• Archives of design research
• /
• v.19 no.5 s.67
• /
• pp.129-138
• /
• 2006

It is expected that the typical lifestyle of the future will be transformed into an opulent and comfortable existence as the quality of life improves due to the increase in household income and reduction in working hours. In the meantime, as the standard of living becomes increasingly more comfortable and plentiful, the toll on physical health becomes magnified as a result of obesity and insufficient exercise caused by super nutrition and change in labor conditions (from physical labor to mental labor). This has instigated a deep awareness in fitness on the part of many people, forcing them to recognize the significance of daily exercise and physical activity. The high annual growth rate in the fitness and athletic apparatus market, which is more than 20%, is attributed to this phenomenon. The Elliptical Cross Trainer(ECT), which has drawn wide attention recently, is a non-impact athletic apparatus that not only promotes exercise of the upper body parts in such sports as skiing but also the exercise of lower parts of the body on a treadmill. It is a type of cross training athletic gear that has been developed for aerobic exercise throughout the entire body. It has already formed a market as big as that of the treadmill in Europe, America, etc. Recently, its demand is growing sharply in the Korean markets as well as those in Northeast Asian countries, Despite such demand increase and expansion, since most of the expensive ECTs are exclusively supplied by suppliers in only a few advanced countries, localization of the ECT is urgently required in order to enhance competitiveness of Korean manufacturers and to expand the market. This paper introduces the process and results of a design-engineering cooperative study that was peformed for the development of the ECT.

• Archives of design research
• /
• v.18 no.1 s.59
• /
• pp.167-174
• /
• 2005

This study is to objectively support the emotional and intuitional decision making of the designer by means of developing the supporting models and tools of color coordination. Based on the color grouping system and representative vocabularies suggested in the precedent 'Study on the Grouping System of Fabric Color,' this study suggested the manufacture of the supporting model of color coordination that could be used practically through the design of coloring group. The results of this study can be summarized as below. Firstly, 687 colors in total have been collected from the four world famous collections, the street fashion of 2002 F/W 2003 S/S Season and the representative brands in each group for five years from 1999 to 2003 in order to single out the basic colors for the purpose of composing the color groups. Secondly, 687 collected colors have been grouped into 144 colors in total through the three-step process for the extraction of coloring groups. Thirdly, the final extracted colors have been divided into , , , group by the grouping system specified in the precedent study and the said four large groups have been again subdivided into 12 small groups. Fourthly, the suggested colors in each group have established a color coordination system by introducing the concept of the crossover coordination that could be matched with other groups as well as the coordination within the group. Fifthly, we have dyed 144 colors in total that have consisted of the coloring system of four representative groups (twelve subgroups) in each methodical tone as in the above in cotton yarn, one of the representative materials in fabric fashion design industry. Besides, we have specified the symbol of the Pantone Color Book and CMYK values in each color that has consisted of the system considering the industrial characteristics of fashion as a global business and the compatibility with the related design industry. Sixthly, we have packed the completed yam made of fabrics in the designed container for the easy use of cross-coordination and have completed a color coordination system that could be easily utilized for the fashion-related working-level staffs.

