알루미늄 폐드로스는 알루미늄 용해업체에서 발생되는 주요 폐기물 중 하나인데, 폐드로스에는 상당량의 금속 알루미늄이 잔류한다. 본 연구에서는 알루미늄 폐드로스 내에 잔류하는 금속 알루미늄을 회수하고자 폐드로스를 수산화나트륨 용액으로 침출하여 폐드로스 중의 잔류 알루미늄을 용액 상으로 침출, 분리시킨 다음. 침출용액 중에서 알루미늄 성분을 수산화알루미늄으로 제조하는 연구를 수행하였으며, 연구결과의 상용화를 위하여 시범생산라인을 건설하여 시운전하였다. 시범생산라인은 년간 1,000톤의 폐드로스를 처리하여 500톤의 수산화알루미늄을 생산할 수 있는 규모이다. 생산라인의 시운전 결과 연구 개발한 기술의 상용화 가능성을 확인할 수 있었으며, 시험생산한 수산화알루미늄은 수처리 응집제용으로 사용 가능하다고 판단된다.
알루미늄드로스의 재활용은 알루미늄 재생지금 제조시에 요구되는 중요한 사항 중의 하나이다. 본 연구에서는 국내 재생 알루미늄업체에서 발생된 알루미늄드로스를 처리하여 알루미나질 내화물 원료로 재활용하고자 하였다. 드로스 시료를 크기에 따라 선별하고, 1 mm보다 작은 크기의 드로스를 수산화나트륨 용액으로 침출하여 드로스 중의 잔류 알루미늄을 용액 중으로 분리 추출하고, 침출용액에서 석출반응에 의하여 수산화알루미늄을 회수하였다. 드로스 중의 금속알루미늄을 회수한 후 발생된 침출잔사는 수세, 건조, 배소와 같은 일련의 처리를 하여 드로스 중의 잔류 금속성분을 산화물 형태로 변환시켰다. 배소 처리한 드로스 잔사를 골재 및 점결제와 배합하여 알루미나질 캐스타블내화물을 만들고, 굽힘강도와 압축강도를 시험한 결과 KS 기준치인 굽힘강도 $25\;kg/\textrm{m}^2$ 이상, 압축강도 $80\;kg/\textrm{cm}^2$ 이상을 만족하였다. 본 연구결과를 알루미늄드로스를 효율적으로 재활용할 수 있는 한가지 방안으로 제안하고자 한다.
알루미늄 폐드로스는 알루미늄 용해업체에서 발생되는 주요 폐기물 중 하나인데, 주요 성분은 알루미나이며 상당량의 금속 알루미늄이 잔류한다. 알루미늄 폐드로스 내에 잔류하는 금속 알루미늄을 수산화나트륨 용액으로 침출, 분리시켜서 수산화알루미늄으로 제조하는 과정에서 침출잔사가 발생되는데, 침출 후 여과잔사의 주요 성분은 알루미나이다. 본 연구에서는 이 침출잔사를 세척, 건조, 배소하여 알루미나질 캐스타블 내화물과 같은 세라믹 원료로 재활용하는 연구를 수행하였으며, 상용화를 위한 파일롯트 플랜트시험을 수행하였다. 실증 생산라인은 년 간 1,000톤의 폐드로스를 처리하여 약 700톤의 세라믹 원료를 생산할 수 있는 규모이다. 생산라인의 시운전 결과, 개발 기술의 상용화 적용 가능성을 확인하였으며 상용화를 위해서 건조기의 개선과 Na, Fe등 불순 성분들이 시료에 유입되는 것을 줄여야 하는 문제점들을 파악할 수 있었다.
The effect of asymmetric rolling on the recrystallization texture of an AA 3003 Aluminum alloy was investigated by X-ray diffraction. It was found that the texture of asymmetrically rolled sheets prior to subsequent heat treatment promoted the formation of the <111>//ND textures, and remained after heat treatment at $275^{\circ}C$ during 20 min in salt bath condition.
In order to investigate the possibility of Ni-Al based intermetallics coating onto aluminum substrate, the coating process for induction heating has been evaluated by microscopically analyzing the intermetallic layers coated at temperatures lower than the melting temperature of aluminum. The coating layers were divided into two parts with different microstructure along the depth. Hard $NiAl_3$ layer was found at lower parts of the coatings near the interface with aluminum substrate. This layer was formed by the diffusion of aluminum atoms from the substrate into the coating layer across the interface during the induction heating. Meanwhile, at the upper parts of the coating near the surface, a large amount of un-reacted Ni was still remained and surrounded by several Ni-Al based intermetallic compounds, such as $Ni_3Al$, NiAl and $Ni_2Al_3$ formed by the lattice diffusion.
