• The Journal of Engineering Geology
• /
• v.27 no.3
• /
• pp.267-274
• /
• 2017

Behavior of rock mass depend on the mechanical properties of intact rock and geometrical property of discontinuity distributed in rock mass. In case of rock slope, particularly, location of slope failure surface and behavior after failure are changed due to discontinuities. In this study, two 3D slope stability analysis methods were developed for two different failure types which are circular failure and planar failure, considering that failure type of rock slope is dependent on scale of discontinuity which was then applied to real rock slope to review the applicability. In case of circular failure, stable condition was maintained in natural dry condition, which however became unstable when the moisture content of the surface was increased by rainfall. In case of planar failure, rock slope become more unstable comparing to dry condition which is attributable to decrease in friction angle of discontinuity surface due to rainfall. Viewing analysis result above, analysis method proved to have well incorporated the phenomenon occurred on real slope from the analysis result, demonstrating its applicability to reviewing the slope stability as well as to maintaining the slope.

• Tunnel and Underground Space
• /
• v.6 no.2
• /
• pp.166-174
• /
• 1996

Stability of rock slope is greatly affected by the geometry and strength of discontinuities developed in the rock mass. In this study an analytical method which is capable of analyzing the effect of relative orientation between the discontinuities and the slope face on the safety of slope by assessing their vector components was used to evaluate the stability and the maximum cut-angle for the proposed slope design. The results of computerized vector analysis revealed that slope area under investigation might be divided into 3 sections of different face directions. The safety factors for benches in each 3 sections were calculated using the limit-equilibrium theory. Then, by utilizing the concept of probabilistic risk analysis, the susceptibility of entire slope failure was estimated. Based on the distribution of safety factor in each bench, the maximum cut angle of each section could be selected differently ot achieve the permanent stability of the entire slope.

• Geomechanics and Engineering
• /
• v.13 no.4
• /
• pp.571-584
• /
• 2017

Slope mass rating (SMR) is commonly used for the geomechanical classification of rock masses in an attempt to evaluate the stability of slopes. SMR is calculated from the $RMR_{89-basic}$ (basic rock mass rating) and from the characteristic features of discontinuities, and may be applied to slope stability analysis as well as to slope support recommendations. This study attempts to utilize the SMR classification system for slope stability analysis and to investigate the engineering geological conditions of the slopes and the slope stability analysis of the Gas Flare site in phases 6, 7 and 8 of the South Pars Gas Complex in Assalouyeh, south of Iran. After studying a total of twelve slopes, the results of the SMR classification system indicated that three slope failure modes, namely, wedge, plane and mass failure were possible along the slopes. In addition, the stability analyses conducted by a number of computer programs indicated that three of the slopes were stable, three of the slopes were unstable and the remaining six slopes were categorized as 'needs attention'classes.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.265-272
• /
• 2001

Excavation in a big city is different from excavation in a local area because construction methods and stability are directly connected in a loss of life. Especially, estimate of rock mass slope stability is excuted by more detail and safty work. In this study, we are made reserches in rock mass slope stability and safety method that the slope is closed by elementary school in a big city. The result of many field study and numerical analysis is shown up direct reinforcement used to anchor.

• Geomechanics and Engineering
• /
• v.8 no.1
• /
• pp.97-111
• /
• 2015

The kinematical approach of limit analysis is used to estimate the three dimensional stability analysis of rock slopes with nonlinear Hoek-Brown criterion under earthquake forces. The generalized tangential technique is introduced, which makes limit analysis apply to rock slope problem possible. This technique formulates the three dimensional stability problem as a classical nonlinear programming problem. A nonlinear programming algorithm is coded to search for the least upper bound solution. To prove the validity of the present approach, static stability factors are compared with the previous solutions, using a linear failure criterion. Three dimensional seismic and static stability factors are calculated for rock slopes. Numerical results of indicate that the factors increase with the ratio of slope width and height, and are presented for practical use in rock engineering.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.5
• /
• pp.61-69
• /
• 2008

In general, it has been usually used the method that assess rock slope stability using stereographic projection method, limit equilibrium analysis, numerical analysis and slope stability evaluation table. Several methods for assessing the stability of rock slopes has been proposed on the basis of site investigation data. These method adopted different evaluation items and weighting factors by researchers, organization and nation. But the researches for each evaluation items were insufficient. So the effectiveness of rock slope stability evaluation items for geometrical configuration (slope height, slope direction and angle, dip and dip direction of major discontinuity, absolute value for the direction difference for slope and major discontinuities) and topographical characteristic (possibility of topographical water concentration, upper natural slope angle, slope configuration) using 315 failure and stable highway rock slope analysis data, AV (abnormal value) analysis and NMAV (normalized maximum abnormal value) analysis were evaluated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.11b
• /
• pp.103-114
• /
• 2002

Stability of cut-slope is considered to have a deep relationship with rock types since rock has its own engineering and geological characteristic such as shear strength, durability, weathering profile, geological structures. Therefore, analysis of geological and engineering characterisics of rock mass is essential for the evaluation of rock slope stability This paper introduces the statistical data of slope failure cases which was collected from highway slopes constructed in sedimentary rock mainly of shale in Ky ng-sang Basin. Primary failure feature in this area is planar failure along the bedding regardless of slope geometry. Even a disasterous slope failure case due to the thick clay layer between the beddings was reported. Failures and rock fall were reported to ocurred frequently after the completion of cutting due to the weathering, so long-term slope stability should be considered as a important factors in design.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.167-174
• /
• 2000

Profiles of discontinuities through scanline method were investigated for the analysis of rock slope stability. Lower hemispheric projection method was used to evaluate the geometric stability and failure potential of these discontinuities. Also, safety factor was evaluated for the discontinuities of failure potential using by limit equilibrium analysis. Then, displacements of rock block due to the discontinuities were displayed by using the program UDEC(Universal Distinct Element Code) which applied the Distinct Element Method. When we determine the cut-slope in design, the characteristics of discontinuities is not represented only by strength parameters of intact rock. Therefore it is more reasonable method in assuring stability that first, construction would be preceded by the cut-slope of preliminary design, and then, cut-slope would be redetermined by elaborate site investigation in processing construction.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.551-558
• /
• 2000

When cut slope is excavated, corestone in cut slope exists 20∼30%. In case of soil and soft rock mixing, people lay out gradient of 1 : 0.5, because of soft rock slope. In a case, slope that exists corestone between soil happens to large landslide. So, As a study performs geological survey, Analysis of slope stability reinforcement measures, etc, A study presents example meaures and analysis on slope stability of corestone.

• Geomechanics and Engineering
• /
• v.10 no.1
• /
• pp.59-76
• /
• 2016

The non-linear Hoek-Brown failure criterion has been widely accepted and applied to evaluate the stability of rock slopes under plane-strain conditions. This paper presents a kinematic approach of limit analysis to assessing the static and seismic stability of three-dimensional (3D) rock slopes using the generalized Hoek-Brown failure criterion. A tangential technique is employed to obtain the equivalent Mohr-Coulomb strength parameters of rock material from the generalized Hoek-Brown criterion. The least upper bounds to the stability number are obtained in an optimization procedure and presented in the form of graphs and tables for a wide range of parameters. The calculated results demonstrate the influences of 3D geometrical constraint, non-linear strength parameters and seismic acceleration on the stability number and equivalent strength parameters. The presented upper-bound solutions can be used for preliminary assessment on the 3D rock slope stability in design and assessing other solutions from the developing methods in the stability analysis of 3D rock slopes.