• Macromolecular Research
• /
• v.11 no.5
• /
• pp.297-302
• /
• 2003

The imidization and cure reaction of a thermosetting phenylethynyl-terminated amic acid (LaRC PETI-5) in film form have been monitored as a function of temperature by means of a steady-state fluorescence technique using a front-face illumination method. The variation of the fluorescence emission spectra of LaRC PETI-5 can be divided into four temperature regions; Region I: below 15$0^{\circ}C$, Region II: 150-25$0^{\circ}C$, Region III: 250-35$0^{\circ}C$, and Region IV: above 35$0^{\circ}C$. The fluorescence spectra in Region I are largely influenced by residual N-methyl-2pyrrolidinone in the polymer and also slightly by partial imidization of the polymer. There is a combined effect of imidization and solvent removal on the fluorescence behavior in Region II. The spectra in Regions III and IV are due significantly to the cure reaction of LaRC PETI-5 and to a post-cure effect of the polyimide, respectively. This spectroscopic evidence indicating the transformation of the amic acid imide oligomer into the corresponding polyimide via imidization and cure, agrees well with thermal analysis results obtained previously. The intermediate stage of cure in the range of 250-30$0^{\circ}C$ predominantly influences the change of the fluorescence intensity. The later stage above 30$0^{\circ}C$ significantly influences the position of the spectrum. This fluorescence study also supports the mechanism proposed in earlier work that the crosslinking reaction takes place at the reaction sites in the conjugated polyene and the phenylethynyl end group in the polyimide chain.

• Macromolecular Research
• /
• v.11 no.1
• /
• pp.9-13
• /
• 2003

Poly (vinylidene fluoride) (PVDF) samples were implanted by using high energy (MeV)F$^{2+}$ and Cl$^{2+}$ ions. We observed that AC dielectric constant of the ion-implanted PVDF samples decreased from 10.5 to 2.5 at 1 kHz as the ion dosage increased from 10$^{11}$ to 3 $\times$ 10$^{14}$ ions/$\textrm{cm}^2$. From differential scanning calorimetry experiments, we observed that PVDF samples become more disordered state through the ion implantation. The decrease of the number of bonding of C-H and C-F and the increase of unsaturated bonding were observed from X-ray photoelectron spectroscopy experiments. The emission of HF and H$_2$ molecules during the ion implantation was detected by residual gas analyzer spectrum. Based upon the results, we analyzed that the low AC dielectric constant of the MeV ion-implanted PVDF samples originated from the reduction of polarization due to the structural change of the CF$_2$ molecules in the MeV ion-implanted PVDF samples.les.

• Applied Chemistry for Engineering
• /
• v.22 no.5
• /
• pp.495-500
• /
• 2011

Separation of naphthalene from pyrolyzed fuel oil, by product of Naphta cracking process (NCC) process, has been accomplished by the solvent extraction, distillation and purification process. The residual pyrolyzed fuel oil (PFO), called precursor of carbon materials, has been calcined at $300{\sim}800^{\circ}C$ in nitrogen gas to raw pitch. After the treatment of PFO by hexane and methanol, either a flake phased carbon at $350^{\circ}C$ or a carbon sphere at above $400^{\circ}C$ forms. As the calcination temperature increases, the shape of raw pitch changes from the flake phase to the sphere one, and the size of them decreases to several ${\mu}m$. Based on the BET and XRD spectrum, the carbon sphere is classified to a mesophase amorphous carbon with a cubic phase.

• Journal of Life Science
• /
• v.9 no.2
• /
• pp.194-200
• /
• 1999

Grinding aid is a necessary unit operation when the raw materials are handled in solid form, and the purpose is to improve the bioavailability by reducing the particle size. For the particle design of pefloxacin, the dry planetary ball-mill was used. With the drying process, 330 g of zirconia ball with its size of 2 mm in diameter and 10 g of pefloxacin were transferred to the pot and mixed well. The mixture was ground at 112 rpm (60 Hz) for 15, 30, and 60 min, respectively. The most satisfactory grinding products were generated at 15 min of grinding time for their particle size. The volume mean diameter $\X_50$ of the grinding products was 2.97 $\mu$m. X-ray diffraction (XRD), differential scanning calorimeter (DSC), and infrared spectroscopy (IR) patterns were relatively unchanged before pulverizing pefloxacin and in the progress of grinding. Thus, these results suggest that this pulverizing method can be used for grinding products without evident effect on stability of the drug pefloxacin. Dissolution test was carried out to set up the optimal detective condition against residual antibacteria of fish by HPLC. The grinding pefloxacin for 15 min is most effective in dissolution test.