• The Korean Journal of Pharmacology
• /
• v.32 no.3
• /
• pp.301-309
• /
• 1996

Since it has been reported that the depolarization-induced NE release is inhibited by activation of presynaptic $A_1-adenosine$ heteroreceptor in hippocampus, a large body of experimental data on the post-receptor mechanism of this process has been accumulated. But, the post-receptor mechanism of presynaptic $A_1-adenosine$ receptor on the NE release has not been clearly elucidated yet. Therefore, it was attempted to clarify the participation of $K^+-channel$ in the post-receptor mechanisms of the $A_1-adenosine$ receptor-mediated control of NE release in this study. Slices from rat hippocampus were equilibrated with $^3H-norepinephrine$ and the release of the labelled products was evoked by electrical stimulation (3 Hz, 5 $VCm^{-1}$, 2 ms, rectangular pulses), and the influence of various agents on the evoked tritium-outflow was investigated. Adenosine, in concentrations ranging from $1{\sim}30\;{\mu}M$, decreased the NE release in a dose-dependent manner, without affecting the basal rate of release. 4AP $(1{\sim}30{\mu}M)$, a specific A-type $K^+-channel$ blocker, increased the evoked NE release in a dose-related fashion, and the basal rate of release is increased by 10 and $30{\mu}M$. TEA $(1{\sim}10{\mu}\;M)$, a nonspecific $K^+-channel$ blocker, increased the evoked NE release in a dose-dependent manner without affecting basal release. The adenosine effects were significantly inhibites by 3 ${\mu}M$ 4AP and 10 mM TEA treatment. 4AP $(30{\mu}M)-$ and TEA (10 mM)-induced increments of evoked NE release were completely abolished in $Ca^{++} free, but these were recoverd in low $Ca^{++} medium. And the effects of $K^+-channel$ blockers in low $Ca^{++} medium were inhibites and abolishes by $Mg^{++} (4 mM) adding and TTX $(0.3{\mu}M)$ adding medium, respectively. These results suggest that the decrement of the evoked NE-release by $A_1-adenosine$ receptor is mediated by 4AP and TEA sensitive $K^+-channel$.

• Science of Emotion and Sensibility
• /
• v.21 no.2
• /
• pp.101-112
• /
• 2018

This study was carried out to enhance the competitiveness of blackbox design for domestic and international companies, based on the explosive growth of the blackbox market due to development of blackbox design for vehicle accident prevention and post-treatment. In the past, the blackbox market has produced products indiscriminately to meet the ever-increasing demand of consumers. Therefore, we thought a new design method was necessary to effectively investigate the needs of rapidly changing consumers. In this study, we aimed to identify the best-selling blackbox to understand the design flow, and the optimum area for a blackbox, considering the uniqueness of associated vehicle. Based on discussion with blackbox design experts, we studied the direction of design and the problems with blackbox use, which were reflected in blackbox development. Through this research, two types of design - leading blackbox (A type) and mass production blackbox (B type) - were proposed for compatibility of the blackbox with the car. The leading type of blackbox was positioned so that it was wrapped with the room mirror hinge before the screw was fastened, in order to achieve an integrated design. Therefore, we designed an integrated form and resolved the placement problem of an adhesive blackbox. To blend, the mass production blackbox implemented material and surface processing in the same way with the car, and adopted the slide structure to automatically turn off the main body power when removing the SDcard, reflecting consumer needs. This study considers evolving consumer needs through a case study and collective intelligence and deals with implementation of the whole design process during mass production. In this study, we aimed to strengthen the competitiveness of the blackbox design based on design method and its realization.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.578-589
• /
• 2018

Building Integrated Photovoltaic (BIPV) system is a typical integrated system that simultaneously performs both building function and solar power generation function. To maximize its potential advantage, however, the solar photovoltaic power generation function must be integrated from the early conceptual design stage, and maximum power generation must be designed. To cope with such requirements, preliminary research on BIPV design process based on architectural design model and computer simulation results for improving solar power generation performance have been published. However, the requirements of the BIPV system have not been clearly identified and systematically reflected in the subsequent design. Moreover, no model has verified the power generation design. To solve these problems, we systematically model the requirements of BIPV system and study power generation design based on the system requirements model. Through the study, we consistently use the standard system modeling language, SysML. Specifically, stakeholder requirements were first identified from stakeholders and related BIPV standards. Then, based on the domain model, the design requirements of the BIPV system were derived at the system level, and the functional and physical architectures of the target system were created based on the system requirements. Finally, the power generation performance of the BIPV system was evaluated through a simulated SysML model (Parametric diagram). If the SysML system model developed herein can be reinforced by reflecting the conditions resulting from building design, it will open an opportunity to study and optimize the power generation in the BIPV system in an integrated fashion.

