• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.4
• /
• pp.318-325
• /
• 1995

Information of change of hardness values during applying load is needed often to control the quality of metal products efficiently, but the relation between applied stress and hardness has not been established. In this paper the theoretical relation between the rebound hardness and stress was examined briefly and the experiment was performed with some materials. Materials used in test were mild steel(SB41), 7-3 brass and copper, which were widely used in the commercial plants. Hardness was measured during stress applied using the Equo-Tip hardness tester as a kind of rebound hardness tester. Hardness values decreased as tensile stress increased, the decreasing rate was effected by the Young's modulus of each material, and the rebound hardness values showed linear relationship with the applied stress in elastic region.

• Architectural research
• /
• v.20 no.4
• /
• pp.137-145
• /
• 2018

The nondestructive test is widely used in the field of diagnosis and maintenance to evaluate the degree of damaging of structures caused by aging, and the demand for this test method is expected to continue increasing. However, there is a lack of standards related to the nondestructive test, and South Korea is relying heavily on developed nations for original technologies related to diagnosis. It is an urgent task to establish a nondestructive test method appropriate for the circumstance of South Korea. The purpose of this study is to compare and analyze estimated error of compressive strength in single-story structures comprised of vertical and horizontal reinforced concrete members using the impact testing method and rebound hardness method, which are nondestructive test methods, and to review on-site applicability of these methods. Based on compressive strength of the structures estimated, overall mean error was 21.2% for the impact testing method and 15.6% for the rebound hardness method. The necessity of a reliable diagnostic method based on compound nondestructive test methods to increase accuracy of estimation was confirmed.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.4
• /
• pp.655-661
• /
• 2020

In this study, the correlation between concrete core compressive strength and rebound hardness of urban railway underground structures was analyzed. The equations for the range of rebound hardness were derived and compared with the measured concrete core strengths for each range of rebound hardness to confirm the adequacy of the estimated compressive strength. As the result, the linear regression analysis results of the average compressive strength by the Gaussian probability density function (representative compressive strength estimation formula) and the estimation formula by the rebound hardness range were founded to match well within 3% of the experimental concrete core compressive strength test results. Therefore, the stochastic statistical analysis using the rebound hardness measurement results suggested in this study could be help to secure the confidence level of the correlation between the rebound hardness and the concrete compressive strength which are relatively large deviation according to the estimation equations.

• Journal of the Korean Institute of Gas
• /
• v.21 no.3
• /
• pp.26-32
• /
• 2017

Outer tank concretes of LNG storage tank are composed of prestressed concrete structures that act as a protective wall. The danger such as the collapse of structures will exist if concrete structures is not secured due to the deterioration. Concrete compressive strength directly related to the safety of structures can be predicted by using estimation equation of compressive strength through rebound hardness test and ultrasonic wave velocity method. But, there is no the estimation equation of LNG storage tank for a relation between NDT data and real strength. In this study, to obtain more accurate real strengths for LNG storage tank, core specimens were sampled from walls of pilot LNG storage tank. The rebound hardness test of general NDT for concrete structures was carried out at each 3 positions for the four areas. The compressive strength estimation equation of LNG storage tank was developed by using the data for rebound hardness test of pilot LNG storage tank and compressive strength test of sampled concrete cores.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.783-786
• /
• 1999

The compressive strength of concrete is one of the most important properties in concrete structures. There are, two methods for the testing of concrete compressive strength in structure ; coring and nondestructive testing. The latter is more often used than the former in a view of time and expenses. The Nondestructive test methods used nowadays include Rebound Hammer test and Ultrasonic Pulse Velocity test. Carbonation through aging makes changes of the interior structure and the properties of concrete. It is well-known fact that the surface hardness of concrete is increased by its carbonation. This fact makes it difficult in estimating the compressive strength of concrete using Rebound Hammer test. This study aimed to quantitatively analyzed the effects of carbonation on results of the Rebound Hammer test.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.2
• /
• pp.143-151
• /
• 2022

