• Journal of Biosystems Engineering
• /
• 제36권5호
• /
• pp.319-325
• /
• 2011

This study was conducted to figure out the diagnosis basis of cooling performance depending on water amount in the refrigerant of air conditioner, which can be estimated by the temperatures and pressures along the refrigerant circulation line. A car air conditioner of SONATA III (Hyundai motor Co., Korea) was tested at maximum cooling condition at the engine speed of 1500 rpm in the room controlled at 33~$35^{\circ}C$ air temperature and 55~57% relative humidity conditionally. Measured variables were temperature differences between inlet and outlet pipe surfaces of the compressor, condenser, receive drier and evaporator; and high pressure and low pressure in the refrigerant circulation line; and temperature difference between inlet and outlet air of the cooling vent of evaporator. In this study, changes of the water amount in the refrigerant were correlated to the temperatures and pressure changes and also water amount caused poor cooling performance. As water amount increased in the refrigerant in the air conditioner, the performance of the cooling or the heat transfer became worse. Temporal variations of the surface temperature of the evaporator outlet pipe and the low-side pressure showed various patterns that could estimate the water amount. When the water amount caused bad cooling performance, the patterns of the temperature of the evaporator outlet pipe indicated irregular fluctuation greater than $5^{\circ}C$. When the diagnosis system is using just external sensors of the low-side pressure and the temperatures of inlet and outlet air of cooling vent of the evaporator, the precise pattern of bad cooling performance caused by excess water amount in the cooling line was irregular pressure fluctuation, 25 kPa under 120 kPa, and temperature, $12^{\circ}C$ and less.

• 한국재료학회지
• /
• 제2권2호
• /
• pp.119-125
• /
• 1992

수평자장을 건 Czochralski(HMCZ) 방법으로 자장강도(B)와 도가니 회전속도(C)가 실리콘 단결정의 산소편석에 미치는 영향에 대하여 연구하였다. B=2, 3, 4kG와 C=4-15rpm에서 <100> 방향으로 성장시킨 57mm 직경의 단결정들 내의 산소분포는 대체로 축을 따라서 불균일하였고 톱니모양을 나타내었다. 종래의 CZ 방법과 비교할 때, 이러한 산소분포의 불균일성은 위 강도의 수평자장이 결정성장계면으로의 산소전달에 불안정한 요소로 작용했음을 나타낸다고 볼 수 있다. 반면에 C의 증가는 산소분포의 불균일성의 약화와 산소농도의 전반적인 증가를 유도하였다. 이 결과를 토대로 B=2kG에서 27-36ppma인 산소분포를 가진 단결정이 프로그램된 C에 의해서 얻어졌다. 소자제조공정을 모의한 열처리 과정에서 HMCZ 실리콘의 산소석출은 종래의 CZ 실리콘의 산소석출에 비해서 상대적으로 불균일하였고, as-grown 상태에서의 고르지 못한 HMCZ 실리콘의 산소분포가 주요 원인임이 밝혀졌다.

• 대한조선학회논문집
• /
• 제54권2호
• /
• pp.125-131
• /
• 2017

In order to develop test and performance analysis techniques for a CRP propulsion, a CRP dynamometer which can be installed inside the model ship was designed and manufactured. The object ship was the 16000TEU container carrier, which has test results for the single propeller. The design concept of the present CRP is that forward & after propellers have the same power ratio and their RPM ratio is 0.75:1. To begin with, we checked the performance of the CRP dynamometer through the calibration and then installed it inside the model ship. After the model ship setup including the design CRP and the rudder in the Large Cavitation Tunnel(LCT), a series of model tests composed of power ratio check, propeller behind wake(PBW) test, cavitation observation and pressure fluctuation tests was conducted. Through the model test and data analysis for CRP, the experimental technique was established and the improved method for CRP design was suggested.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.29-37
• /
• 1994

Active noise control of random noise which propatate in the vehicle cabin as a form of spherical wave is the target of this study. In the previous study, the adaptive algorithm for adaptive controller is presented for the application in active noise control system. And for the preliminary study of adaptive active noise control in vehicle cabin as a real system, a computer simulation is performed on the effectiveness of the adaptive algorithm in the amplitude of the pressure fluctuation. This work studies the implementation of multi-channel feedforward adaptive algorithm for the reduction of the noise inside a vehicle cabin using a number of secondary sources derived by adaptive filtering of reference noise source. Multi-channel adaptive feedforward algorithm are verified in numerical simulation and semi-experimental justification of developed system is made on a domestic passenger car. In the results of semi-experimental study, the noise of specific region in the interior of automobile are reduced for the appreciabe sound pressure level in the operating engine rpm and finally this study suggests the capabilities of the real time active noise control in 3 dimensional acoustic fields.

