• 한국의류산업학회지
• /
• 제9권4호
• /
• pp.445-449
• /
• 2007

The results of warmth retaining, heat transfer and compressive elastic recovery of the five kinds of bedspread fabrics, which were produced from packing weft of 2700 denier and 3600 denier batt yarn treated with raw material of Polyester $150^D$/48 DTY, are as follows: 1) 3600 denier packing weft showed lover count in compressive elastic recovery than 2700d packing weft, so it took longer time to recover. 2) When packing weft of the same count is used, a sample of packing weft with higher density showed lower recovery. 3) It took 2700d packing weft 30min to get approximately 98% recovery in temperature $30^{\circ}C$. But, 3600d packing weft stayed under 98% recovery in the same temperature. Considering only the result of compressive elastic recovery, we should use 2700d packing weft. 4) The higher the density of packing weft is, the higher warmth retaining becomes. Although sharp increase appeared until 5min, equilibrium was kept without any increase after that time. 5) When 2700d packing weft was used, the maximum warmth retaining was approximately 60% and 64% in the conditions of density 12(thread/in) and 22(thread/in) respectively.

• 한국의류학회지
• /
• 제23권7호
• /
• pp.998-1006
• /
• 1999

This study has investigated the relation between the sewing speed and seam breaking strength applied perpendicular to the seam direction. Breaking strength efficiency breaking mode of seams were examined under various sewing conditions using three kinds of sewing threads and four kinds of fabrics. The results obtained are as follows : 1. According to the increase in sewing speed seam strength was remarkably decreased. Seam strength and its loss difference were shown variously as threads and fabrics were mixed. 2. In case of fabrics with higher strength seam strength showed higher. And the seam strength was determined by the loop strength. 3. In case of fabrics with lower strength seam strength and its difference for every sample showed lower. So the strength of fabrics dominated the seam strength than those of threads. 4. In the experiment using various fabrics and sewing threads there was a type of thread appropriate to each fabric. Fabrics and threads with have similar physical properties were shown proper seam efficiency. 5. The breaking mode was different for every sample seam that was tested.

• 보존과학회지
• /
• 제32권1호
• /
• pp.43-49
• /
• 2016

금사는 금속물로 제작된 실을 의미하며, 다양한 재료와 재질이 혼합하여 사용되고, 제작 방식에 따라 다양한 형태가 구분된다. 같은 형태일지라도 지역에 따라 사용재료가 다르게 나타나기 때문에 금박, 접착제, 배지 등에 대한 기초 자료 조사는 제작기법 및 유물의 제작국가에 대한 정보를 확인할 수 있기에 중요하다. 이에 본 연구는 직금 유물에 사용된 전통 편금사의 접착특성 및 제작기법 분석을 위한 연구를 진행하였다. 지역 및 시대가 다른 직금 유물을 선정하여 시료를 일부 채취하였다. 전통 금사에 사용했을 것으로 추정되는 접착제를 선정하여, 종류별로 표준시료를 제작하였다. 접착제는 아교, 주토 혼합 아교, 옻, 주칠을 선정하였으며, 식물성 배지인 한지 위에 접착제를 바른 후 순금박을 올렸다. 직금유물에서 채취한 금사와 제작한 표준시료를 일부 채취하여 형태 및 무기원소 성분 분석을 하였다. 연구 결과, 편금사는 금박층, 접착층, 배지층으로 구분이 되는 것을 확인할 수 있었다. 표준시료와 비교 관찰한 결과, 아교 및 주칠혼합시료와 형태적으로 유사하였다. 붉은색 접착층에 대한 정성분석 결과 알루미늄(Al), 규소(Si), 철(Fe) 성분이 현미경에서 관찰된 붉은색과 일치함에 따라 전통 편금사는 아교에 주토를 혼합하여 접착제로 사용한 것으로 판단된다. 이러한 사실은 국내 문헌 및 국외사례를 통해서도 확인할 수 있으며, 아교에 주토를 혼합함으로써 발색 및 평활도에서 효과를 얻고자 함으로 사료된다. 또한 이러한 방법은 옻을 접착제로 사용하는 일본과는 달리 중국, 한국에서 공통적으로 관찰되는 제작방법이라는 사실도 확인할 수 있었다.본 연구를 통해 향후 전통 금사의 재현 및 생산기술에 대한 기초 자료로 활용될 것으로 기대된다.

