• Title/Summary/Keyword: rock-soil

Search Result 1,074, Processing Time 0.028 seconds

Analysis of Characteristics of Landslide Susceptibility in Rugged Mountain Range in the Korean National Park (산악형 국립공원지역의 산사태 발생과 취약지역 특성 분석)

  • Lee, Sung-Jae;Lee, Eun-Jai;Ma, Ho-Seop
    • Journal of Korean Society of Forest Science
    • /
    • v.108 no.4
    • /
    • pp.552-561
    • /
    • 2019
  • In korea, debris-flow disasters are induced by typhoon and localized torrential rainfall annually. These disasters are particularly severe in the Korean national park due to its geomorphological characteristics. This study was conducted to analyze the landslide characteristics and forest environmental factors of landslide areas located in rugged mountain range in the Korean national park (Mt. Seorak, Mt. Jiri, and Mt. Sobaek). Overall, landslides occurred at 474 sites. The average area of the landslide scar among these sites was 1,212 ㎡. The average landslide sediment was 1,389 ㎥, average landslide length was 75 m, and the average width was 12.9 m. The landslides frequently occurred in regions with igneous rock and coniferous forest. In addition, slope gradient degree (31°-40°), slope gradient direction (N), vertical slope (concave), cross slope (concave), altitude (401-800 m), position (middle), stream order (first order), forest type (mixed), parent rock (igneous), and soil depth (<46 cm). The relationship between landslide soil volume and environmental factors showed positive correlation. The variables of vertical slope (complex), altitude (<1,201 m), and soil depth (<46 cm) correlated significantly at 1 % level.

Structural-Health Evaluation for Core Zones of Fill Dams in Korea using Electrical Resistivity Survey and No Water Boring Method (전기비저항 탐사와 무수보링을 이용한 국내 필 댐 코어존의 건전성 평가)

  • Lee, Sangjong;Lim, Heuidae;Park, Dongsoon
    • Journal of the Korean GEO-environmental Society
    • /
    • v.16 no.8
    • /
    • pp.21-35
    • /
    • 2015
  • Electrical resistivity survey (2D and 3D) were employed for detection of possible weak zone of core zones of three central core earth-rockfill dams in Korea. In the 2D results, the core zones is lower resistivity zone with less than $50{\sim}400ohm{\cdot}m$, and the basement is relatively higher resistivity zone with over $1,000ohm{\cdot}m$. In the 3D results, especially, the weak zone with under $100ohm{\cdot}m$ was detected spatial distribution area in the dam. We also drilled boreholes to collect soil samples of core zones of each dam. Water was not used during boring, because water for rotary wash boring could cause structural damages in earth dams. We found that the soil samples of core zones from all of the boreholes correspond to CL (USCS), but we also found that the fluidized or water-saturated soil samples were found in lower resistivity zones. Therefore, the electrical resistivity survey and drilling method without water are a quick and efficient method for structural-health evaluation which is detection of possible weak zones in earth core rockfill dams.

Analysis of Characteristics of Horizontal Response Spectrum of Ground Motions from 19 Earthquakes (국내 관측자료를 이용한 수평 응답스펙트럼 특성 분석)

  • Kim, Jun-Kyoung
    • Tunnel and Underground Space
    • /
    • v.20 no.6
    • /
    • pp.399-407
    • /
    • 2010
  • The horizontal response spectra using the observed ground motions from the recent more than 19 macro earthquakes were analysed and then were compared to both the seismic design response spectra (Reg Guide 1.60), applied to the domestic nuclear power plants, and the Korean Standard Design Response Spectrum for general structures and buildings (1997). 130 horizontal ground motions, without considering soil types, were used for normalization with respect to the peak acceleration value of each ground motion. The results showed that response spectrum have strong dependency on epicentral distance. The results also showed that the horizontal response spectra revealed much higher values for frequency bands above 5 Hz than Reg. Guide (1.60). The results were also compared to the Korean Standard Response Spectrum for the 3 different soil types and showed that the vertical response spectra revealed much higher values for the frequency bands below 0.3 second than the Korean Standard Response Spectrum (SD soil condition). These spectral values dependent on frequency could be related to characteristics of the domestic crustal attenuation and the effect of each site amplification. However, through the qualitative improvements and quantitative enhancement of the observed ground motions, the conservation of horizontal seismic design response spectrum should be considered more significantly for the frequency bands above 5 Hz.