In this study the relative dynamic modulus and surface rebound hardness measurement methods were used for comparison to predict the occurrence of frost dam age on the concrete. From the test results, it was observed that the initiation of concrete dam age predicted by surface rebound hardness values was 200 cycles quicker than that of the relative dynamic modulus method in the W/C 70 specimens. In addition, it continuously provided data that showed the frost damage development of concrete surfaces according to increasing freeze-thaw cycles. This indicated that the frost dam age of the concrete could be found from the initial point of its occurrence by the surface rebound hardness measurement method. Similar results were also observed in W/C 60 and 50 specimens. Therefore, it is considered that surface rebound hardness method predicted the freeze-thaw damage well, regardless of water-cement ratio.

• Journal of the Korean Society of Safety
• /
• v.32 no.5
• /
• pp.62-68
• /
• 2017

It is necessary to analyze on the compressive strength among material properties of concrete for confirming damages of architectures due to large explosion. A non destructive test is known as the representative methods estimating compressive strength and ultrasonic pulse velocity, rebound hardness test are widely used because of their simplicity, convenience. But combined method supplementing two types is applied at now as they are affected by the characteristics of test specimen. In this research to check damages on the members of structure before and after explosion, the characteristics of compressive strength are compared and analyzed through a real explosion test prior to full scale structures. The test results showed that the larger the TNT powder and the shorter the distance, the greater the decrease in strength before and after the explosion and that the largest displacement and moment for the explosive load and the greatest decrease in the strength at the central part. Due to the surface condition and the thickness variation of the concrete specimens, the standard deviation value is the smallest in the combining method of fusion of the ultrasonic method and rebound hardness method. Thus, the combining method can be one of appropriate methods to evaluate the strength in the reinforced concrete structures damaged by the explosion.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.109-116
• /
• 2000

Rippability refers to the ease of excavation by construction equipment. Since it is related to rock quality in terms of hardness and fracture density, which may be measured by seismic refraction surveys, correlations have been made between rippability and seismic P wave velocities. The 1-channel signal enhancement seismograph(Bison, Model 1570C) was used to measure travel time of the seismic wave through the ground, from the source to the receiver. The seismic velocity measurement was conducted with 153 lines at 5 rock slopes of Chungbuk Youngdong area. Schmidt rebound hardness test were conducted with 161 points on rock masses and the point load test also on 284 rock samples. The uniaxial compressive strength and seismic wave velocity of 60 rock specimens were measured in laboratory. These data were used to evaluate the rock quality of 5 rock slopes.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.69-70
• /
• 2013

This is an foundational study to adequacy the non-destruction testing for the estimation of compressive strength of high strength concrete The results are as follows, In high strength concrete, H type is NR type rebound number rather than higher. The relation between rebound number and compressive strength of high strength concrete have lower coefficient. when compressive strength estimation of high strength concrete, it consider that rebound hardness test is not applied and should be consider to combined method or addition method.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.1
• /
• pp.61-71
• /
• 2004

The performance evaluation and deflection of 3 spans concrete simplicity slab bridge analyzed by non-destructive and loading test. Compressive strength of slab and pier appeared in the range of each 353∼366 kgf/$cm^2$ and 152∼215 kgf/$cm^2$ in rebound number test. Also, it appeared that concrete quality of slab was good after performance improvement. The average compressive strength of slab by core picking appeared 229 kg/$cm^2$. In reinforcing bar arrangement test of span and member, it appeared that horizontal and vertical reinforcing bar was arranged to fixed interval. The value of calculation deflection that carried structural analysis with deflection analysis wave in static loading test appeared higher than that of experimental deflection and it appeared that hardness of this bridge was good. Maximum impact factor that estimated from deflection by running speed in dynamic loading test appeared by 0.216 in 10 km/hr running speed.