• The Journal of the Korea Contents Association
• /
• v.12 no.3
• /
• pp.244-250
• /
• 2012

The results of analyzing the difference between performances of individual dosimeters on this research subjecting the PLD and TLD, which are the official personal dosimeters, through dosimetry are as follows. After scanning the integral dose using an automatic scanner, the values of two devices that went through dose adjustment process had a statistical difference in TLD and PLD measurements under each filming conditions which were 70kVp, 200mA, 0.012sec and 42kVp, 100mA, and 0.012sec (p<0.001 and p<0.001 respectively). As for the difference of measurement value between DAP and the two particles under 70kVp, 200mA, 0.012sec filming condition, TLD had a value lower than DAP average value by $44.2mGy{\cdot}cm^2$ and PLD had a value of $246.8mGy{\cdot}cm^2$ which was lower than DAP average value by $15.5mGy{\cdot}cm^2$, while under 42kVp, 100mA, 0.012sec filming condition, TLD had a value lower than DAP average value by $17.9mGy{\cdot}cm^2$ and PLD had a value of $82.6mGy{\cdot}cm^2$ which was lower than DAP average value by 7.6$mGy{\cdot}cm^2$. Also, compared to PLD, each of 10 devices measured dose value in TLD had a larger deviation between the particles, and for a reproducibility test which repeatedly measured one particle, PLD had ${\pm}1%$ which was lower than TLD's ${\pm}2%$. As such, PLD had a superior performance result in dose measurement capacities aspect compared to TLD, and therefore we could verify that PLD is more appropriate and advantageous in managing radiation-related task performing worker's personal radiation exposure management in the diagnostic radiation field.

• Journal of Korean Ophthalmic Optics Society
• /
• v.21 no.1
• /
• pp.11-21
• /
• 2016

Purpose: The aim of this study was to analyze the difference in tear film stability according to the wearing time when wearing clear and circle soft contact lens(circle lens) made of same material. Methods: The clear and circle contact lenses of hilafilcon B and nelfilcon A materials were respectively applied on the subjects classified as normal and dry eyes depending on their tear volume, and their tear film stability was investigated by measuring the non-invasive tear film break-up times, lens centration and the first appearing area of tear breakup after 30 mins and 6 hrs of lens wearing. Results: Non-invasive tear film breakup time significantly reduced with increase of the wearing time for normal and dry eyes when wearing clear and circle contact lenses. The starting ratio of tear film break-up was higher at the peripheral area of clear and circle lenses in all two different materials, and higher at the peripheral area of dry eyes than normal eyes. Starting ratio of tear film break-up was higher at the peripheral area of nelfilcon A lenses compared with hilafilcon B lenses, however, its change with the increase of wearing time showed a different aspect. The number of tear film break-up per unit area when wearing circle lenses of nelfilcon A increased at the central area with the wearing time while its number was higher at the peripheral area when wearing circle lenses of hilafilcon B. The centration of clear lenses made of two materials was closer to pupil compared to circle lenses with the increase of wearing time, however, a larger decentration was shown in dry eyes compared with normal eyes. Conclusions: The research revealed that an effect on tear film stability may be changed by clear lenses as well as circle lenses with coloring process according to the increase of wearing time, and the factors affecting on tear film stability may also vary depending on lens materials. Thus, the appropriate lenses should be selected by the consideration of lens material as well as coloring method/dyes according to the wearers' habit such as daily wearing time and wearing period when trying to wear clear and circle lenses.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.12
• /
• pp.1274-1279
• /
• 2006