Evaluation of Soil-Water Characteristic Curve for Domestic Bentonite Buffer (국내 벤토나이트 완충재의 함수특성곡선 평가)

  • Yoon, Seok;Jeon, Jun-Seo;Lee, Changsoo;Cho, Won-Jin;Lee, Seung-Rae;Kim, Geon-Young
    • Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
    • /
    • v.17 no.1
    • /
    • pp.29-36
    • /
    • 2019
  • High-level radioactive waste (HLW) such as spent fuel is inevitably produced when nuclear power plants are operated. A geological repository has been considered as one of the most adequate options for the disposal of HLW, and it will be constructed in host rock at a depth of 500~1,000 meters below ground level with the concept of an engineered barrier system (EBS) and a natural barrier system. The compacted bentonite buffer is one of the most important components of the EBS. As the compacted bentonite buffer is located between disposal canisters with spent fuel and the host rock, it can restrain the release of radionuclides and protect canisters from the inflow of groundwater. Because of inflow of groundwater into the compacted bentonite buffer, it is essential to investigate soil-water characteristic curves (SWCC) of the compacted bentonite buffer in order to evaluate the entire safety performance of the EBS. Therefore, this paper conducted laboratory experiments to analyze the SWCC for a Korean Ca-type compacted bentonite buffer considering dry density, confined or unconfined condition, and drying or wetting path. There was no significant difference of SWCC considering dry density under unconfined condition. Furthermore, it was found that there was higher water suction in unconfined condition that in confined condition, and higher water suction during drying path than during wetting path.

Engineering Geological Analysis of Landslides on Natural Slopes Induced by Rainfall - Yongin$\cdot$Ansung Area - (강우에 의해 발생된 자연사면 산사태의 지질공학적 분석 - 용인$\cdot$안성지역을 대상으로 -)

  • Kim Kyeong-Su;Kim Won-Young;Chae Byung-Gon;Song Young-Suk;Cho Yong-Chan
    • The Journal of Engineering Geology
    • /
    • v.15 no.2 s.42
    • /
    • pp.105-121
    • /
    • 2005
  • Most of the landslides triggered by intensive rainfall on natural slope occur serious damages of human beings and properties. There have been many landslides since 1991 in Gyeonggi province. The influential factors are rainfall, topography, geology and soil properties. There were 660 landslides occurred by intensive rainfall as much as 250mm at Yongin and Anseong area from Tuly 19th to luly 21st,1991 This study surveyed location, topography, geology, geometry of the landslide and rainfall at the area and analyzed occurrence characteristics of the landslides. Most of the landslides occurred on the soil layer above the bed rock. They showed changes of landslide types from translational slides at the head part to flow at the central part. The landslides have relatively small magnitude of which length is shorter than 50m. In order to identify characteristics of landslides dependent on soil conditions, geotechnical properties of soil were evaluated by laboratory tests using soil samples which were collected on slided area and not-slided area. Soil properties of the slided area show high percentage of coarse material such as gravel and sand. However, soil of the not-slided area is mainly composed of fine material such as silt and clay. Permeability coefficients of the slided area are higher than those of the not-slided area.

