Leaves of Aloe vera Linne and bloods of domestic animal were composted in a soild state fermentation reactor (SSFR) by using microbial additive including a bulking and moisture controlling agent. From solid-culture of microbial additive, 10 species of bacteria and 10 species of fungi were isolated and, their enzyme activities including amylase, carboxy methyl cellulase CMCase, lipase and protease were detected. Optimum fermentation conditions of Aloe leaves and domestic animal bloods in SSFR were obtained from the studies of response surface analysis employing microbial additive content, initial moisture content, and fermentation temperature as the independent variables. The optimum conditions for SSFR using Aloe leaves were obtained at 9.45$\pm$73%(w/w) of microbial additives, 62.73$\pm$4.54%(w/w) of initial moisture content and 55.32$\pm$3.14$^{\circ}C$ of fermentation temperature while those for SSFR using domestic animal bloods were obtained at 10.25$\pm$2.04%, 58.68$\pm$4.97% and 57.85$\pm$5.$65^{\circ}C$, respectively. Composting process in SSFR was initially proceeded through fermentation and solid materials were decomposed within 24 hours by maintaining higher moisture level, and maturing and drying steps are followed later. After the fermentation step, the concentrations of solid phase inorganic components were increased while that of organic components were decreased. Also, concentrations of total organic carbon(TOC), peptides, amino acids, polysaccharides, and low fatty acids in water extracts were increased. As fermentation in composting process depends on initial C/N ratios in water extracts of two samples were increased because of increased water-soluble TOC. From these results, it was revealed that solid state fermentation reactor using microbial additives can be used in composting process of organic wastes with broad C/N ratio.
Alkaline peroxide bleaching of (chemi) mechanical pulp is a very complicated system where various process factors affect the bleaching performance and pulp properties. Traditional on-factor-at a time method is ineffective and costly in finding the optimal bleaching conditions. In this study statistical experimental methods which include three steps. I. e. screening, response surface modeling and optimization, were used to find the conditions for maximal brightness development during one stage alkaline peroxide bleaching of TMP which had an initial brightness of 54.5% Elerpho. The TMP was pretreated with EDTA(0.5% on O. D. pulp. consistency, $30^{\circ}C$ for 60 minutes) and bleached in a 2L Mark V Quantum Reactor at 750rpm, 7.5% of bleaching consistency and with 0.05% magnesium sulfate addition. The ranges of other factors studied were 1~5% hydrogen peroxide on O. D plup, 1~4% sodium hydroxide on O. D pulp and 1~4% sodium silicate on O. D pulp, reaction temperature 50~$90^{\circ}C$ and reaction time 40~180minutes. A models with good predictability was established and the maximal brightness after one stage bleaching was found to be 70% Elerpho at $50^{\circ}C$, 50 minutes 5% hydrogen peroxide on O. D. pulp 3.2~3.4% sodium hydroxide on O. D. pulp 3.2~3.4% sodium hydroxide on O. D pulp and 4% silicate on O. D pulp. However further studies on other pulp properties such as strength and brightness stability shall be carried out in order to find out the optimal bleaching conditions.
Bellows are mechanical components which prevent the damage of system by absorption of the vibration and the displacement of axle and radial direction. Thermal piping system is expanded by the fluid of the high temperature from the heat engine inside. At this time, bellows prevent the damage of the piping due to the thermal expansion. Recently, design of bellows is required to fit some other operational environments which are not suggested in the E.J.M.A code book. And it is difficult to produce and to maintain bellows of high temperature and high pressure bemuse of its complicated shape and this causes the manufacturing cost to rise. The objective of this study is to determine optimum shape of bellows which can endure in the high temperature and high pressure. The maximum stress has an effect on the fatigue life of bellows, therefore it needs to be minimized. This study attempts to find a shape which minimizes the stress occurring in the bellows by the design of experiment. The model used in this study is not presented in the E.J.M.A code book, therefore, from the result of design of experiment we find the factors which give effects on the characteristic value and we presents the recession model using the RSM, which can predict the characteristic values depending on the change of factor values.
