• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.325-330
• /
• 2000

In general steel sheet pile use the containment system, vertical barrier systems for waste disposal and landfill purposes, roads in excavation which have a more permanent character or temporary structure. The sheet pile joints between section of the wall are sealed with a filter material arid the resistance to seepage is a function of the type of material employed. The aim of this paper is to review a characteristic of permeability for Z type sheet pile by field test in various condition.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.589-593
• /
• 1995

The vibration of rotors in high speed sometimes leads to system failure or reduces the system life, and has a direct connection with stability. In this paper, the system's modelling was conducted in experimentally and the controller was designed to reduce the vibration due to the rotor unbalance using Squeeze Film Damper(SFD). SFD vibration control was achieved in constant rotating speed based on the controller designed. the control was confirmed working quite well in terms of both numerical simulation and experiment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.1004-1006
• /
• 1998

Mo-tip FED of 1 inch diagonal was vacuum sealed using sodalime-to-sodalime glass electrostatic bonding under $10^{-7}torr$. The bonding properties of the bonded sodalime-to sodalime structure were investigated and emission characteristic of packaged FED panel was measured.

• 한국전기전자재료학회논문지
• /
• 제15권11호
• /
• pp.976-980
• /
• 2002

This paper repors on low temperature sealing process of PDP using binder and capping glass. The exhausting hole on rear glass of PDP was sealed by capping glass using screen-printed binder without exhausting glass tube. Based on the tubeless packaging process, out gassing problem could be reduced and vacuum conductance could be improved by eliminating exhaust tube.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.217-224
• /
• 1998

This study describes examinations made for the purpose of obtaining data for strength control of mass concrete in the cold season. The examination in outline of analysis of temperatures of mass concrete(corresponding to member thickness of 1m) and comparisons with water-cured specimens of various concrete specimens cured in sealed condition. As a result, it was found that mass concrete placed in the cold season, if strength is controlled based on 28-day age, is seen to require a strength correction factor.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회 논문집(I)
• /
• pp.309-314
• /
• 1998

The moisture diffusion and self-desiccation cause the differential drying shrinkage and autogenous shrinkage at early ages, respecitvely. Thus total shrinkage strain includes the differential drying shrinkage and self-desiccation shrinkage. Thus in this study the shrinkage strain was measured at various positions in the exposed concrete and in the sealed concrete the self-desiccation shrinkage was measured. In low-strength concrete, the differential drying shrinkage increases very rapidly, but self-desiccation shrinkage is very small. But high-strength concrete shows the reverse result. And the analytical results for differential drying shrinkage were in good agreement with the test results.

• Tribology and Lubricants
• /
• 제10권3호
• /
• pp.12-17
• /
• 1994

Minimum clearance between the U-cup seal groove of a piston and a cylinder bore to ensure against extrusion of the U-cup ring and leakage of working fluids is an important design parameter for a seal designer in hydraulic cylinder applications. Therefore, typical U-cup seal of a hydraulic actuator has been analyzed as a function of a sealing gap using the nonlinear FEM software MARC. In this study, the useful design data were presented as a function of the sealing gap and the sealed hydraulic pressure.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.356-363
• /
• 2001

Piston seal is a device designed to prevent leakage in split connecctions or between relatively moving part. Contact force, critical pressure at which extrusion occurs, leakage rate, fluid film thickness and friction force have been analyzed for some design parameter such as clearance between cylinder wall piston, depth of rectangular groove and pressure of sealed hydraulic fluid. In this paper, we analyze displacement and stress of Wearing by finite element analysis to understand Contact Behaviour Characters.

• 대한치과의사협회지
• /
• 제50권9호
• /
• pp.574-585
• /
• 2012

Purpose : This study was performed to evaluate the healing response around the root perforation restorative material. Materials and Methods : Four beagle dogs were used for experimental study. Endodontic treatment was performed at four maxillary premolars and artificial perforation was formed at furcation area of pulp chamber. Canal was filled with gutta percha cone and the perforation was sealed with MTA at group 1. At group 2, canal was filled and the perforation was sealed with dentin paste. Tooth paste was fabricated using extracted human teeth. Histologic examination of furcation area was performed 2, 4, 8 and 12 weeks after experiment. Results : New trabecular bone formation was observed around the MTA and tooth paste. Lamellar bone was observed as time is over. There were no inflammatory reaction in both groups. Conclusion : There is a possibility which endodontic filling material can be developed using extracted teeth.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2005년도 추계 학술대회 논문집
• /
• pp.87-95
• /
• 2005

삼중수소를 사용하는 자발광유리관의 제조에 필요한 4가지 핵심 기술 중 레이저를 이용한 밀봉/절단기술을 개발하였다. 상용 제품을 분석한 결과 유리관의 재질은 pyrex 이었고 레이저는 유리가공에 적절한 펄스형 이산화탄소 레이저를 사용하였다 유리관의 밀봉/절단에 영향을 미치는 인자들로는 레이저빔의 강도 지속시간 조사 방법, 유리관 내부의 압력 등이었다. 전 공정은 2단계로 이루어져 1단계에서는 삼중수소를 주입하고 유리관의 양단을 밀봉하였으며 2단계에서는 삼중수소가 봉입된 유리관을 원하는 길이로 밀봉/절단하였다. 각 공정에서 유리관의 밀봉은 defocusing된 레이저빔을 사용하였으며 절단은 focusing된 빔을 사용하였다. 밀봉/절단 후에는 잔여 열응력에 의한 파열을 방지하기 위하여 열처리를 하였다.