• 대한치과보철학회지
• /
• 제40권3호
• /
• pp.275-286
• /
• 2002

Statement of problem. Surface alteration of the implant screws after function may be associated with mechanical failure. Theses metal fatigue appears to be the most common cause of structural failure. Purpose. The purpose of this study was to evaluate surface alteration of the implant screws after function through the examination of used and unused implant screws in SEM(scanning electron microscope). Materials and methods. In this study, abutment screws(Steri-oss, 3i), gold retaining screw(3i) and titanium retaining screw(3i) were retrieved from patients. New, unused abutment and retaining screws were prepared for control group. Each of the old, used screws was retrieved with a screwdriver. And retrieved implant complex of Steri-oss system was prepared for this study. Then, SEM investigation and EDS analysis of abutment and retaining screws were performed. And SEM investigation of cross-sectioned sample of retrieved implant complex was performed. Results. In the case of new, unused implant screws, as maunfactured circumferential grooves are regularly examined and screw thread are sharply remained. Before ultrasonic cleansing of old, used implant screw, a lot of accumulation and corrosion products were existed. After ultrasonic cleansing of old, used implant screws, circumferential grooves as examined before function were randomly deepened and scratches increased. Also, dull screw thread was examined. More surface alterations after function were examined in titanium screw than gold screw. And more surface alteration was examined when retrieved with driver than retrieved without driver. Conclusions. These surface alteration after function may result in the screw instability. Regularly cleansing and exchange of screws was recommended. We recommend the use of gold screw rather than titanium screw, and careful manipulation of the driver.

• 한국콘텐츠학회논문지
• /
• 제18권3호
• /
• pp.320-329
• /
• 2018

본 연구의 목적은 결혼을 통해 부부의 인연을 맺은 배우자에 대한 인식을 질적 연구방법인 'Q방법론'을 활용하여 유형화하는 데 있다. 본 연구에서는 배우자가 있는 기혼자 42명을 P 표본으로 하여 최종 도출된 42개의 Q 표본을 9점 척도 상에 강제 분포하도록 하였다. 수집된 자료는 PC QUANL program을 이용하여 분석하였다. 연구결과 배우자에 대한 주관성은 2가지 유형으로 도출되었다. 유형 I(n=36)은 '사랑-인연형', 유형 II(n=6)는 '실타래-책임자형'으로 정의되었다. 유형 I은 배우자에 대한 사랑을 강조하면서 배우자를 인연과 운명으로 인식하였고, 유형 II는 배우자를 실타래를 풀 듯 노력이 필요한 대상이며 책임져야 할 존재로 여기는 인식을 보였다. 본 연구 결과 2가지 유형 간의 구조적인 차이점이 발견되었고, 유형에 따른 특성에 기초하여 보다 건강하고 행복한 결혼생활을 지원하기 위한 기초자료로 활용할 수 있을 것이다.

• 한국의류산업학회지
• /
• 제7권3호
• /
• pp.346-350
• /
• 2005

In this study, to investigate the influence on the seam puckering by the mechanical properties of textiles, it was measured from 4 polyester/cotton samples. We reached the following conclusion in influences of the seam puckering by the thread, iron and laundry. Seam puckering is occurred several times by repeating the laundry. according to iron method, the seam puckering is stronger in order of T/C1> T/C2> T/C3> T/C4 by the samples and order of 40's/2> 60's/3> 50's/2> 60's/2 by the threads, the relation between sample's mechanical properties and seam strength and obtainment of formula. We can find that seam puckering is related with B, 2HB, G, 2HG5, RC, T among the mechanical properties and the estimated formulas which get from mechanical factors.

• 한국의류학회지
• /
• 제21권6호
• /
• pp.1010-1020
• /
• 1997

For this study, we did needlework of the sample considering practical aspects of production and consumption of silk, high-quality material for women's clothes, and then analyzed the state of the seam puckering after press and dry cleaning, estimated the Seam Puckering based on the mechanical properties of silk related to machine sewing, and examined the effects which Mechanical Properties have on Seam Puckering closely. Through this, we reach the following conclusion. 1. There are three types of seam puckering for each stage, which are caused bathe smoothness of the surface by press, and the difference between the shrinkage rates of fabric and sewing thread by Dry Cleaning. 2. In analyzing seam puckering classified by each step, seam puckering after sewing the fabric is related to WT negatively, while to RT and W positively. Seam puckering after sewing and pressing the fabric is related to WT, RC, MMD negatively and seam puckering after sewing, pressing anddry cleaning the fabric isrelated to WT negatively, too. 3. Concerning the mechanical properties of the sample with a little seam puckering, WT, LC, WC, RC, MMD, SMD is relatively large while RT, B, 2HB is small. 4. Judging from the result of estimating seam puckering based on mechanical properties, the estimate-formula is satisfied in this study.

