• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.11
• /
• pp.596-602
• /
• 2016

Potassium iodide (KI) TRO sensor for measuring total residual oxidant which is an index for disinfection and neutralization in ballast water has been constructed. The results of UV absorption wavelength and absorbance test in various TRO concentrations show high linear correlation ($r^2=0.9825$) at 350 nm wavelengths and it can be possible to visualize numerical value of TRO concentration (0.1~7.0 mg/L). The result of comparison test according to TRO concentration between the KI based TRO sensor system and the DPD based TRO sensor system showed identical trend. Overall results indicated that the KI TRO sensing system could be applied for continuous TRO concentration measurement in ballast water treatment system.

• Resources Recycling
• /
• v.12 no.6
• /
• pp.26-31
• /
• 2003

The power loss characteristics of Mn-Zn ferrite were observed with the sintering temperature. In case of $1150 ^{\circ}C$ sintering, the core loss increased with measuring temperature, and does not have minimum value at the point where the magnetocrystalline anisotropy be 'zero'. This reason mainly due to the change of core loss mechanism with grain size which affects residual loss. The grain size and sintered density slightly increased with equilibrium oxygen partial pressure at$ 1150 ^{\circ}C$ sintering. The resistivity and initial permeability showed no significance with atmosphere, these results due to complex effect of $Fe^{2+}$ concentration and microstructure change. The core loss at $100^{\circ}C$ decreased as the equilibrium oxygen partial pressure increased.e increased.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.363-368
• /
• 1999

Y-5a-Cu-O superconductors were prepared by TSMG (Top-Seeded Melt Growth) process with multiseeding technique. By using several seeds at the same time, large samples could be fabricated in a short time with simple heat treatment. However, the samples fabricated by normal multiseeding technique show the rapid decrease of trapped magnetic field value across the grain boundaries because of the residual liquid layer. To remove the residual liquid layer, modified multiseeding was newly suggested. The individual grains were combined as single domain, and did not show deterioration of magnetic property at the boundary. The formation mechanism of a well-combined domain by multiseeding technique was discussed.

• Progress in Superconductivity
• /
• v.10 no.2
• /
• pp.87-91
• /
• 2009

Fluorine-doped $SmFeAsO_{1-x}F_x$ single crystals with the nominal value of x=0.2 were grown at $1350-1450^{\circ}C$ under the pressure of 3.3 GPa by using the self-flux method. Plate-shaped single crystals in the range of a few-150 ${\mu}m$ in their lateral size were obtained. The detailed crystal structure was analyzed by using the x-ray diffractometry. Superconducting transition temperature, determined by the resistive transition, of a single crystal was about 49 K with a narrow resistive transition width of ${\sim}1$ K. A relatively sharp transition, a low residual resistivity, and a large residual resistivity ratio compared with those reported for $REFeAsO_{1-x}F_x$(RE=Sm, Nd) single crystals indicate the high quality of our single crystals.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.4
• /
• pp.322-330
• /
• 2015

As a new technical approach, a hydraulic and magnetic clamp device was developed to realize a magnetic clamp crane system by simultaneously actuating eight individual hydraulic cylinders. In this approach, an Sr-type of ferritic permanent magnet (SrO· 6Fe₂O₃), rather than the previous electromagnet, was utilized for the purpose of lifting and transporting the large curved steel plates used for manufacturing ships. This study had the goal of developing and manufacturing a hydraulic, magnetic clamp prototype composed of three main parts, including the base frame, cylinder joint, and magnet joint, in order to safely transport curved steel plates. Furthermore, this research included a performance evaluation of the manufactured prototype and acquired the purposed quantity value in the performance test. The most significant item, the magnetic adhesive force (G), was evaluated in a performance test, which utilized a ferritic permanent magnet (Sr type) with 3700~4000 G of residual induction (Br) and 2640/2770 Oe of coercive force (Hc). In particular, relevant items such as the hoist tension (kN), transportation time (s), and applied load (Kgf) on the hydraulic cylinders were also evaluated in order to determine the optimum values.

• Journal of Korean Society of Forest Science
• /
• v.106 no.2
• /
• pp.213-218
• /
• 2017

The purpose of this study was to develop age-biomass model in Chungnam region containing random effect. To develop the biomass model by species and tree component, data for Pinus densiflora in central region is collected to 30 plots (150 trees). The mixed model were used to fixed effect in the age-biomass relation for Pinus densiflora, with random effect representing correlation of survey area were obtained. To verify the evaluation of the model for random effect, the akaike information criterion (abbreviated as, AIC) was used to calculate the variance-covariance matrix, and residual of repeated data. The estimated variance-covariance matrix, and residual were -1.0022, 0.6240, respectively. The model with random effect (AIC=377.2) has low AIC value, comparison with other study relating to random effects. It is for this reason that random effect associated with categorical data were used in the data fitting process, the model can be calibrated to fit the Chungnam region by obtaining measurements. Therefore, the results of this study could be useful method for developing biomass model using random effects by region.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.4
• /
• pp.576-584
• /
• 2018

