis of the analysis of thrust characteristics of linear induction motors(LIMs) according to secondary reaction plate. LIMs are well known as high speed transport systems, which can obtain thrust directly without gears and links, or auxiliary mechanisms. A simple structure, easy maintenance, and less environmental pollution are advantages of LIMs. In transport systems using LIMs, the secondary reaction plate is an important design factor, because it has considerable impact on the cost of the railway as well as the performance of the LIMs. This paper deals analyzed the characteristics of linear induction motor used for moving the vehicle of container scanner. Thrust, efficiency and load characteristic were interpreted with FEM regarding two models whose material of secondary reaction plate was copper and aluminum. It suggested the interpretation of thrust, efficiency and power factor characteristic along slip and compared the operation ability of linear induction motor through characteristics analysis along the load.

• 상하수도학회지
• /
• 제25권3호
• /
• pp.335-342
• /
• 2011

Secondary effluent contains particle compounds which are comprised of microorganisms that occurs membrane fouling when the water is reused. This study evaluates the characteristics of membrane fouling of secondary effluent reuse. Effects of chemical backwashing are analyzed to reduce membrane fouling by regular chemical backwashing. As the result, major membrane foulants are verified EPS materials which include protein and polysaccharide that cause biofilm cake layer on the membrane. Also, sodium hypochlorite is applied to chemical backwashing. The backwashing improves recover rate when injected chemical concentration is increased and chemical backwashing cycle is amplified. Chemical backwashing cycle affects more than injected chemical concentration yet idle time does not noticeably influence on reducing membrane fouling.

• 한국과학교육학회지
• /
• 제24권1호
• /
• pp.48-62
• /
• 2004

This research aimed to investigate whether Korean education programs for secondary science teachers reflect constructivist perspectives. To identify how to introduce the idea of constructivism and STS into the courses of the current Korean education programs for secondary science teachers, two programs were selected: the Qualifying In-service Program held in Seoul and the pre-service programs established in the four departments of science education of the Korean National University of Education in Chungbuk. The course guidebooks, syllabi, and text materials prepared for implementation of the courses were collected and analyzed. E-mail correspondence with the program instructors who had conveyed both ideas to the trainees provided us more precise information about the characteristics of the classes, such as the total time provided the ideas and the teaching strategies used to implement the classes. The results indicated that the pre-service programs included the ideas of constructivism and STS more than did the Qualifying In-service Program. It is necessary that the courses included in the Korean in-service program, in particular the Qualifying In-service Program for secondary science teachers, have to be more focused on the constructivist perspectives.

• 한국환경교육학회지:환경교육
• /
• 제2권1호
• /
• pp.5-33
• /
• 1991

The purpose of the study was to investigate attitudes toward to, values and expectations of environmental education of Korean students and teachers and to provide basic data and reference materials needed to development of environmental education curricula for primary and secondary schools. A review of the related literature, a series of conferences with teachers and specialists in environmental education and environmental sciences. and questionnaire survey were methods employed in this study. Survey question were developed to explore attitude and responses of primary and secondary school students and teachers on various types of issues and problems of environmental education at personal level as well as on their future prospects attitudes values and expectations with which had been dealt in this study were categorized into personal feeling on environmental issues and problems at both national and regional levels issues and problems of current environmental education pre service and in service training of teachers for environmental education instruction and so on. The sample population for the survey was selected by using the stratified cluster and random sampling techniques with respect to regional area, school level, sex and grade, The subjects used in this study were 1,633 students and 385 teachers of primary and secondary schools across the country. The results of the survey were summed up and recommendations to be considered in the revision of sixth national curricula for primary and secondary schools were also suggested.

• 자원리싸이클링
• /
• 제27권6호
• /
• pp.3-10
• /
• 2018

텅스텐은 고융점금속으로 주로 초경합금으로 사용되고 있다. 알칼리용액에서 텅스텐은 $WO{_4}^{2-}$로 존재하는데 용액의 pH가 감소함에 따라 중합반응이 일어나며 텅스텐산으로 침전된다. 따라서 원광석 및 2차 자원으로부터 텅스텐 회수를 위한 습식 제련 기술은 산침출과 알칼리침출로 대별된다. 2차 자원에 함유된 금속의 종류와 함유량 및 텅스텐의 소재화를 고려해서 2차 자원으로부터 텅스텐을 고순도로 회수하기 위한 공정을 선택해야 한다.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제32권5호
• /
• pp.406-415
• /
• 2010

Purpose: The secondary correction of cleft lip nasal deformity still presents a difficult surgical problems. The present study was aimed to investigate the usefulness of Bardach's technique for secondary correction of cleft lip nasal deformity. Materials and Methods: The subjects were eight patients with unilateral and bilateral cleft lip nasal deformity, who had secondary correction by using Bardach's rhinoplasty technique. Age range was from 2 to 21 years and mean age was 10.6 years. There were 3 boys and 5 girls. Six patients had bilateral and two patients had unilateral cleft lip. Facial photographs were taken before and twenty days after the operation. By using Adobe photoshop, the columella height and the nostril width were measured from the facial frontal photograph and Worm's eye view. The degree of improvement was calculated and statistically analyzed. Results: The degree of improvement of the columella length and the nostril width after Bardach's technique was $70.39{\pm}50.14%$ and $-22.93{\pm}0.15%$ respectively. Bardach's technique resulted in projecting the nasal tip, lengthening the columella, medially advancing the alar bases, restructuring the lower lateral cartilages, and changing orientation of the nostrils from horizontal to oblique. The profile view shows projection of the nasal tip, lengthening of the columella, and the change in the nasolabial angle. The scars remained at the philtrum were matter little in compared with improvement of the nasal appearance. Conclusion: These results indicate that Bardach's technique is an useful surgical technique for secondary correction of cleft lip nasal deformity.

