• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.3
• /
• pp.504-511
• /
• 2001

Preventive resin restoration, extended concept of occlusal pit and fissure sealing, is procedure composed of as follows. Cavity preparation is limited to areas of initial caries The cavity is then restored with composite resin, while other sound pits and fissures are sealed with pit and fissure sealant. If pit and assure sealant with which microrestoration is possible is used, it may be of great benefit to both patient and operator in case of difficult-to-control children s treatment. However study on preventive resin restoration using this kind of materials have been scarce. The purpose of this study was to compare the microleakage of four different modes of preventive resin restoration. Restoration using only composite resin was compared together Fifty-five bicuspids were prepared with small class I cavity preparation on the occlusal surface, divided into the following groups and restored accordingly. Group 1 : Cavity was restored with Z-100 composite resin Group 2 : Cavity was restored with Z-100 composite resin. Pits and fissures were then sealed with Teethmate F-1 Group 3 : Cavity was restored with Z-100 composite resin Pits and fissures were then sealed with Ultraseal XT-plus Group 4 : Cavity and pits and fissures were restored with Ultraseal XT-plus altogrether Group 5 : Cavity was restored with Ultraseal XT-plus. Pits and fissures were then sealed with the same material. After restoration, the samples were thermocycled 500 times between $5^{\circ}C$ and $55^{\circ}C$ with a dwell time of 30 seconds. After thermocycling, the samples were dipped into 1% methylene blue solution for 24 hours, then rinsed with tap water. The teeth were then embedded in resin and cut buccolingually along the tooth axis and observed with a stereomicroscope to determine the degree of microleakage. The results were as follows : 1. Group 4 showed the greatest microleakage, while group 3, showed the least. The mean microleakage decreased in the following order:4>1>5>2>3. 2. There was no stastically significant difference between group 1 and group 5(p>0.05). However, group 1 showed significantly greater microleakage compared to group 2 and 3(p<0.05) Group 1 showed significantly less microleakage compared to group 4(p<0.05). 3. Group 2 showed no statistically significant difference compared to group 3(p>0.05). However group 2 showed significantly less microleakage compared to group 4 and 5(p<0.05) 4. Group 3 showed significantly less microleakage compared to group 4 and 5(p<0.05). 5. Group 5 showed significantly less microleakage than group 4(p<0.05).

