• 마이크로전자및패키징학회지
• /
• 제10권2호
• /
• pp.39-47
• /
• 2003

감광성 폴리이미드 위에 Cr을 RF 바이어스 스퍼터링 및 RF클리닝 후 DC 스퍼터링한 Cr/폴리이미드의 계면을 TEM으로 관찰하였다. RF power 밀도를 $0.13W/cm^2$에서 $2.12W/cm^2$로 증가시키면서 RF클리닝을 실시한 결과 폴리이미드의 에칭 양상이 둥근 모양에서 뾰족한 모양으로 변하였고 이방성 에칭으로 인해 거칠기가 크게 증가하였다. RF 바이어스 스퍼터링의 경우 RF power를 올리는 동안 RF 클리닝에 의해 폴리이미드가 에칭되었고, 에칭된 부분에 Cr이 증착된 계면을 단면으로 관찰한 결과 Cr과 폴리이미드가 겹쳐져서 혼합된 것처럼 보였다. 그러나 RF power를 올리는 시간을 단축시켜 Cr을 바이어스 스퍼터링했을 때에는 계면이 분명하게 관찰되어 Cr의 implantation이 일어나지 않았음을 알 수 있었다. RF 클리닝한 Cu/Cr/Polyimide를 필 테스트한 결과 짧은 시간의 RF 클리닝으로도 접착력이 크게 증가하였다. 그러므로 RF power를 올리는 동안 실시되었던 RF 클리닝이 RF 바이어스 스퍼터링한 Cr/Polyimide의 접착력 향상에 영향을 주었을 것으로 예상된다.

• 한국전기전자재료학회논문지
• /
• 제25권12호
• /
• pp.979-983
• /
• 2012

We proposed the ZnO thin film for a SAW filter by PLD and RF sputtering method. ZnO thin films was pre-deposited on a sapphire substrate as a seed layer by PLD method and then deposited on seed layer by RF sputtering. The surface characteristics of ZnO thin film were investigated by XRD, SEM and AFM. The minimum surface roughness was 1.92 nm and FWHM of rocking curve was $0.92^{\circ}$. We demonstrated the SAW filter with bandwidth of approximately 0.97 MHz and the center frequency of 18.72 MHz using the proposed ZnO thin film.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권2호
• /
• pp.196-203
• /
• 1996

The highly c-axis oriented zinc oxide thin films were deposited on Sapphire(0001) substrates by reactive RF magnetron sputtering. The characteristics of zinc oxide thin films on RF power, substrate-target distance, and substrate temperature were investigated by XRD, SEM and EDX analyses. The physical characteristics of zinc oxide thin films changed with various deposition conditions. The higher substrate temperatures were, The better crystallinity of zinc oxide thin films. The highly c-axis oriented zinc oxide thin films were obtained at sputter pressure 5mTorr, rf power 200W, substrate temperature 350.deg. C, substrate-target distance 5.5cm. In these conditions, the resistivity of zinc oxide thin films deposited on pt/sapphire was 12.196*10$^{9}$ [.ohm.cm].

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.289-292
• /
• 1997

BaTiO$_3$thin film capacitor were prepared on Pt(100)/SiO$_2$/Si(100)wafer by RF sputtering technique. Dielectric and electrical characteristics of the thin film capacitor are investigated. The Dielectric constant and loss were about 683 and 5[%], respectively. We found that the leakage current of thin film capacitor is depend on RF power during deposition. Because of increase of activation energy, leakage current inclosed at high RF power and sheet resistivity of the films was decreased. Swithching voltage of thin film capacitor was 4.4[V]

• Journal of Korean Vacuum Science & Technology
• /
• 제2권2호
• /
• pp.133-138
• /
• 1998

To enhance the ionization level of I-PVD and reduce the coil voltage two approaches were tried and as a diagnostic, optical emission spectroscopy and impedance analysis of the plasma was done with a range of Ar pressures and RF power along with XRD analysis of deposited Ag films. RF sputtering power was pulsed with various on/off time scales to recover the ICP quenched by sputtered metals. This in average enhances the ionization of the sputtered atoms with 10 ms/10 ms and 100 ms/100ms pulse on/off time duration and gives higher (200) preferred orientation over (111) in deposited Ag films. Secondly, Small axial B field about 8G remarkably reduced RF coil sputtering and showed scaled relationship between RF power and magnetic field strength for optimal process condition. From OES of Ar0 and Ar+, wave-like dispersion structure appeared and reduced the coil voltage about 20% at very weak field strength of 8G. This should be studied further to have nay relation with low mode helicon wave launching.

• Transactions on Electrical and Electronic Materials
• /
• 제15권6호
• /
• pp.328-332
• /
• 2014