In this study, we aimed to develop a mixed tea prepared with roasted mulberry leaf and fruit using response surface methodology (RSM). Roasting of mulberry leaf was by 6 stages, as shown in Fig. 1; and mulberry fruit was roasted in 4 stages, as shown in Fig. 2. Subsequently, physicochemical measurements such as total polyphenol content, nitric oxide production content, and ${\alpha}$-glucosidase inhibitory effect were obtained for each sample. Central composite design was applied to prepare samples containing varying contents of roasted mulberry leaf (RoML) and roasted mulberry fruit (RoMF); subsequently, sensory evaluation was conducted. The total polyphenol content of roasted samples (RoML and RoMF) were significantly higher than that of raw samples (RaML and RaMF), respectively. The nitric oxide (NO) production of roasted samples were significantly lower than that of control (LPS induced RAW 264.7 cell). The ${\alpha}$-glucosidase inhibitory effect of roasted samples was significantly higher than that of raw samples, respectively. Based on the RSM estimation for determination of optimum ratio by sensory evaluation (taste, color, and flavor) among 13 mixed samples, the optimum mixing ratio of RoML and RoMF for taste, color, and flavor were 1.64 g (RoML) and 0.88 g (RoMF), 1.35 g (RoML) and 0.92 g (RoMF), 1.65 g (RoML) 1.03 g (RoMF), respectively. Based on results of three sensory evaluations, mixing ratio comprising 1.54 g of RoML and 0.92 g of RoMF is desirable for delicious tea with functionality.
전투기의 개념설계 과정에서는 기준형상 도출을 위해 비교분석연구가 반복된다. 반복적인 비교분석연구가 자동화되면 효율적으로 기준형상을 도출할 수 있다. 본 연구에서는 비교분석연구의 자동화를 위한 성능해석 프로그램을 개발했다. 프로그램은 형상생성모듈과 중량예측모듈, 임무성능 해석모듈로 구성된다. 형상생성모듈을 사용하여 3D CAD 모델 생성이 가능하며 중량예측모듈에서는 경험식을 사용하여 중량을 예측한다. 임의의 임무형상에 대한 임무성능 해석이 가능하며 최적화 기법을 사용하여 최적 임무성능 계산이 가능하다. 개발된 프로그램의 검증을 진행하여 개념설계 단계에 적용 가능함을 확인했다.
Response surface methodology (RSM) was successfully applied to optimize for the production of Ganoderma lucidum in batch fermentations using the whey (40,000 mg latose/L) as substrate. This study was performed according to the central composite design (CCD) with respect to pH and temperature, where the designed intervals were 3.3$22.9^{\circ}C$$37.1^{\circ}C$, respectively. A second-order factorial design of the experiments was used to build empirical models providing a quantitative interpretation of the relationships between the two variables. The optimum conditions to maximize the production of G. lucidum were pH 4.2 and $28.3^{\circ}C$. At optimum conditions, the mycelial dry weight (MDW) and residual soluble COD (SCOD) were simultaneously used to evaluate the biokinetic coefficients assocoated with substrate inhibition model by nonlinear least squares method with 95% confidence interval. The. maximum microbial growth rates (${\mu}m$), half saturation coefficient ($K_s$), and the inhibition substrate concentration ($K_{is}$) were determined to be 0.095 l/hr, 128,000 mg SCOD/L and 49,000 mg SCOD/L, respectively. And the microbial yield coefficient (Y), biomass decay rate coefficient ($K_d$), and the maintenance energy coefficient ($m_s$) were determined to be 0.37 mg MDW/mg SCOD, 0.001 1/hr, and 0.0015 1/hr, respectively.
본 연구에서는 갑각류의 껍질로부터 추출한 chitosan으로부터 황산을 촉매로 사용하여 가수분해 및 에스테르화 반응과 반응표면분석 실험계획법을 적용하여 화학 원료 및 연료로 사용 가능한 ethyl levulinate의 생산 가능성을 조사하였다. 반응물 중 수분함량의 영향을 조사한 결과, chitosan의 가수분해와 동시에 탈수반응과 ethyl levulinate로의 에스테르화와 반응은 5% 수분함량에서 가장 높았다. 반응표면분석 실험계획법을 이용하여 반응인자를 최적화한 결과, 200 ℃, 3.19% chitosan, 0.49M 황산 촉매, 5% 수분함량(95% 에탄올 용매), 그리고 58분의 반응조건에서 30.1%의 ethyl levulinate의 생성 수율을 얻었다. 또한, ethyl levulinate의 생성 수율은 반응의 가혹도가 증가할수록 증가하는 경향을 나타내었다. 이러한 결과는 chitosan이 화학 원료 및 연료의 생산에 사용될 수 있는 바이오매스로서의 잠재력이 있다고 판단된다.