• Korean Journal of Soil Science and Fertilizer
• /
• v.25 no.4
• /
• pp.401-406
• /
• 1992

Antifungal substances against three plant pathogenic fungi, Phytophthora capsici, Phytophthora nicotianae var. parasitica and Rhizoctionaia solani were fractionated cultures of Streptomyces sp. A-2 strain isolated in Korean soils. Characterizations of active substances related with antagonistic effects were follows : 1. The excellent media which showed the transfer efficiency of antagonistic substances from Streptomyces sp. A-2 strain G.Y.B and B.H.I. among four that are glucose yeast broth (G.Y.B), $M\ddot{u}eller$, brain heart infusion(B.H.I.) and Czapek media. Active substances which were transfered into ethylacetate or left in residual aqueous phase did not lose antagonistic activity in spite of autoclavation. This indicated that bonds of these compounds were rigid enough to keep activity under such conditions. 2. Antagonistic substances were extracted according to adjustment of pH 3 or pH12 to 5 day-old B.H.I. broth cultures of Streptomyces sp. A-2 strain. Comparative analysis fluorescent bands on HPTLC to antagonsitic spectra against three phytopathogenic fungi indicated that major substances with antagonistic activity were extracted regardless of different pH adjustment to broth cultures. Since UV spectrum of these fractions scanned from 500nm to 200nm was similiar to that of polyene macrolide, major substances related with antagonistic activities were assumed to be polyene derivatives antibiotics.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.1
• /
• pp.20-26
• /
• 2001

Titanium boride ($\textrn{TiB}_{x}$) films were deposited on (100) silicon substrates at the substrate temperature of $500^{\circ}C$ by means of the co-evaporation of titanium and boron evaporants during deposition. The co-evaporation method makes it possible to deposit the non-stoichiometric films with different boron-to-titanium ratio($0{\le}B/Ti \le 2.5$). The resistivity increases linearly as the boron-to-titanium ratio in the as-deposited films is increased. The surface roughness of $\textrn{TiB}_{x}$ films is changed as a function of the boron-to-titanium ratio. The XRD spectrum for pure titanium film shows a highly (002) preferred orientation. For B/Ti=0.59 ratio only a single TiB phase that shows a (111) preferred orientation is observed. However, the $\textrn{TiB}_{x}$ phase with the hexagonal structure of the $AlB_2$(C32) type appears as the boron concentration increase, and only a single $\textrn{TiB}_{x}$ phase is observed for $B/Ti \ge 2.0$ ratio. The $\textrn{TiB}_{x}$/Si samples reveal a tensile stress (3~$20{\times}^9$dyn/$\textrm{cm}^2$) in the overall composition of the films, although the magnitude of the residual stresses is depended on the nominal B/Ti ratio.

• Journal of The Korean Society of Inherited Metabolic disease
• /
• v.13 no.1
• /
• pp.37-42
• /
• 2013

Gaucher disease is a lysosomal storage disease caused by deficiency of glucocerebrosidase (GBA). This condition is characterized by accumulation of glucocerebrosidase in liver, spleen, lung, skeletal system, and central nervous system. Gaucher disease is the prototype of disease in which efficacy of enzyme replacement therapy has been established. However, because recombinant enzyme is not able to enter the central nervous system, its efficacy is limited to the non-neurological manifestations of Gaucher disease. Importantly, approximately a half of Korean patients with Gaucher disease suffer from neurological manifestations. In addition, Korean Gaucher disease patients exhibit distinct mutation spectrum from those in other populations. Common mutations in Korean patients with Gaucher disease are also associated with neurological phenotype. Therefore, therapeutic strategies tailored to Korean patients were necessary. Interestingly, a chemical chaperone, ambroxol, has been known to increase residual enzymatic activities of the select mutant GBAs encoded by mutations prevalent in Korean patients. One promising aspect of this drug is that it can cross blood-brain barrier, and enhance the enzyme activity in the brain. In vitro study suggested this chemical chaperone as one of new therapeutic agents in Gaucher disease, and a well-designed human trial is required to confirm its efficacy.