The Effects of Site Environmental Factors on Estimation of Site Index Function for Chamaecyparis obtusa Endlicher Stands (입지환경인자를 바탕으로 한 편백의 지위지수 추정에 관한 연구)

  • Kim, Dae-Hyun;Kim, Eui-Gyeong;Lee, Sung-Gi;Chung, Young-Gyo;Jeong, Jin-Hyun
    • Journal of Environmental Science International
    • /
    • v.17 no.8
    • /
    • pp.891-898
    • /
    • 2008
  • This study was conducted to develop the effects of site environmental factors on estimation of site index function for Chamaecyparis obtusa Endlicher stands. We derived nonlinear growth equation and the draw site index curves by applying this estimated equation. This study with Chapman-Richards function showed significant P-value which was less then 0.0001 and $R^2$ value 0.5947. This study was conducted to develop the feasible site index equation of Chamaecyparis obtusa Endlicher. For the table, the data of 82 sample areas that were thought to be without errors among the data of Chamaecyparis obtusa Endlicher sample area located on the value-oriented forest location chart were used and estimated. After analyzing the quantification method I based on 13 environmental factors to develop the score table for the site-index estimation of Chamaecyparis obtusa Endlicher, $R^2$ value of the model was 0.7555. It has been analyzed that the scope value of Soil moisture in horizon A was 7.5045, that of total soil depth was 6.3896, that of topography was 5.3471, that of slope was 4.7000 and that of aspect was 3.2038. After analyzing the partial correlation to examine the factors that affected most the site-index of Chamaecyparis obtusa Endlicher, it has been noted that the partial correlation of climatic zone was 0.4987, which was highest, and it was followed by Soil moisture in horizon A (0.4592), slope (0.4537), topography (0.3299) and total soil depth (0.1035). As a result of conducting the significance test for partial correlation, it has been found that topography, climatic zone, parent rock, slope, altitude, aspect, Soil moisture in horizon A, soil hardness in horizon A and total soil depth were recognized significant with 1% of significance level and sedimentary type and soil texture in horizon A were recognized significant with 5% of significance level.

A Study on the Distribution Characteristics of Buxus koreana in Kwanaksan Ecological and Scenery Conservation Area (관악산 생태경관보전지역 내 회양목 분포 특성 연구)

  • Lee, Ho-Young;Oh, Choong-Hyeon;Lee, Sang-Jin
    • Korean Journal of Environment and Ecology
    • /
    • v.26 no.1
    • /
    • pp.91-99
    • /
    • 2012
  • The purpose of this study was to find out the vegetation community structure and the distribution characteristics of Buxus koreana through analysis of the topography and soil characteristics in Kwanaksan Ecological and Scenery Conservation Area. To do this twenty two plots as $100m^2$ each were set up and investigated. As a result, the vegetation communities were classified in four groups; Pinus rigida community (I), P. rigida - B. koreana community(II), Quercus mongolica community(III), Quercus acutissima - Quercus serrata community(IV). The distribution characteristics in topography appeared that B. koreana distributed more in valley where soil water and nutrition conditions are good. The drainage condition also influenced the distribution, because the ratio of clay was low in the result of soil texture analysis. B. koreana was distributed in high-pitched slope and the high rock ratio area. According to the soil analysis, the mean soil pH of B. koreana distributed groups(pH 4.79) was higher than that of non-B. koreana distributed groups(pH 4.41). It appeared that B. koreana had tolerance to the barren soil, so the value of exchangeable cations such as $Ca^{2+}$ and $Mg^{2+}$were showed lower than that of the average of Korean forest soil.

Hydrogeochemical Research on the Characteristic of Chemical Weathering in a Granitic Gatchment (水文化學的 資料를 통한 花崗岩質 流域의 化學的 風化特性에 關한 硏究)

