• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.189-196
• /
• 2012

This paper proposes new phase error compensation method of RVDT encoder in the FFT domain. Phase errors are measured with a small combination of compensation resistors and the changes of first order coefficients of FFT for each resistor are obtained. It is found that the coefficient change is inversely proportional to the inserted resistor. The proposed method takes less time and the size of the table is smaller than previous time domain approaches. In addition, the location of the compensation resistor can be found through axis transformation of the coefficients. Finally, the peak-to-peak phase error was improved to 0.57 which is two times better than previous one.

• Journal of Sensor Science and Technology
• /
• v.16 no.6
• /
• pp.475-483
• /
• 2007

This paper proposes a readout integrated circuit (ROIC) for $32{\times}32$ infrared focal plane array (IRFPA) detector, which consist of reference resistor, detector resistor, reset switch, integrated capacitor and operational amplifier. Proposed ROIC is designed using $0.35{\;}{\mu}m$ 2P-4M (double poly four metal) n-well CMOS process parameters. Low noise folded cascode operational amplifier which is a key element in the ROIC showed 12.8 MHz unity-gain bandwidth and open-gain 89 dB, phase margin $67^{\circ}$, SNR 82 dB. From proposed circuit, we gained output voltage variation ${\Delta}17{\};mV/^{\circ}C$ when the detector resistor varied according to the temperature.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.376-378
• /
• 1995

A method is presented for the design and fabrication of the temperature compensation circuits on the Clark electrodes for measuring the dissolved oxygen(DO) concentration. The discussion includes a method of the sensor interface circuits for the DO sensor. Typical polarograms for the DO probes under test using this sensor circuits are presented. High accuracy over 99 % of the I to V conversion using the proposed circuit is verified. Temperature dependence for the test DO probe is well compensated automatically using the thermistor($2k\Omega,\;25^{\circ}C$) in series with correction resistor in the feedback loop of the op-amp circuit in the temperature range of the 0-50$^{\circ}C$.

• The Journal of Korea Robotics Society
• /
• v.17 no.2
• /
• pp.152-158
• /
• 2022

As various mobile robots and manipulator robots have been commercialized, robots that can be used by individuals in their daily life have begun to appear. With the development of robots that support daily life, the interaction between robots and humans is becoming more important. Manipulator robots that support daily life must perform tasks such as pressing buttons or picking up objects safely. In many cases, this requires expensive multi-axis force/torque sensors to measure the interaction. In this study, we introduce a low-cost two-axis pressure sensor that can be applied to manipulators for education or research. The proposed system used three force sensitive resistor (FSR) sensors and the structure was fabricated by 3D printing. An experimental device using a load cell was constructed to measure the biaxial pressure. The manufactured prototype was able to distinguish the +-x-axis and the +-y-axis pressures.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.4
• /
• pp.338-347
• /
• 2021

In this paper, the beta-ray sensor circuit used in the true random number generator was designed using DB HiTek's 0.18㎛ CMOS process. The CSA circuit proposed a circuit having a function of selecting a PMOS feedback resistor and an NMOS feedback resistor, and a function of selecting a feedback capacitor of 50fF and 100fF. And for the pulse shaper circuit, a CR-RC2 pulse shaper circuit using a non-inverting amplifier was used. Since the OPAMP circuit used in this paper uses single power instead of dual power, we proposed a circuit in which the resistor of the CR circuit and one node of the capacitor of the RC circuit are connected to VCOM instead of GND. And since the output signal of the pulse shaper does not increase monotonically, even if the output signal of the comparator circuit generates multiple consecutive pulses, the monostable multivibrator circuit is used to prevent signal distortion. In addition, the CSA input terminal, VIN, and the beta-ray sensor output terminal are placed on the top and bottom of the silicon chip to reduce capacitive coupling noise between PCB traces.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.99-100
• /
• 2016

In a AC motor used by three phase inverter, the phase current must be measured to control instantaneous torque. It is expensive to use current sensor for measuring current in low cost motor. So, shunt resistor is used to measure current. But, the method sensing the phase current using shunt resistor cannot perform the vector control in high speed because of the area that impossible to restore three phase current. In this paper, predictive current is proposed for reconstructing the current in the impossible current sensing area that reduce the current ripple in TSSI(Three shunt sensing inverter) for PMSM.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.228-229
• /
• 2009

$VO_2$ thermistor was fabricated on $Al_2O_3$ substrate. and has a CTR (Critical Temperature Resistor) characteristic. $VO_2$ thermistor has a about $10^6$ resistance($\Omega$) in normal temperature. But When temperature is a about $80^{\circ}C$, Resistance of $VO_2$ thermistor is a about some hundred resistance: The resistance of $VO_2$ thermistor increased with increasing length and decreasing width.

• Journal of Mechanical Science and Technology
• /
• v.17 no.11
• /
• pp.1650-1658
• /
• 2003

This paper deals with a novel shunt circuit, which is capable of suppressing multimode vibration amplitudes by using a pair of piezoceramic patches. In order to describe the characteristic behaviors of a piezoelectric damper connected with a series and a parallel resistor-negative capacitor branch circuit, the stiffness ratio and loss factor with respect to the non-dimensional frequency are considered. The mechanism of the shunt damper is also described by considering a shunt voltage constrained by shunt impedance. To obtain a guideline model of the piezo/beam system with a negative capacitive shunting, the governing equations of motion are derived through the Hamilton's principle and a piezo sensor equation as well as a shunt-damping matrix is developed. The theoretical analysis shows that the piezo/beam system combined with a series and a parallel resistor-negative capacitor branch circuit developed in this study can significantly reduce the multiple-mode vibration amplitudes over the whole structural frequency range.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.782-784
• /
• 2002

Many compound semiconductors which have high carrier mobility and small band gap have attentive in application of various practical a field. Especially, InSb served for Hall device and magnetic resistor such as magnetic sensor because InSb thin film has high mobility. Many studies on InSb thin film deposition because In and Sb has been very different feature of vapor pressure($10^4$ times) When In and Sb deposited. In this paper studied it In and Sb deposited simultaneously using by method of co-sputtering deposotion. This process, get to effects of manufacture process simplification. After that this paper observed micro structure and electronic behavior of InSb thin film using by co-sputtering.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.202-207
• /
• 2002

This paper deals with a novel shunted actuator, which has a capability to suppress multi-mode vibration amplitudes by using a pair of piezoceramic patches. In order to describe the characteristic behaviors of shunted dampers connected with a series and a parallel resistor-negative capacitive branch circuit, the stiffness ratio and loss factor with respect to the non-dimensional frequency are considered. To obtain a guideline model of a piezo/beam system connected with a series and a parallel resistor-negative capacitor branch circuit, the governing equations of motion is derived through Hamiltons principle and a piezo sensor equation as well as a shunt damping matrix is developed. The theoretical analysis shows that the shunted actuator developed in this study can significantly reduce multiple-mode vibration amplitudes simultaneously over the whole structural frequency range.