• Tuberculosis and Respiratory Diseases
• /
• v.63 no.6
• /
• pp.515-520
• /
• 2007

Mycoplasma pneumoniae (M. pneumoniae) is the leading cause of pneumonia in older children and young adults. Normally, it does not progress to a condition requiring hospitalization but improves spontaneously or has a mild clinical course. We report two cases of M. pneumoniae pneumonia with different clinical manifestations from the normal course. The patients were young healthy individuals. The diagnoses were made by serology. However, it could not be determined beforehand that they had M. pneumoniae pneumonia. Based on the empirical treatment strategy of severe community acquired pneumonia, the patients were treated with broad-spectrum antibiotics including cephalosporin, quinolone and macrolide. After administering the antibiotics, they showed a gradually favorable clinical course and recovered without residual complications. A M. pneumoniae infection should be considered as a cause of severe community acquired pneumonia, and empirical treatment targeting this organism might be helpful in treating patients with the severe manifestation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.3
• /
• pp.92-95
• /
• 2019

In this paper, a novel laser-based non-contact and non-destructive stress measurement technique is newly proposed for measuring stress in steel structural members. As the demand of stress monitoring in structural members is increased, various non-destructive techniques are being applied to the field of structural health monitoring. Spectroscopic techniques are non-contact technique and widely used for chemical identification of target materials. Especially, piezospectroscopic technique is a residual stress measurement technique in thermal barrier coatings. Although the piezospectroscopic technique has high possibility of measuring structural stress in steel members, the technique has been rarely applied to this field. In this paper, piezospectroscopy-based stress measurement technique is, therefore, proposed for measuring stress in steel structural member. To do that, alumina particles have been coated onto a specimen of a structural steel rod using a thermal spray coating technique. And then, an uniaxial compression test has been conducted to the specimen to collect each fluorescence spectrum under different loading conditions. Finally, the linear relation of spectral shift and applied compressive stress of the specimen has been experimentally established.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.1
• /
• pp.19-25
• /
• 2015

Nowadays, CAD/CAM is broadly used in dentistry for inlays, crowns, implant abutments and its spectrum is expanding to complete dentures. Utilizing CAD/CAM to fabricate complete dentures is expected to decrease chair time and the number of visits, thus decreasing total fabrication time, expenses and errors caused during fabrication processes. One of the systems using CAD/CAM, DENTCA$^{TM}$ CAD/CAM denture (DENTCA Inc. Los Angeles, USA) scans edentulous impressions, designs dentures digitally, fabricates try-in dentures by 3D printing and converts them into final dentures. Patients can wear final dentures after only 2 - 3 visits with satisfying adaptation. This case report introduces a 71-year-old male patient who visited to consult remaking of existing old dentures. Residual teeth with bad prognosis and root remnants were extracted and the patient used reformed existing mandibular denture for 2 months. And then DENTCA system started. One-step border molding was done using conventional tray of adequate size provided by DENTCA system and wash impression was taken. Gothic arch tracing was completed based on the vertical dimension of existing dentures. Both maxillary and mandibular trays were placed to the resultant centric relation and bite registration was taken. Then DENTCA scanned the bite registration, arranged the teeth, completed the festooning and fabricated the try-in dentures by 3D printing. The try-in dentures were positioned, occlusal plane and occlusal relations were evaluated. The try-in dentures were converted to final dentures. To create bilateral balanced occlusion, occlusal adjustment was done after clinical remounting using facebow transfer. The result was satisfactory and it was confirmed by patient and operator.