• 한국입자에어로졸학회지
• /
• 제9권2호
• /
• pp.89-102
• /
• 2013

24-hr $PM_{2.5}$ samples were collected from January 19 through February 27, 2009 at an urban site of Gwangju and analyzed to determine the concentrations of organic and elemental carbon(OC and EC), water-soluble OC(WSOC), eight ionic species($Na^+$, $NH^{4+}$, $K^+$, $Ca^{2+}$, $Mg^{2+}$, $Cl^-$, ${NO_3}^-$ and ${SO_4}^{2-}$), and 22 elemental species. Haze phenomena was observed during approximately 29%(10 times) of the whole sampling period(35 days), resulting in highly elevated concentrations of $PM_{2.5}$ and its chemical components. An Asian dust event was also observed, during which $PM_{2.5}$ concentration was 64.5 ${\mu}g/m^2$. Crustal materials during Asian dust event contributed 26.6% to the $PM_{2.5}$, while lowest contribution(5.1%) was from the haze events. OC/EC and WSOC/OC ratios were found to be higher during haze days than during other sampling days, reflecting an enhanced secondary organic aerosol production under the haze conditions. For an Asian dust event, enhanced concentrations of OC and secondary inorganic components were also found, suggesting the further atmospheric processing of precursor gases during transport of air mass to the sampling site. Correlations among WSOC, EC, ${NO_3}^-$, ${SO_4}^{2-}$, and primary and secondary OC fractions, which were predicted from EC tracer method, suggests that the observed WSOC could be formed from similar formation processes as those of secondary organic aerosol, ${NO_3}^-$ and ${SO_4}^{2-}$. Results from principal component analysis indicate also that the observed WSOC was strongly associated with formation routes of the secondary organic and inorganic aerosols.

• Journal of Radiation Protection and Research
• /
• 제46권2호
• /
• pp.39-47
• /
• 2021

Background: The National Institutes for Quantum and Radiological Science and Technology-National Institute of Radiological Sciences (QST-NIRS) has continuously investigated the undesired radiation exposure in ion beam radiotherapy mainly in carbon-ion radiotherapy (CIRT). This review introduces our investigations on the secondary neutron dose in CIRT with the broad and scanning beam methods. Materials and Methods: The neutron ambient dose equivalents in CIRT are evaluated based on rem meter (WENDI-II) measurements. The out-of-field organ doses assuming prostate cancer and pediatric brain tumor treatments are also evaluated through the Monte Carlo simulation. This evaluation of the out-of-field dose includes contributions from secondary neutrons and secondary charged particles. Results and Discussion: The measurements of the neutron ambient dose equivalents at a 90#x00B0; angle to the beam axis in CIRT with the broad beam method show that the neutron dose per treatment dose in CIRT is lower than that in proton radiotherapy (PRT). For the scanning beam with the energy scanning technique, the neutron dose per treatment dose in CIRT is lower than that in PRT. Moreover, the out-of-field organ doses in CIRT decreased with distance to the target and are less than the lower bound in intensity-modulated radiotherapy (IMRT) shown in AAPM TG-158 (American Association of Physicists in Medicine Task Group). Conclusion: The evaluation of the out-of-field doses is important from the viewpoint of secondary cancer risk after radiotherapy. Secondary neutrons are the major source in CIRT, especially in the distant area from the target volume. However, the dose level in CIRT is similar or lower than that in PRT and IMRT, even if the contributions from all radiation species are included in the evaluation.

• Design & Manufacturing
• /
• 제16권4호
• /
• pp.34-39
• /
• 2022

Sustained economic development around the world is accelerating resource depletion. Research and development of secondary batteries that can replace them is also being actively conducted. Secondary batteries are emerging as a key technology for carbon neutrality. The core of an electric vehicle is the battery (secondary battery). Therefore, in this study, the temperature change by the heat source of the hammer and the rotational speed (rpm) of the abrasive disc of the Classifier Separator Mill (CSM) was repeatedly calculated and analyzed using the heat flow simulation STAR-CCM+. As the rotational speed (rpm) of the abrasive disk increases, the convergence condition of the iteration increases. Under the condition that the inlet speed of the Classifier Separator Mill (CSM) and the heat source value of the disc hammer are the same, the disc rotation speed (rpm) and the hammer temperature are inversely proportional. As the rotational speed (rpm) of the disc increases, the hammer temperature decreases. However, since the wear rate of the secondary battery material increases due to the strong impact of the crushing rotational force, it is determined that an appropriate rpm setting is necessary. In CSM (Classifier Separator Mill), it is judged that the flow rate difference is not significantly different in the direction of the pressure outlet (Outlet 1) right above the classifier wheel with the fastest flow rate. Because the disc and hammer attachment technology is adhesive, the attachment point may deform when the temperature of the hammer rises. Therefore, it is considered necessary to develop high-performance adhesives and other adhesive technologies.

• Carbon letters
• /
• 제16권3호
• /
• pp.135-146
• /
• 2015

Graphite can be classified into natural graphite from mines and artificial graphite. Due to its outstanding properties such as light weight, thermal resistance, electrical conductivity, thermal conductivity, chemical stability, and high-temperature strength, artificial graphite is used across various industries in powder form and bulk form. Artificial graphite of powder form is usually used as anode materials for secondary cells, while artificial graphite of bulk form is used in steelmaking electrode bars, nuclear reactor moderators, silicon ingots for semiconductors, and manufacturing equipment. This study defines artificial graphite as bulk graphite, and provides an overview of bulk graphite manufacturing, including isotropic and anisotropic materials, molding methods, and heat treatment.