• Journal of environmental and Sanitary engineering
• /
• v.21 no.4 s.62
• /
• pp.29-38
• /
• 2006

This study included the development of analytical method for determining perchlorate in water sample. The analytical condition was referred in EPA 314.0 method which use ion chromatography and the concentrator column was replaced by the guard column. Concentrating 10mL raw or treated water sample on to AGl6 guard column made it possible to get the LOD(Limit of Detection) of $0.73\;{\mu}g/L$. The total run time was 11 minutes and during run time next sample could be concentrated on AGl6 guard column. Compared to the Concentration method which needed manual operation, the Direct Injection method could screen the many water samples. The LOD of the Direct Injection method was higher and the sensitivity was lower than that of the Concentration method. The RSDs(Relative Standard Deviations) were lower than 2.5 % for peak height and 0.7 % for retention time in pre-concentration methods. This method Showed good reproducibility and reliability and it was thought the deviations of recovery value could be reduced by considering column capacity and making water sample homogeneous. Matrix Elimination could be done using the pre-concentration method if perchlorate were in complex matrix of sample.

• Hwankyungkyoyuk
• /
• v.14 no.2
• /
• pp.106-115
• /
• 2001

So far, most of studies on environmentally responsible behaviors were based on the Hines et. al.(1987)'s behavior model which emphasized mainly personal causes of behaviors. This study was planned to investigate whether self-efficacy and conformity toward social norm could be good predictors for environmentally responsible behaviors or not. In the preliminary study, Several scales on environmental problems were made up for measuring the levels of knowledge, attitude, and behavior from usually used items of previous studies. And, some relevant items to self-efficacy scale and conformity toward social norm scale were selected through factor analysis and reliability analysis recursively. In the main study, Knowledge, attitude, self-efficacy, conformity toward social norm, and behavior of high school students were measured in urban and rural areas. Results showed that students in urban areas took environmentally responsible behavior more often than ones in rural areas, and there were no differences in attitude and sensitivity but significant differences in self-efficacy and confirmity toward social norm between them. According to regression analysis, self-efficacy was the best predictor for environmentally responsible behaviors, and confirmity toward social norm and knowledge were also good predictors. In conclusion, self-efficacy and confirmity toward social norm are better predictors for environmentally responsible behaviors than attitude.

• The Journal of Korean Society for School & Community Health Education
• /
• v.7
• /
• pp.87-99
• /
• 2006

Objectives: This study is to draw the design of the program which is improve school health promotion participation by applying the Social Ecological Model based on the literature review on the health promotion. Methods: Literature review was carried out based on 5 factors of social ecological model using computer search engines of Google, ProQuest, and Riss4U. Results; Social Ecological Model is consist of individual, interpersonal, institutional/organizational, community, and policy. Individual sphere is drawn from Health Belief Model, interpersonal sphere is Social Support Theory, institutional/ organizational sphere is institutional resources theory, community sphere is community model, and policy sphere is Social Marketing Theory. The literature review show that the important variables affecting health promotion exist in each sphere. Individual sphere has social economic status, age, sex, sensitivity and specificity of illness, self-efficacy. Interpersonal sphere has support and use of family, friend and neighbor. Institutional/Organizational sphere has environment service reliability and utility. Conclusions: Community sphere has distance, neighborhood safety, interrelationship among institutions. Policy sphere has cost, legislation advertisement, lobby and concern and leadership of Institution.

• Tribology and Lubricants
• /
• v.29 no.6
• /
• pp.372-377
• /
• 2013

This study investigated the interface temperatures for the sliding friction of three types of pins fabricated with thermocouple wires by the suction casting method. Optical microscopy was used to examine the surrounding material state at the bonding interface with the thermocouple wires. Friction tests were performed under dry sliding conditions against stainless steel 304 at nominal stresses of 1.42-4.25 MPa and sliding speeds of 0.5-1.25 m/s. Tribological data were collected using a custom-made pin-on-disk apparatus that measured the interface temperature and corresponding friction coefficient. Static tests were performed to demonstrate the functionality and reliability of the thermocouple wires-combined temperature sensor (TCTS). Each TCTS showed good linearity and sensitivity and very similar response times for the thermocouple and critical temperature during sliding friction.