Thin film transistors (TFTs) with an amorphous silicon zinc tin oxide (a-2SZTO) channel layer have been fabricated using an RF magnetron sputtering system. The effect of the change of excitation electron on the variation of the total interfacial trap states of a-2SZTO systems was investigated depending on sputtering power, since the interfacial state could be changed by changing sputtering power. It is well known that Si can effectively reduce the generation of the oxygen vacancies. However, The a-2SZTO systems of ZTO doped with 2 wt% Si could be degraded because the Si peripheral electron belonging to a p-orbital affects the amorphous zinc tin oxide (a-ZTO) TFTs of the s-orbital overlap structure. We fabricated amorphous 2 wt% Si-doped ZnSnO (a-2SZTO) TFTs using an RF magnetron sputtering system. The a-2SZTO TFTs show an improvement of the electrical property with increasing power. The a-2SZTO TFTs fabricated at a power of 30 W showed many of the total interfacial trap states. The a-2SZTO TFTs at a power of 30 W showed poor electrical property. However, at 50 W power, the total interfacial trap states showed improvement. In addition, the improved total interfacial states affected the thermal stress of a-2SZTO TFTs. Therefore, a-2SZTO TFTs fabricated at 50 W power showed a relatively small shift of threshold voltage. Similarly, the activation energy of a-2SZTO TFTs fabricated at 50 W power exhibits a relatively large falling rate (0.0475 eV/V) with a relatively high activation energy, which means that the a-2SZTO TFTs fabricated at 50 W power has a relatively lower trap density than other power cases. As a result, the electrical characteristics of a-2SZTO TFTs fabricated at a sputtering power of 50 W are enhanced. The TFTs fabricated by rf sputter should be carefully optimized to provide better stability for a-2SZTO in terms of the sputtering power, which is closely related to the interfacial trap states.

• 한국진공학회지
• /
• 제5권2호
• /
• pp.139-146
• /
• 1996

rf 마그네트론 스파터링법을 이용하여 투명 전도성 Sb-doped $SnO_2$ 박막을 증착하였으나 박막표면에서 막손상현상이 발생하였다. 특히 기판 중심부 및 타게트 부식부위에 대응하는 부분에서 발생된 막손상을 방지하고자 , 환원형의 마스크 유리가 타게트표면에서 1.5cm지점에 설치되었다. 또한 마그네트론 스파터링의 작동조건인 rf전력, 스파터링 가스압력 및 기판온도를 최적으로 조절하면서 박막의 균일성과 전기적 특성을 평가하였다. 작동조건을 이용한 실험결과에서 균일하고 막손상이 없는 박막을 증착하는 최적온도는 압력 변화에 따라 변하며, 비율은 50w의 rf전력에서 5mTorr당 약 $100^{\circ}C$정도였다. 유사하게 rf 전력？ md가에 대한 보상에서 최적온도는 적절한 비율로 내려간다.

• 한국세라믹학회지
• /
• 제35권5호
• /
• pp.472-478
• /
• 1998

Ferroelectric SrBi2Ta2O9(SBT) films were deposited on Pt/Ti/SiO2/Si substrates at 50$0^{\circ}C$ using a sintered SBT target Bi and Ta targets by modified rf magnetron sputtering and then were annealed at 80$0^{\circ}C$ for 10min in oxygen ambinet(760 torr) The composition of the SBT films could be easily controlled using the mul-ti-targets. The film composition of {{{{ {Sr }_{0.8 } {Bi }_{2.9 } {Ta}_{2.0 } {O }_{9 } }} was obtained with SBTd sputtering power of 100 W Bi of 25W and Ta of 10 W. A 250nm thick SBT films exhibited a dense and uniform microstructure and showed the remanent polarization(Pr) of 14.4 $\mu$C/cm2 and the coercive field({{{{ {E }_{c } }})of 60 kV/cm at applied voltage of 5 V. The SBT films show practically no polarization fatigue up to {{{{ {10 }_{10 } }} cycles under 5V bipolar pulse. The retention characteristics of the SBT films looked very promising and the leakage current density of the SBT films was about 1.23$\times${{{{ {10 }^{-7 } }}A/c{{{{ {m }^{2 } }} at 120kV/cm.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권7호
• /
• pp.706-712
• /
• 1997

AlN(Aluminium Nitride) thin films were prepared using by RF sputtering method on the Si(100) and Si(111) substrates as the parameters of the substrate temperature, RF power, sputtering duration and the $N_2$/Ar ratio and investigated by X-ray diffraction, IR spectrometry, n&k analyzer. For the Si(100) substrate, the AlN thin films of (101) orientation were obtained under the conditions of room temperature and the nitrogen of 60 vol.%. For the Si(111) substrate, the (002) AlN thin films were obtained under the nitrogen of 100 vol.%. In case of the thin film prepared in the condition of above 60 vol.% of the nitrogen, the average value of the surface roughness of the film was 151$\AA$. From the changes of the half widths of E$_1$[TO] phonon bands at the wavenumber of 680$cm^{-1}$ /, it were compared of the crystallinities of the films which were grown under the different conditions. The thicknesses of AlN films were decreased dramatically in the region of the nitrogen of 40~60 vol.%. Its due to the nitridation of the Al target surface and getting low of the sputtering yield by the $N_2$/Ar ratio being increased.

• 한국전기전자재료학회논문지
• /
• 제27권8호
• /
• pp.510-515
• /
• 2014

Thin films of cubic $Na_{0.6}WO_3$, which is one of the sodium tungsten bronze, were fabricated by rf sputtering for the electrode applications in integrated sensors and actuators. A single-phase cubic $Na_{0.6}WO_3$ sputtering target of power type was prepared by conventional solid-state reaction. Thin films were deposited from the powder target, and the as-deposited films were amorphous, thus they annealed by tube furnace or RTP for crystallization. Thin films having cubic phase $Na_xWO_3$ were fabricated by the optimization of sputtering and post-annealing conditions, but single-phase cubic $Na_{0.6}WO_3$ thin films were not obtained. Although the films were not in single phase, they had good electrical conduction properties showing electrical resistivities of $10-4{\Omega}{\cdot}cm$ order.