  • Park, Soo-Jin
    • Journal of the Korean Geographical Society
    • /
    • v.28 no.1
    • /
    • pp.1-15
    • /
    • 1993
  • This research aims to investigate some respects of chemical weathering processes, espcially the amount of solute leaching, formation of clay minerals, and the chemical weathering rate of granite rocks under present climatic conditions. For this purpose, I investigated geochemical mass balance in a small catchment and the mineralogical composition of weathered bedrocks including clay mineral assemblages at four res-pective sites along one slope. The geochemical mass blance for major elements of rock forming minerals was calculated from precipitation and streamwater data which are measured every week for one year. The study area is a climatically and litholo-gically homogeneous small catchment($3.62Km^2$)in Anyang-shi, Kyounggi-do, Korea. The be-drock of this area id Anyang Granite which is composed of coarse-giained, pink-colored miner-als. Main rock forming minerals are quartz, K-Feldspar, albite, and muscovite. One of the chracteristics of this granite rock is that its amount of Ca and Mg is much lower than other granite rock. The leaching pattern in the weathering profiles is in close reltion to the geochemical mass balance. Therefore the removal or accumulation of dissolved materials shows weathering patterns of granite in the Korean peninsula. Oversupplied ions into the drainage basin were $H^+$, $K^+$, Fe, and Mn, whereas $Na^2+$, $Mg^2+$, $Ca^2+$, Si, Al and $HCO-3^{-}$ were removed from the basin by the stream. The consumption of hydrogen ion in the catchment implies the hydrolysis of minerals. The surplus of $K^+$ reflects that vegetation is in the aggravation stage, and the nutrient cycle of the forest in study area did not reach a stable state. And it can be also presumed that the accumulation of $K^+$ in the top soil is related to the surplus of $K^+$. Oversupplied Fe and Mn were presumed to accumulate in soil by forming metallic oxide and hydroxide. In the opposite, the removal of $Na^+$, Si, Al resulted from the chemical weathering of albite and biotite, and the amount of removal of $Na^+$, Si, Al reflected the weathering rate of the bedrock. But $Ca^2+$ and $Mg^2+$ in stream water were contaminated by the scattered calcareous structures over the surface. Kaolinite is a stable clay mineral under the present environment by the thermodynamical analysis of the hydrogeochemical data and Tardy's Re value. But this result was quite different from the real assemblage of clay miner-als in soil and weathered bedrock. This differ-ence can be explained by the microenvironment in the weathering profile and the seasonal variation of climatic factors. There are different clay forming environments in the stydy area and these differences originate from the seasonal variation of climate, especially the flushing rate in the weathering profile. As it can be known from the results of the analysis of thermodynamic stability and characteristics of geochemical mas balance, the climate during winter and fall, when it is characterized by the low flushing rate and high solute influx, shows the environmental characteristics to from 2:1 clay minerals, such as illite, smectite, vermiculite and mixed layer clay minerals which are formed by neoformation or transformation from the primary or secondary minerals. During the summer and spring periods, kaoli-nite is a stable forming mineral. However it should consider that the other clay minerals can transformed into kaolinite or other clay minerals, because these periods have a high flushing rte and temperature. Materials which are directly regulated by chemical weathering in the weathered bedrock are $Na^+$, Si, and Al. The leaching of Al is, however, highly restricted and used to form a clay mineral, and that of Si falls under the same category. $Na^+$ is not taked up by growing veget ation, and fixed in the weathering profile by forming secondary minerals. Therefore the budget of $Na^+$ is a good indicator for the chemical weathering rate in the study area. The amount of chemical weathering of granite rocks was about 31.31g/$m^2+$/year based on $Na^+$ estimation.

  • PDF

Effects of Soil Hardness on the Root Distribution of Pinus rigida Mill. Planted in Association with Sodding Works on the Denuded Land (사방시공지(砂防施工地)에 있어서 리기다소나무의 수근(樹根)의 분포(分布)에 미치는 토양견밀도(土壤堅密度)의 영향(影響))