• Journal of Biosystems Engineering
• /
• 제16권2호
• /
• pp.124-132
• /
• 1991

This study was carried out to obtain the information needed in the development of forward speed control system and the improvement of combine performance. The effects of variety, grain moisture content and forward speed on the combine load characteristics were investigated through experiments. The results of this study are summarized as follows. 1. A data acquisition system was developed to measure the engine speed and the torques and speeds of the threshing cylinder, dean-grain auger and tailings-return auger. The system consisted of transducers, signal conditioner, interface board and microcomputer. The system accuracy is better than ${\pm}2.3%$ full scale. 2. Linear regression equations were obtained for the torque, speed and power requirement of threshing cylinder for different paddy varieties, grain moisture contents and feed rates. 3. The maximum value of relative frequency for threshing cylinder torque decreased as the increase in feed rate and moisture content. The range of torque fluctuation was 1.2~3.7 and 1.2~1.9 times the average and maximum torque, respectively. The maximum value of power spectrum density (PSD) appeared to be about 11 Hz regardless of paddy variety, grain moisture content and feed rate. 4. The speed of tailings return thrower decreased rapidly at below 900rpm, and it fell to near zero about 3 seconds after that time. When the travelling of combine harvester was stopped immediately after sensing the overload, it took about 7 seconds for a full recovery of the no-load speed of tailings return thrower.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.904-907
• /
• 2002

Optical disk drive device is improved in rotating speed for faster data reading. In the case of CD-ROM, rotating speed is over 10000 rpm in the practical use. As a result of high rotating speed, unexpected effects as like increasing disk fluctuation and acoustic noise are raised by the air friction on the rotating disk and the eccentricity of rotating parts. The overall acoustic noise of running CD-ROM could be classified into two different characterized noise. The first is the structural-borne noise which is generated from vibrating solid body. By the reason, the signal of structural borne noise has very similar to the signal of surface vibrating one. It has dense noise energy at specific frequency region. The other is the air-borne noise which is generated from turbulence or vortex caused by friction between disk and air. The signal of air-borne noise has no dominant peak point at acoustic pressure-frequency domain. The noise energy is widely distributed while comparatively high and large frequency region. The structural-borne noise could be reduced by reducing vibration of structure and in addition it's target reducing frequency is narrow. However the air-borne noise reduction is effectively needed of enclosing method for the noise source located near the disk surface because it is difficult to define target frequency point. In this study, the acoustic noise at driving CD-ROM is classified by the sides of it's character and tried to reduce the overall acoustic noise.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2001년도 춘계학술발표논문집
• /
• pp.81-81
• /
• 2001

초지 공정은 wire, roll, pump등의 회전체로 이루어진 공정이 거의 대부분이기 때문에 주기적으로 변동하는 성분들이 많고, QCS(Quality Control System) 및 DCS(Distributed Co n ntrol System)상에 서 의 자동 Control Logic에 의 한 불안정 (Fluctuation)요소도 내 재 되 어 있 어 이에 대한 분석이 필요하다. 이러한 주기적인 변동은 제품의 여러 물성(평량, 두께, 광택 도등) 에 영향을 미치게 되어 품질의 균일성이나 프로파일에 영향을 미치게 된다. 따라서 공정상이나 품질에서 주기적으로 변동하는 성분을 추출하여 공정 각 성분과 연관을 시키변 품질에 나타나는 주기적 성분의 요인이 어느 부분에서 기인하는 지를 직접적으로 찾아낼 수 있고 이의 개선을 통해 품질의 균일성 및 프로파일 향상을 꾀할 수 있다. 본 연구에서는 Air padded type 헤드박스 초지기에서 DAQ(Data Acquisition) System 을 이용하여 각 공정별로 MD(Machine Direction)방향으로의 변동을 측정하고 제품의 물성 변동과 비교하였다. DAQ System은 각 공정상의 전기적 신호를 높은 주파수 영역까지 다채널로 동시에 받 아 들일 수 있는 장치로 이 시스템을 활용하여 공정상의 Machine chest 농도, Stock box 유량 및 레벨, Fan pump RPM, Cleaner압력, Screen압력, H!B압력 및 레벨, Silo level등 공 정요소의 변동상태와 상호영향을 분석하였다. 이러한 공정 각 요소의 변동과 MD 방향의 제품 물성 값(Tapio, Paper Variation Analyzer에 대한 비교 분석결과 제품 평량에서 주기적인 변동성분을 확인할 수 있었고 이중 큰 비 중을 차지하는 것이 fνB 레벨 변동주기와 일치하는 것을 찾아낼 수 있었다. 이에 근거하여 D DCS system의 control 요소인 튜닝 parameter(P,I 값)들을 미 세 조정 하여 제 품의 MD방향 평량 변동 진폭을 기존 수준의 30% 수준으로 감소시킬 수 있었다. 그 결과 COV(표준편차/ 평량)값을 0.8-1.2%에서 0.6-0.8%수준으로 낮출 수 있었고 이에 따라 CD (Cross Direction) 방향의 제품 Profile도 함께 개선되는 효과를 거둘 수 있었다.