• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.130-133
• /
• 2008

The formability of DP steels can be affected by not only initial texture but also deformation texture evolved during plastic deformation. To investigate the evolution of deformation texture during deep drawing, deep drawing process for DP steels was carried out experimentally. A rate sensitive polycrystal model was used to predict texture evolution during deep drawing process. In order to evaluate the strain path during deep drawing, a steady state was assumed in the flange part of deep drawn cup. A rate sensitive polycrystal model successfully predicted the texture development in DP steels during deep drawing process. It was found that the final stable orientations were strongly dependent on the initial location in the blank.

• Journal of Mechanical Science and Technology
• /
• v.17 no.3
• /
• pp.422-428
• /
• 2003

This study concerns the performance of the heat transfer of the thermosyphons having 60, 70, 80. 90 axial internal low-fins in which boiling and condensation occurr. Water, HCFC-141b and CFC-11 have been used as the working fluids. The operating temperature, the liquid charge ratio and the inclination angle of thermosyphons have been used as the experimental parameters. The heat flux and heat transfer coefficient at the condenser are estimated from experimental results. The experimental results have been assessed and compared with existing theories. As a result of the experimental investigation, it was found that the maximum heat flow rate in the thermosyphons is dependent upon the liquid charge ratio and inclination angle. A relatively high rate of heat transfer has been achieved by the thermosyphon with axial internal low-fins. The inclination of a thermosyphon has a notable influence on the condensation. In addition, the overall heat transfer coefficients and the characteristics at the operating temperature are obtained for the practical applications.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 1998.11a
• /
• pp.269-276
• /
• 1998

This paper proposes an opportunistic age replacement policy. The system has two types of failures. Type I failures (minor failures) are removed by minimal repairs, whereas type II failures are removed by replacements. Type I and type II failures are age-dependent. A system is replaced at type II failure (catastrophic failure) or at the opportunity after age T, whichever occurs first. The cost of the minimal repair of the system at age z depends on the random part C(z) and the deterministic part c(z). The opportunity arises according to a Poisson process, independent of failures of the component. The expected cost rate is obtained. The optimal $T^{\ast}$ which would minimize the cost rate is discussed. Various special cases are considered. Finally, a numerical example is given.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.767-772
• /
• 2003

The clay which transported into a pond under the high water content condition have no effective stress which develop from the starting point of sedimentation and self-weight consolidation. Since sedimentation and self-weight consolidation dependent on self-weight of solids is made progress over a long time, to accelerating it have many advantages in the economic view In this paper, sand spreading method which is one of sedimentation and self-weight consolidation acceleration method is studied through a series of experiments considering the mixing ratio of sand and clay. The test results show that the mixing ratio of clay and sand of 1:0.2 is the biggest rate of consolidation and the pouring at the end point of sedimentation considerably effects on consolidation rate.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.231-234
• /
• 2009

Based on combined continuum-fracture mechanics, fracture criterion was utilized to predict impact performance of advanced high-strength steel sheets: 340R and TWIP940. The macro-crack propagation behavior at high stress triaxiality was characterized by V-notch tests while deformation behavior at high strain rate was characterized by simple tension tests with various cross head speeds. The characterized mechanical properties were incorporated into the FE program ABAQUS/Explicit to simulate the charpy impact tests, which showed good agreement with experiments.

• Microbiology and Biotechnology Letters
• /
• v.17 no.4
• /
• pp.277-282
• /
• 1989

Xanthan gum is a biopolymer produced by Xanthomonas campestris. In xanthan gum fermentation, the fermentation broth changes to highly viscous non-Newtonian fluid as xanthan gum concentration increases. Maximum xanthan gum concentration is limited by high viscosity of the broth since mass transfers of nutrient and oxygen are inhibited. Int this study the mass transfer effects were investigated in batch and fed-batch fermentations at various agitation speeds and by separate oxygen transfer experiments. Xanthan gum production rate was observed to be largely dependent on oxygen transfer coefficient; while cell growth rate was not affected highly by this factor.

• Journal of the Korean Ceramic Society
• /
• v.24 no.5
• /
• pp.461-469
• /
• 1987

Single crystals of Mn-Zn Ferrite were grown by slow cooling method using Na2B4O7 as flux agent. The effects of flux content and cooling rate on the types of crystals, and the relation between supersaturation and growth mechanism were studied. As a result, the types of grown crystals occurred as plate, hopper and octahedral crystals. The occurrence of these crystal types was dependent on flux content. The habit was found to correlate with the growth rate and supersaturation. The lateral growth of a dendritic crystal is related to the twin layer. The growth of crystals from borax melts mainly occurred by the layer-spreading growth following corner and edge nucleation caused by high supersaturation in the melt. Especially, the plate crystals were produced on top of the melts. The hopper and octahedral crystals occurred at lower supersaturation than the plate crystals.

• Journal of Environmental Science International
• /
• v.11 no.6
• /
• pp.561-567
• /
• 2002

This study was investigated to evaluate the effect of the sodium ion and pH on toxicity of dinitrophenol at high concentrations (0.41 to 0.54 mM), over a sodium concentration range of 0.1 mM to 107 mM and over a pH range of 5 to 9. The concentration of sodium ions in the activated sludge mixed liquor seemed to have very little effect on dinitrophenol toxicity. However, lack of sodium in the growth media resulted in a reduction of the dinitrophenol degradation rate by bacterial isolate from the activated sludge culture, which has been identified as Nocardia asteroides. Dinitrophenol inhibition was found to be strongly dependent on mixed liquor pH. The dinitrophenol degradation rate was highest in the pH range of 6.95 to 7.84; at pH 5.94 degradation of 75 mg/L dinitrophenol was significantly inhibited; at pH < 5.77, dinitrophenol degradation was completely inhibited after approximately 30% of the dinitrophenol was degraded.

• KSBB Journal
• /
• v.17 no.3
• /
• pp.307-310
• /
• 2002

In order to obtain high density seed cells for biofiltration, we studied batch and fed-batch culture of P. putida. Studies were carried out to find optimum fermentation conditions such as pH, concentration of glucose and agitation speed. Specific growth rate of P. putida was dependent on agitation speed and a high rpm of 300 was necessary to carry out the efficient aerobic growth of P. putida. Specific growth rate was highest at pH 7. Feeding glucose and yeast extract continuously at the initial growth phase was the most effective way to get high cell density of P. putida.

• 한국생물공학회:학술대회논문집
• /
• 2003.04a
• /
• pp.223-227
• /
• 2003

Mevinolic acid (MA), a secondary metabolite produced by a filamentous fungus Aspergillus terreus, is acidic form of lovastatin which has been identified as a powerful cholesterol-lowering agent in humans. When immobilized cell culture was performed, MA production was about 5.3-fold higher than the parallel suspended cell culture. Although the immobilized cells proliferated slowly during exponential in comparison with the suspended cells, oxygen uptake rate and oxygen mass transfer coefficient of the immobilized cell culture were about 1.3- and 2.5- fold higher respectively than those of the parallel suspended cell culture. From these results, it was concluded that MA biosynthesis was closely dependent on the cell growth rate, morphology and oxygen availability.