• Journal of the Ergonomics Society of Korea
• /
• v.22 no.3
• /
• pp.75-91
• /
• 2003

Evaluation of repetitiveness for hand-intensive tasks is essential to determine the level of risk for upper-extremity musculoskeletal disorders at the workplace. Many measures and methods have been introduced for repetitiveness assessment: however, our understanding of the differences among these measures and methods is lacking. The present study compared the repetitiveness measures and measurement/analysis methods to help practitioners apply the proper repetitiveness assessment methodology in the workplace. By reviewing 51 studies of repetitiveness assessment, measures and corresponding measurement/analysis methods were surveyed. Of the repetitiveness measures, two types of dimensions (frequency and time) and corresponding types of analysis scopes were identified. According to the dimensional and analysis-scope types. the repetitiveness measures were categorized and then the surveyed studies were counted for each measure. It is identified that frequency measures have used 2.7 times higher than time measures and the frequency of wrist motions has been most frequently used in repetitiveness assessment. Furthermore, the measurement methods were categorized into objective and subjective methods, and the analysis methods into statistical and spectral methods. Lastly, eight factors (accuracy, reliability. sensitivity. efficiency. ease of use. applicability. interference. and robustness) were listed to be considered in selecting the appropriate assessment methodology.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.225-228
• /
• 2008

In case of nonlinear analysis for reinforced concrete structure, the characteristics of the failure, which are depend on loading conditions, such as tension splitting, compression crushing and shear distortion should be considered. On the analytical evaluation for the failure behavior of these, the finite element techniques is the most widely used. After the maximum load, however, an analytical results by finite element technique are depending on the size of the element. In this study, integral nonlocal model which is one of those study for overcoming the element sensitivity and dependancy, used for the failure analysis of box culvert specimen. Comparing on the experimental and analytical results, validity and reliability of integral nonlocal model are investigate.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.4
• /
• pp.249-255
• /
• 2012

The planar-type amperometric creatinine biosensor employing an additional enzyme layer containing creatine kinase and adenosine triphosphate was developed to eliminate severe interference from creatine. In the additional enzyme layer, an interfering substance, creatine is converted to noninterfering product, phosphocreatine. Furthermore, the carbon electrode electroplated with Pt black(Pt-B) was employed to fabricate creatinine biosensors with improved sensor performance(e.g., sensitivity, reliability, and reproducibility). The creatinine levels in an unknown sample were determined within less than 5% errors using creatinine microsensors equipped in a flow-cell cartridge.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.12
• /
• pp.691-699
• /
• 2004

SRM(Switched Reluctance Motor) drives require the accurate position information of the rotor. These informations are generally provided by a tacho generator or digital shaft-position encoder These speed sensors lower the system reliability and require special attention to noise. This paper describes a new approach to estimating SRM speed from measured terminal voltages and currents for speed sensorless control. The described method is based on the sliding mode observer. The rotor speed and position observers are estimated by the adaptation law using the real and estimated currents. However, the conventional adaptive sliding mode observer based on the variable structure control theory has some disadvantages that the estimated values including the high-frequency chattering and the steady state error generated due to the infinite feedback gain chosen and the discontinuous control input. To reduce the chattering and steady state error, an integrator is also inserted in the sliding mode observer strategy. The described adaptive sliding mode observer decreases the vibration to the switching hyper-plane of the sliding mode by adding integrator. The described methodology incorporates the Lyapunov algorithm to drive the rotor speed and the stator resistance such that it can overcome the problem of sensitivity in the face of SRM parameter variation. Also, without any mechanical information. The rotor speed of SRM is obtained form adaptive scheme. The described method is verified through the simulation and experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10b
• /
• pp.858-863
• /
• 1988

A micro-processor based control system for a brushless DC motor used in the motor-driven electromechanical total artificial heart was developed. Functionally, the control system is composed of two parts. The first part is the velocity and position controller to assure that the motor follows a predetermined optimal velocity profile with minimal energy consumption, and to guarantee the full stroke length. This part also utilize the passive adaptive control method to be robust against the load disturbance, system parameter variation, and uncertainty which is the environment of artificial heart system. The pump output control is the second part, and this part provides the required responses of the artificial heart to the time-varying physiologic demands. The basic requirements of these responses are preload sensitivity, afterload insensitivity, and the balanced ventricular outputs. The performance and reliability of this control system was evaluated through a series of mock circulation tests and animal implantation, and the results are very encouraging.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.737-741
• /
• 2003

The wind power system is spotlighted as one of the no-pollution power generation systems. The system uses winds as power source that are rotated the blade and the rotating power from blade generate the electricity power. Gearbox needs to transfer the wind powers that have the high-torque-low-speed characteristics to generator that have the low-torque-high-speed characteristics. Because the wind power system generally locates the remote place like seaside or mountainside and the gearbox installs on the limited and high placed space, the gearbox of the wind power system is required the optimal space design and high reliability. In this paper, the structure of the gearbox is proposed to achieve the optimal space and efficiency by compounding the planetary gear train that has the high power density and parallel type gear train that has the long service life. The design parameters that are affected the service life are studied. The gear ratio and face width are investigated as an affected parameter for design sensitivity of service life.