현장의 GMA 용접기는 일반적으로 용접기 본체로부터 와이어 송급장치까지의 거리가 약 50m 정도 떨어져 있고 송급장치로부터 토치까지의 거리는 약 3~5m 정도이다. 특히 국산 GMA 용접기의 와이어 송급장치는 DC 모터의 일종인 프린트모터를 사용하고 있으며 제어기는 오픈루프 제어를 하고 있다. 따라서 와이어 송급속도의 변동을 보상할 수 있는 어떤 수단도 장착되어 있지 않다. 또한 송급장치와 토치간 와이어를 안내하는 케이블 도관의 마찰 때문에 토치 끝단에서의 와이어 송급속도가 불규칙해질 수밖에 없다. 용접 시 와이어 송급속도의 순간적인 변동 때문에 용접부의 전류 파형이 매우 불규칙해지고 이 때문에 용융된 용적이 용융풀로 이행하지 못하고 스패터로 비산하는 현상을 발생시킨다. 본 연구에서는 이를 해결하고자 국산 SCR 용접기 및 인버터 용접기와 호환 가능한 디지털 제어형 와이어 송급장치와 Push-Pull 용접 토치를 개발하였다. 또한, 개발된 시스템을 이용하여 정 역 방향 제어기술을 적용하였고 아크 발생 시의 스패터 최소화 공정을 제안하였다. 실험은 SM490A 강재를 사용하여 BOP(Bead On Plate) 용접을 실행하였다. 용접 중 LabVIEW를 이용하여 아크 발생 초기 전류, 전압 그리고 와이어 송급속도를 측정하였고, 고속 카메라를 이용하여 용접현상을 분석하였다. 본 연구를 통해 아크 발생 초기의 스패터를 최소화하는 공정을 도출할 수 있었다. 용접공정 변수인 아크 발생 초기의 와이어 송급속도, 와이어의 역송급 진행거리 그리고 역송급 판단 시점의 용접 전류 값은 실험을 통해 얻을 수 있었다. 또한, 이 연구를 통해 개발된 시스템의 성능을 평가하였다.
Due to the fast response to algae bloom issue in drinking water treatment plant, very fast determination methodology for algal toxin is required. In this study, column switching technique based online preconcentration method was combined with high resolution full scan mass spectrometer to save sample preparation time and to obtain fast and accurate result. After parameter optimization of online preconcentration, 1mL filtered sample was directly injected to trap column with switching valve system. Next, target toxins are eluted by 98% acetonitrile and analysed with 150 - 1,100 amu scan range at 50,000 resolving power. Method detection limit (MDL) for microcystin-LR, the most toxic isomer, was 0.1 ng/mL and others such as microcystin-YR, microcystin-RR and nodularin were 0.08, 0.03 and 0.04 ng/mL, respectively. This is the best improved sensitivities with 1mL volume in the literature. Furthermore, due to the use of ultra pressure HPLC (UPLC), the whole method run was completed in 4 min. Real sample applications for 173 sample including 55 surface water and 118 treatment plant samples for raw and treated water could be done within 16 hours. In our calculation, this methodology is roughly 80% faster than the previous manual solid-phase extraction with LC-MS/MS method.
본 연구에서 탑승자 머리 보호를 위한 센터 필라 트림의 리브 패턴 최적설계는 두 가지 방법에 의해 수행된다. 첫째는 실험계획법과 반응표면법을 이용한 근사최적화 기법으로써, 상대적으로 큰 비중을 차지하는 해석비용 저감을 위하여 근사모델 구성에 필요한 최소한의 해석만을 수행하고 실제 최적화 과정에는 구성된 모델을 이용함으로써 근사적으로 최적 점을 찾아가는 방법이다. 하지만 이러한 방법은 시행착오적인 반복과정을 거쳐야 하는 단점이 있다. 따라서 저자들의 선행연구에서 제안한 순차적 실험계획법과 인공신경망을 이용하여 인자의 상한 또는 하한에 걸리지 않는 근사최적 해를 체계적인 반복과정을 통해 도출하고자 하며, 이를 수학적인 예제와 구조물 문제에 적용함으로써 실용성을 확인하고자 한다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.