Objective: This study aimed to develop a value-added product concerning technological and sensory characteristics changes of the use of mechanically deboned poultry meat (MDPM) as meat replacer in lamb and mutton emulsion-type sausages (mortadella). Methods: Sausages were produced with lamb and mutton and with different contents of MDPM. Six treatments, using lamb or mutton and 0%, 30%, and 60% of MDPM in relation to the meat batter, were produced and analyzed for pH, proximal composition, calcium and residual nitrite content, water activity, 2-thiobarbituric acid reactive substances (TBARS), instrumental color and texture profile. The sensory profile of the mortadella's was also evaluated by acceptance test and check-all-that-applies (CATA) analysis. Results: The MDPM addition increased (p<0.05) fat, residual nitrite and calcium content in the all sausage formulations, but mutton sausage had (p<0.05) higher fat and lower moisture content than lamb sausage. The pH, water activity, TBARS index and color was not affected by MDPM additions, while the mutton sausages were significantly redder (higher $a^*$, $C^*$, and lower $h^{\circ}$) and darker (lower $L^*$) than lamb sausages. Adding up to 60% of MDPM reduced (p<0.05) sausages hardness and chewiness. Overall, the meat replacement by MDPM increased the sausages acceptance, but the mutton sausage with 30% of MDPM replacer were the most preferred. Consumers related that pink color, glossy appearance, poultry meat-like taste, soft texture, juicy and greasy mouth feel to all sausages contain MDPM according to CATA analysis. Conclusion: Mutton from culled ewes can be utilized for mortadella production with 30% replacement of lean mutton and fat by MDPM.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.377-382
• /
• 2001

Mechanical behavior and electrical resistance change of CPDP (carbon particle dispersed plastic) composite consisting of epoxy resin and conductive carbon particle were investigated under monotonic loading and repeated loading-unloading. The electrical resistance almost linearly increased with increasing strain during loading and the residual electrical resistance was observed even after removing load. The value of the residual electrical resistance was dependent on the maximum strain under the applied stress. This result suggests that the estimation of maximum strain (i.e., damage) is possible by the measuring electrical resistance of composite. The behavior of electrical resistance change during and after loading was discussed on the basis of the results of microscopic deformation and fracture observation. Moreover, the relationship between the volume fraction of carbon particle and the electrical resistivity of CPDP was investigated in relation to the percolation theory. Simulation model of percolation structure was established by Monte Carlo method and the simulation result was compared to the experimental results. The electrical resistance change under applied loading was analyzed quantitatively using the percolation equation and a simple model for the critical volume fraction of carbon particle as a function of the mechanical stress. It was revealed that the prediction was in good agreement with the experimental result except in the region near the failure of material.

• Korean Journal of Medicinal Crop Science
• /
• v.21 no.2
• /
• pp.124-129
• /
• 2013

This study was conducted to investigate the residual contents of sulfur dioxide ($SO_2$) in commercial medicinal herbs in Korea in 2012. Among a total of 136 samples of 16 different kinds of herbs, 86 samples (15 Kinds) were domestic, and 50 samples (14 Kinds) were imported. Sulfur dioxide in the samples was measured by a modified Monier-Williams method. Of the 136 samples, 17 samples (12.5%, 6 Kinds) failed to meet the regulations for sulfur dioxide residues of KFDA in medicinal herbs. Among 17 unsuitable samples, 7 samples (8.1%, 3 Kinds) were domestic, and 10 samples (20.0%, 6 Kinds) were imported. The highest amount of sulfur dioxide residues was 3,167.94 mg/kg (Lycii Fructus) in the domestic samples. The detection frequency of sulfur dioxide by medicinal herb parts used, Rhizoma 25.7%, Flos 20.0%. Cortex 12.5%, Radix 15.3%, Fructus 7.6%, p-value 0.011. This results will be used as a basic data for the future legislation on the quality estimation and safety of medicinal herbs.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.16 no.3
• /
• pp.197-207
• /
• 2016

It is very important to maintain a constant chlorine concentration in the post chlorination process, which is the final step in the water treatment process (hereafter WTP) before servicing water to citizens. Even though a flow meter between the filtration basin and clear well must be installed for the post chlorination process, it is not easy to install owing to poor installation conditions. In such a case, a raw water flow meter has been used as an alternative and has led to dosage errors due to detention time. Therefore, the inlet flow to the clear well is estimated by a time series neural network for the plant without a measurement value, a new residual chlorine meter is installed in the inlet of the clear well to decrease the control period, and the proposed modeling and controller to analyze the chlorine concentration change in the well is a neuro fuzzy algorithm and cascade method. The proposed algorithm led to post chlorination and chlorination improvements of 1.75 times and 1.96 times respectively when it was applied to an operating WTP. As a result, a hygienically safer drinking water is supplied with preemptive response for the time delay and inherent characteristics of the disinfection process.