The formation characteristics of $BDOC_{rapid}$ and $BDOC_{slow}$ with different ozone dosages for 3 different kinds of waters from Maeri raw water in the down stream of Nakdong river, Hoidong reservoir water in Busan City and treated Maeri raw water(sand filtered) has been investigated in this study. The ozone dosages for producing maximum $BDOC_{total}$ in the Maeri raw water, Hoidong reservoir water and sand filtered water of Maeri were 0.9, 1.1 and 1.4 $mgO_3$/mgDOC respectively. It could be concluded that the ozone dosages for formations of maximum $BDOC_{total}$ were determined by characteristics of water. The ozone dosages for producing maximum $BDOC_{rapid}$ in the Maeri raw water, Hoidong reservoir water and sand filtered water of Maeri were 0.9, 0.9 and 1.0 $mgO_3$/mgDOC respectively that were same or lower than the used ozone dosages for producing maximum $BDOC_{total}$. $BDOC_{slow}$ was being formated and increased continuously with the higher ozone dosages which were the used ozone dosages for maximum formation of $BDOC_{total}$ and $BDOC_{rapid}$. For the best results of a pre-treatment of biofiltration, the optimum ozone dosage ranges in formation of $BDOC_{rapid}/BDOC_{total}$ were $0.6{\sim}1.0\;mgO_3$/mgDOC that were lower than the ozone dosage ranges of $0.9{\sim}1.4\;mgO_3$/mgDOC for the maximum formation $BDOC_{total}$. The reported results indicated that the best and effective ways from economic and technical points of view to determine the optimum ozone dosages of the pretreatment of biofilteration process were investigating and classifying BDOC.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.11
• /
• pp.1116-1122
• /
• 2008

The existing technology which is for recycling aggregate using dried swage sludge have been limited for practical application, because the properties of aggregate are not regular and don't meet the recycling aggregate standard. In this research, an innovative slag-producing technology is developed by addition of oyster shell, waste cast-sand and iron-rust as inorganic waste additives. The mixed slag with the additives was evaluated at the various ratio of CaO/SiO$_2$, SiO$_2$/Al$_2$O$_3$ and Fe$_2$O$_3$/SiO$_2$. When the waste sludge was melted at 1,400$^{\circ}C$ during 20 minutes, the optimal ratio of CaO/SiO$_2$ for the slag added the oyster shell, SiO$_2$/Al$_2$O$_3$ for added the waste cast-sand and Fe$_2$O$_3$/SiO$_2$ for added the iron-rust were 1.00, 3.00 and 0.60, respectively. At the optimal condition, the bulk density of the slag was 2.24 g/cm$^3$, 2.45 g/cm$^3$ and 2.73 g/cm$^3$, And the 24 h water adsorption was 4.72%, 1.44% and 0.37%, respectively. Therefore it is proved that adding the waste additives to the process of the slag production contributed for elevation of recycling aggregate properties. And also it is expected that production cost can be reduced by decreased melting temperature.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.1
• /
• pp.235-246
• /
• 2018

Paeony has pharmacological activities such as anti-inflammatory, anti-allergic, anti-bacterial, central inhibitory, gastric secretion inhibition, and antispasmodic activities. In addition, its antioxidant activity and whitening effect being reported, thus it is being explored as raw materials for cosmetics. We compared the changes in the contents of paeoniflorin and paeonol in Peony extracts, depending on the changes of extracting solvents, temperature and time. The HPLC method was set up for simultaneous analysis, the system suitabilities were confirmed by using the calibration curves and the QC samples for each assay batch. Paeonol was detected only in roots, and paeoniflorin was higher in leaf and flower than root. Higher concentrations of both ingredients were extracted when the root was used after grinding to a suitable size, and when 30% 1,3-butylene glycol was used as the extraction solvent. Also the concentrations tended to increase at higher temperature and longer time, but the increase was gradual at over $75^{\circ}C$ and 4 hours. The ratio of root, leaf and flower was determined to be 2+2+1g/0.5kg of batch, reaching the contents criteria of paeoniflorin and paeonol. Finally, we selected as the best extraction condition when the raw materials are mixed with 2+2+1g/0.5kg and extracted with 30% 1,3-butylene glycol as an extraction solvent at $75^{\circ}C$ for 4 hours, considering both the concentrations of two components and the cost of raw materials and manufacturing process, The extraction units were scaled up to 10 kg under this condition.