• Journal of the Optical Society of Korea
• /
• 제15권4호
• /
• pp.386-393
• /
• 2011

In this study, we report an effective k-domain linearization method with a pre-calibrated indexed look-up table. The method minimizes k-domain nonlinear characteristics of a swept source optical coherence tomography (SS-OCT) system by using two arrays, a sample position shift index and an intensity compensation array. Two arrays are generated from an interference pattern acquired by connecting a Fabry-Perot interferometer (FPI) and an optical spectrum analyzer (OSA) to the system. At real time imaging, the sample position is modified by location movement and intensity compensation with two arrays for linearity of wavenumber. As a result of evaluating point spread functions (PSFs), the signal to noise ratio (SNR) is increased by 9.7 dB. When applied to infrared (IR) sensing card imaging, the SNR is increased by 1.29 dB and the contrast noise ratio (CNR) value is increased by 1.44. The time required for the linearization and intensity compensation is 30 ms for a multi thread method using a central processing unit (CPU) compared to 0.8 ms for compute unified device architecture (CUDA) processing using a graphics processing unit (GPU). We verified that our linearization method is appropriate for applying real time imaging of SS-OCT.

• 대한금속재료학회지
• /
• 제49권1호
• /
• pp.1-8
• /
• 2011

To measure the sensitivity of the hydrogen embrittlement from plated high strength bolts (SWCH18A, F11T), the bolt was stressed by a corresponding to the amount of tensile strain of 5% and 20%, and then the bolt developed a crack on the surface. The bolt that didn't have concentrated hydrogen, even though it was stressed by a corresponding the amount of tensile strain of 5% and 20%, no crack developed. However, the bolt that had concentrated hydrogen, developed cracks from the thread crest to the root. It is impossible to measure the hydrogen amount from plated high strength bolts using Hydrogen-Determinator, because of the limitation of the minimum sample size (about 1g as a mass or $5{\times}5{\times}5 mm^3$ as a volume). Therefore, the sensitivity of hydrogen embrittlement can be measured by observing the presence of cracks on the surface of plated high strength bolts which are stressed by a corresponding to the amount of tensile strain of 5% and 20%.

• 한국잠사곤충학회지
• /
• 제38권2호
• /
• pp.160-167
• /
• 1996

견단백질을 구성하는 액상견사막인 중부견사막을 추출한 후, 약3배로 급속히 연신하여 견 monofilament를 제작하였다. 이 시료를 연화시켜 분자간의 수소결합능을 저하시키기 위해 비등상태의 증류수에 팽윤시킨 다음 연신처리를 행한 결과는 다음과 같다. 1. 열분석과 X선회석의 결과로부터 견사막건조물시료은 Silk I형의 결정영역 및 random 무정형분자로 구성되어 있었으나 monofilament시료에서는 부분적으로 Silk II형결정이 발현하기 시작하여 더욱더 연신한 62.5% 연신시료에서는 거의 완전한 Silk II형결정으로 전이하는 것을 알 수 있다. 2. 복굴절율 및 밀도는 monofilament시료에 비해 연신율의 상승과 함께 증가하는 경향을 나타내어 견 fibroin분자의 배향은 초기에 급격히 증가하여 fibroin분자의 배향이 완성되었다. 3. 가수분해처리에 의한 복굴절율은 연신율의 상승에 따라서 증가하는 경향이었다. 또, 가수분해의 처리시간과의 관계에서는 연신율이 증가함에 따라 복굴절율도 거의 일정하게 나타나 배향결정화가 진행되어 배열이 좋게 되어진 무정형이 결정으로 전이하는 것이 시사되었다. 4. 62.5% 연신시료를 가수분해한 경우의 X선회절은 가수분해에 의해 배향의 흐트러짐은 생기나 결정풍괴는 일어나지 않았다. 열분석에서도 가수분해의 처리시간이 증가함에 따라 최대흡열 peak 온도는 저온측으로 이동하여 가수분해처리에 의해 고배향의 무정형부분이 유출로 인하여 결정부분의 배향이 흐트러진다는 것이 X선분석 결과로부터 추측되어진다.