• Electrical & Electronic Materials
• /
• v.12 no.7
• /
• pp.7-11
• /
• 1999

Fully sealed field emission display in size of 4.5 inch has been fabricated using single-wall carbon nanotubes-organic vehicle com-posite. The fabricated display were fully scalable at low temperature below 415$^{\circ}C$ and CNTs were vertically aligned using paste squeeze and surface rubbing techniques. The turn-on fields of 1V/${\mu}{\textrm}{m}$ and field emis-sion current of 1.5mA at 3V/${\mu}{\textrm}{m}$ (J=90${\mu}{\textrm}{m}$/$\textrm{cm}^2$)were observed. Brightness of 1800cd/$m^2$ at 3.7V/${\mu}{\textrm}{m}$ was observed on the entire area of 4.5-inch panel from the green phosphor-ITO glass. The fluctuation of the current was found to be about 7% over a 4.5-inch cath-ode area. This reliable result enables us to produce large area full-color flat panel dis-play in the near future. Carbon nanotubes (CNTs) have attracted much attention because of their unique elec-trical properties and their potential applica-tions [1, 2]. Large aspect ratio of CNTs together with high chemical stability. ther-mal conductivity, and high mechanical strength are advantageous for applications to the field emitter [3]. Several results have been reported on the field emissions from multi-walled nanotubes (MWNTs) and single-walled nanotubes (SWNTs) grown from arc discharge [4, 5]. De Heer et al. have reported the field emission from nan-otubes aligned by the suspension-filtering method. This approach is too difficult to be fully adopted in integration process. Recently, there have been efforts to make applications to field emission devices using nanotubes. Saito et al. demonstrated a car-bon nanotube-based lamp, which was oper-ated at high voltage (10KV) [8]. Aproto-type diode structure was tested by the size of 100mm $\times$ 10mm in vacuum chamber [9]. the difficulties arise from the arrangement of vertically aligned nanotubes after the growth. Recently vertically aligned carbon nanotubes have been synthesized using plasma-enhanced chemical vapor deposition(CVD) [6, 7]. Yet, control of a large area synthesis is still not easily accessible with such approaches. Here we report integra-tion processes of fully sealed 4.5-inch CNT-field emission displays (FEDs). Low turn-on voltage with high brightness, and stabili-ty clearly demonstrate the potential applica-bility of carbon nanotubes to full color dis-plays in near future. For flat panel display in a large area, car-bon nanotubes-based field emitters were fabricated by using nanotubes-organic vehi-cles. The purified SWNTs, which were syn-thesized by dc arc discharge, were dispersed in iso propyl alcohol, and then mixed with on organic binder. The paste of well-dis-persed carbon nanotubes was squeezed onto the metal-patterned sodalime glass throuhg the metal mesh of 20${\mu}{\textrm}{m}$ in size and subse-quently heat-treated in order to remove the organic binder. The insulating spacers in thickness of 200${\mu}{\textrm}{m}$ are inserted between the lower and upper glasses. The Y\ulcornerO\ulcornerS:Eu, ZnS:Cu, Al, and ZnS:Ag, Cl, phosphors are electrically deposited on the upper glass for red, green, and blue colors, respectively. The typical sizes of each phosphor are 2~3 micron. The assembled structure was sealed in an atmosphere of highly purified Ar gas by means of a glass frit. The display plate was evacuated down to the pressure level of 1$\times$10\ulcorner Torr. Three non-evaporable getters of Ti-Zr-V-Fe were activated during the final heat-exhausting procedure. Finally, the active area of 4.5-inch panel with fully sealed carbon nanotubes was pro-duced. Emission currents were character-ized by the DC-mode and pulse-modulating mode at the voltage up to 800 volts. The brightness of field emission was measured by the Luminance calorimeter (BM-7, Topcon).

• Fibers and Polymers
• /
• v.4 no.2
• /
• pp.71-76
• /
• 2003

We evaluated the seam characteristics with finishing, seaming and sealing processes and seam Puckering behavior of the breathable waterproof fabrics with laser scan. There were differences in 99% significant level between the seamed fabric and the sealed fabric. Seam breakage was initiated with the breakage of sewing thread, so the seam strength after seaming was almost uniform. The sewn seam strength and elongation increased with sealing process in all finishing methods. Pucker grade of laminating type was generally much higher than that of the coating type. We confirmed that wave length and amplitude have more important meaning than the number of weave in the breathable waterproof fabrics. The puckering in breathable waterproof fabrics is mainly occurred by inherent and feeding pucker. The former if due to the insertion of sewing thread and the littler is caused by differential feeding when two pieces of fabric are fed into the gap between a press foot and needle plate.

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.244-254
• /
• 1999

폐윤활유 재생용 TiO2 한외여과막은 정밀영과용 지르코니아 복합막(즉, 복층담채) 및 알루미나 단층 담체(기공크기 0.1$mu extrm{m}$)상에 졸-겔 코팅법에 의하여 TiO2 분리막 층을 코팅하여 제조 하였다. TiO2 졸의 특성 분석을 통하여 봉입침지(sealed dip-coating) 및 가압 코팅(pressurized coating)법으로 결함이 없는 TiO2 복합막을 제조할 수 있는 코팅조건을 최적화 하였다. 합성 TiO2 한외여과막의 분리막층 두께는 1$\mu\textrm{m}$이하의 범위에서 조절되었으며,기공값을 보여주었으며 75$0^{\circ}C$까지 열처리하여도 80%정도의 용질배제율(기공크기 22.5nm)을 유지하는 점으로 봐서 고온 공정을 요하는 폐윤활유 재생막으로서 충분한 열적 안정성을 갖고 있었다.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1693-1698
• /
• 2012