  • Cho, Hi Doo
    • Journal of Korean Society of Forest Science
    • /
    • v.56 no.1
    • /
    • pp.66-76
    • /
    • 1982
  • Soil harness represents such physical properties as porosity, amount of water, bulk density and soil texture. It is very important to know the mechanical properties of soil as well as the chemical in order to research the fundamental phenomena in the growth and the distribution of tree roots. The writer intended to grip soil hardness by soil layer and also to grasp the root distribution and the correlation between soil hardness and the root distribution of Pinus riguda Mill. planted on the denuded hillside with sooding works by soil layer on soil profile. The site investigated is situated at Peongchang-ri 13, Kocksung county, Chon-nam Province. The area is consisted of 3.63 ha having on elevation of 167.5-207.5 m. Soil texture is sandy loam and parant rock in granite. Average slope of the area is $17^{\circ}-30^{\circ}$. Soil moisture condition is dry. Main exposure of the area is NW or SW. The total number of plots investigated was 24 plots. It divided into two groups by direction each 12 plots in NW and SW and divided into three groups by the position of mountain plots in foot of mountain, in hillside, and in summit of mountain, respectively. Each sampling tree was selected as specimen by purposive sampling and soil profile was made at the downward distance of 50cm form the sampling tree at each plot. Soil hardness, soil layer surveying, root distribution of the tree and vegetation were measured and investigated at the each plot. The soil hardness measured by the Yamanaka Soil Hardness Tester in mm unit. the results are as follows: 1) Soil hardness increases gradually in conformity with the increment of soil depth. The average soil indicator hardness by soil layer are as follows: 14.6mm in I - soil layer (0-10cm in depth from soil surface), 16.2mm in II - soil layer (10-20cm), 17.2 in III - soil layer (20-30cm), 18.3mm in IV - soil layer(30-40cm), 19.8mm in V - soil layer (4.50mm). 2) The tree roots (less than 20mm in diameter) distribute more in the surface layer than in the subsoil layer and decrease gradually according to the increment of soil depth. The ratio of the root distribution can be illustrated by comparing with each of five soil layers from surface to subsoil layer as follows: I - soil layer; 31%, II - soil layer; 26%, III - soil layer; 18%, IV - soil layer; 12%, V - soil layer; 13%, 3) Soil hardness and tree root distribution (less than 20mm in diameter) of Pinus rigida Mill. correlate negatively each other; the more soil hardness increases, the most root distribution decreases. The correlation coefficients between soil hardness and distribution of tree roots by soil layer are as follows: I - soil layer; -0.3675 (at the 10% significance level), II - soil layer; -0.5299 (at the 1% significance level), III - soil layer; -0.5573 (at the 2% significance level), IV - soil layer; -0.6922 (at the 5% significance level), V - soil layer; -0.7325 (at the 2% significance level). 4) the most suitable range of soil hardness for the growth of Pinus rigida Mill is the range of 12-14.9mm in soil indicator hardness. In this range of soil indicator hardness, the root distribution of this tree amounts to 41.8% in spite of 33% in soil harness and under the 20.9mm of soil indicator hardness, the distribution amounts to 93.2% in spite of 82% in soil hardness. Judging from above facts, the roots of Pinus rigida can easily grow within the soil condition of 20.9mm in soil indicator hardness. 5) The soil layers are classified by their depths from the surface soil.

  • PDF

Basis Research for hazard map and Characteristic inquiry of Slope Failure by Rainfall (강우에 의한 붕괴 절개면 특성 고찰 및 위험도 작성을 위한 기초연구)

  • Yoo, Ki-Jeong;Koo, Ho-Bon;Baek, Yong;Rhee, Jong-Hyun
    • Proceedings of the Korean Geotechical Society Conference
    • /
    • 2003.03a
    • /
    • pp.509-512
    • /
    • 2003
  • Our country is serious difference of precipitation seasonally and about 66% of yearly mean rainfall is happening in concentration rainfall form between September on June. It requires consideration because of a lot of natural disasters by this downpour are produced. Slope failure is happened by artificial factor of creation of slope according to the land development, fill slope etc. and natural factor of rainfall, topography, nature of soil, soil quality, rock floor. Usually, Direct factor of failure slope is downpour. In this study, the Slope about among 55 places happened failure by downpour investigated occurrence position, geological etc and executed and inquire into character of rainfall connected with failure slope. Among character of rainfall, executed analysis about Max. hourly rainfall and cumulative rainfall of place that failure slope is situated and grasped the geological character of failure slope. Through this, inquire to character of failure slope by rainfall and take advantage of basis study for Hazard map creation.

  • PDF