알루미늄 지금 및 스크랩 용해시 발생되는 알루미늄 폐드로스를 사용하여 황산알루미늄(Alum)과 폴리염화알루미늄(pooly Aluminium Chloride: PAC)을 제조하였다. 알루미늄 폐드로스를 황산과 반응시켜 폐드로스 중에 잔류하는 금속알루미늄을 용액 중으로 침출시켜 황산알루미늄 용액으로 제조하였으며, 알루미늄 폐드로스를 염산과 반응시켜 PAC 용액으로 제조하여 수처리응집제로 재활용하고자 하였다. 이와 같이 알루미늄 폐드로스를 재활용함으로써 수산화알루미늄을 원료로 사용하여 황산알루미늄과 PAC를 제조하는 종래의 방법에 비해 제품의 원료비를 줄일 수 있고, 매립 등으로 폐기시켜야 할 폐드로스의 양을 줄이는 효과가 있었다.
국내 알루미늄 재생업체에서 알루미늄 용해시 발생되는 알루미늄 폐드로스를 사용하여 수처리응집제로 사용되는 황산알루미늄을 제조하였다. 알루미늄 폐드로스를 황산과 반응시켜 폐드로스 중에 잔류하는 금속알루미늄을 황산알루미늄용액으로 제조함으로써 수산화알루미늄을 원료로 사용하여 황산알루미늄을 제조하는 종래의 방법에 비해 제품의 원료비를 줄일 수 있고, 알루미늄 폐드로스를 재활용함으로써 매립 등으로 폐기시켜야 할 폐드로스의 양을 줄이는 효과가 있었다.
There has been increasing interest in the fabrication of nano-sized structures because of their various advantages and applications. Anodic Aluminum Oxide (AAO) is one of the most successful methods to obtain highly ordered nano pores and channels. Also It can be obtained diverse pore diameter, density and depth through the control of anodization condition. The three types of substrates were used for anodization; sheets of Aluminum on Si wafer and Aluminum on Mo-coated Si wafer. In Aluminum sheet, a highly ordered array of nanoholes was formed by the two step anodization in 0.3M oxalic acid solutions at 10$^{\circ}C$ After the anodization, the remained aluminum was removed in a saturated HgCl$_2$ solution. Subsequently, the barrier layer at the pore bottom was opened by chemical etching in phosphoric acid. Finally, we can obtain the through-channel membrane. In these processes, the effect of various parameters such as anodizing voltage, anodizing time, pore widening time and pre-heat treatment are characterized by FE-SEM (HITACH-4700). The pore size. density and growth rate of membrane are depended on the anodizing voltage and temperature respectively. The pore size is proportional to applied voltage and pore widening time The pore density can be controlled by anodizing temperature and voltage.
국내 알루미늄 재생업체에서 알루미늄 용해시 발생되는 알루미늄 폐드로스를 사용하여 수처리응집제로 사용되는 폴리염화알루미늄(PAC: Poly Aluminium Chloride)를 제조하였다. 알루미늄 폐드로스를 염산과 반응시켜 폐드로스 중에 잔류하는 금속알루미늄을 PAC용액으로 제조함으로써 수산화알루미늄과 염산을 원료로 사용하여 PAC를 제조하는 종래의 방법에 비해 제품의 원료비를 줄일 수 있고, 알루미늄 폐드로스를 재활용함으로써 매립 등으로 폐기시켜야 할 폐드로스의 양을 줄이는 효과가 있다.
한국펄프종이공학회 1999년도 Pre-symposium of the 10th ISWPC Recent Advances in Paper Science and Technology
/
pp.239-244
/
1999
aluminum sulfate (alum) as a representative retention aid in papermaking processes was added to pulp suspensions, and the aluminum components adsorbed on the pulp were investigated quantitatively by two types of X-ray elementary analyses with regard to simultaneous changes of their surface charges. X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence analysis (XFA) were applied to determine the aluminum components retained in pulp pads up to ca. 10 nm and 100${\mu}$m depth, respectively. In other words, XPS was utilized to analyze the outermost surface layers of the samples, and XFA was available for measurement of their extensive regions. A particle charge detector (PCD) was used to monitor streaming potentials at various pHs of the pulp mixtures under moderate sharing conditions. At pH 4.5 of pulp suspensions containing alum, surface charges of pulp fibers varied from negative to slight negative (approximately neutral) according to adsorption of aluminum components onto the pulp fibers. Subsequently, when a dilute NaOH solution in limited amounts was added to pulp mixtures, both streaming potentials and surface aluminum content of the pulp fibers increased distinctly although little total aluminum retention increased. Further addition of alkali solutions brought drastic decreases of the surface charges and surface aluminum content, while total aluminum content, on the contrary, increased gradually under neutral conditions. These results indicate that residual aluminum ions remained in pulp suspensions are predominantly adsorbed on surfaces of pulp fibers by adequate alkali additions and they must sufficiently cationize the fiber surfaces with increases of somewhat cationic aluminum complexes formed on the surfaces. On the other hand, aluminum components formed in higher pH ranges have nearly no contribution to improvement of charge properties of the pulp fiber surfaces, even though aluminum retention in pulp pads increases. XPS and XFA analyses combined with streaming potential measurement using a PCD suggest close relationships between aluminum content on the pulp fiber surfaces and their charge properties.
이메일무단수집거부
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.