A headspace gas chromatographic mass spectrometric (GC-MS) assay method was developed for the simultaneous determination of methyl tertiary butyl ether (MTBE), $tert$-butyl alcohol (TBA) and benzene, toluene, ethyl benzene and xylene (BTEX) in soil contaminated with gasoline. 2 g of soil sample were placed in a 10 mL headspace vial filled with 5 mL of phosphoric acid solution (pH 3) saturated with NaCl, and the solution was spiked with fluorobenzene as an internal standard and sealed with a cap. The vial was heated in a heating block for 40 min at $80^{\circ}C$. The detection limits of the assay were 0.08-0.12 ${\mu}g$/kg for the analytes. For five independent determinations at 10 and 50 ${\mu}g$/kg, the relative standard deviations were less than 10%. The method was used to analyze fifty six soil samples collected from various regions contaminated with gasoline in Korea. The developed method may be valuable for the monitoring of the analytes in soil.

• Journal of Navigation and Port Research
• /
• v.37 no.1
• /
• pp.85-89
• /
• 2013

Sometimes, an evacuation should be executed from a ship for many reasons. This study considers on emergency evacuation on fire in a ship, one of the many reasons for evacuation. Due to the characteristic of fire, the most loss of life is known to be caused by suffocation resulted by smoke. To reduce the suffocation by smoke, the time available for evacuation should be improved for the higher survival rate of crews. In this study, crews' survival times and Evacuation time are analyzed quantitatively in during fire in the same sealed space in two different cases of the natural ventilation and the forced ventilation.

• Journal of Powder Materials
• /
• v.21 no.4
• /
• pp.260-265
• /
• 2014

In this study, in order to increase surface ability of hardness and corrosion of magnesium alloy, anodizing and sealing with nano-diamond powder was conducted. A porous oxide layer on the magnesium alloy was successfully made at $85^{\circ}C$ through anodizing. It was found to be significantly more difficult to make a porous oxide layer in the magnesium alloy compared to an aluminum alloy. The oxide layer made below $73^{\circ}C$ by anodizing had no porous layer. The electrolyte used in this study is DOW 17 solution. The surface morphology of the magnesium oxide layer was investigated by a scanning electron microscope. The pores made by anodizing were sealed by water and aqueous nano-diamond powder respectively. The hardness and corrosion resistance of the magnesium alloy was increased by the anodizing and sealing treatment with nano-diamond powder.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1511-1515
• /
• 2004

Machine vision system plays an important role in factory automation. Its many applications are found in automobile manufacturing industries, as an eye for robotic automation system. In this paper, an automobile position measuring vision system(APMVS) applicable to manufacturing line for under body painting of a car is introduced. The APMVS measures position and orientation of the car body to be sealed or painted by the robots. The configuration of the overall robotic sealing/painting system, design and application procedure, and application examples are described.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.111-114
• /
• 2001

Optical transmitter and receiver are the essential components for optical communication. For these components, butterfly type packages are used which are comprised of metal housing, multilayer ceramic inserts, lead and window. In this study, 2.5 Gbps DFB(Distributed -Feedback) LD(Laser Diode) package was fabricated and characterized. Metal housing showed good thermal conductivity (200W/mK) and well matched TCE(6.7ppm/K) with GaAs chip. Ceramic inserts also showed good VSWR(Voltage Standing Wave Ratio) characteristics(<2.0). By brazing technology, all the elements were combined and sealed. RF characteristics of the package mounted on the PWB was also tested.

• Journal of Microbiology and Biotechnology
• /
• v.4 no.2
• /
• pp.141-145
• /
• 1994

Conventional commercial thermal process for preparing Sikhae (Rice beverage) in a hermetically sealed container was evaluated to solve the nutritional deterioration and organoleptic inferiority problem caused by severe heat treatment. A milder thermal process with an aid of Nisin, a GRAS-grade, selectively germicidal compound, was introduced to destroy the putrefactive microorganisms. In this experiment, hot-filling method with Nisin, and thermal processing (at 110$^{\circ}C$ for 15 minutes with Nisin, at 121$^{\circ}C$ for 25 minutes without Nisin) were compared. The quality of Sikhae could be enhanced and over 90% of the thermal process could be conserved by this process in terms of sterilizing value without quality deterioration when processing the bottled Sikhae at 110$^{\circ}$ for 15 minutes $\{(F^{10}{_{121})_{process}=1.54\}$.