• 전자공학회논문지A
• /
• 제30A권11호
• /
• pp.105-112
• /
• 1993

Oxide and reoxidized-nitrided-oxide were formed by furnace oxidation and rapid thermal processing (RTP). MOS capacitor and n-MOSFET's with those films as gate insulators were fabricated. The electrical characteristics of insulators were evaluated by current-voltage, high-frequency capacitance-voltage (C-V), and time-dependent dielectrical breakdown (TDDB) measurements. The hot carrier effects of MOSFET's were also investigated. Time-dependent dielectrical breakdown (TDDB) characteristics show that the life time of reoxidized-nitrided-oxide films is about 3 times longer than that of oxides. Hot carrier effects reveal that the life time of MOSFET's with reoxidized-nitrided-oxides is about 3 times longer than that of MOSFET's with oxides. Therefore, it is found that the reliability of dielectric films estimated by the hot carrier effects of MOSFET's is consistent with that of dielectric films from TDDB method.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 추계학술대회 논문집
• /
• pp.76-78
• /
• 2003

We have designed and tested an RSFQ (Rapid Single Flux Quantum) NDRO (Non Destructive Read Out) circuit for the development of a high speed superconducting ALU (Arithmetic Logic Unit). When designing the NDRO circuit, we used Julia, XIC and Lmeter for the circuit simulations and layouts. We obtained the simulation margins of larger than $\pm$25％. For the tests of NDRO operations, we attached the three DC/SFQ circuits and two SFQ/DC circuits to the NDRO circuit. In tests, we used an input frequency of 1 KHz to generate SFQ Pulses from DC/SFQ circuit. We measured the operation bias margin of NDRO to be $\pm$15％. The circuit was measured at the liquid helium temperature.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.24-29
• /
• 2002

In any rapid prototyping process, the layer by layer building process introduces an area error between the staircase and the surface line specified by the computer-aided design model. This affects the dimensional accuracy as well as the surface finish for different part build orientations. This paper describes a methodology for computing the area error for any orientation of the part built by the fused deposition modelling system. This technique can be applied to determine the best build orientation of the part, based on the minimum area error. This technique is verified by comparing the results with the experimental measurements of the area error of the parts built at different orientations.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -2
• /
• pp.902-905
• /
• 2000

Because of the rapid growth of Internet and multimedia applications, how to protect IPR (intellectual property rights) has become a critical issue. Is one of the ways to overcome the problem of the protection of IPR. Digital watermarking call be applied to multimedia data, such as digital images, digital video, and digital audio. In this paper, we propose a digital watermarking technique for digital images to authenticate an owner or an image by embedding visually recognizable patterns, such as logos, signatures, or stamps into images In BDCT (block discrete cosine transform) frequency domain. The proposed method sorts the components of an original image twice. At the same time, the method, also, rearranges the components of a watermark twice in order to be more robust, and finally embeds the watermark into the image. From the experimental results, the conjunction of three similarity measurements shows that our proposed method is robust to image cropping, image filtering, and JPEG (the Joint Photographic Experts Group) both subjectively and objectively.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.227-233
• /
• 1999

Detailed Measurements were made to investigate the turbulence characteristics of a leakage vortex in an axial-flow fan using three-dimensional LDV. The turbulence in the leakage vortex has highly anisotropic characteristics with the radial value being the maximum. The turbulence intensity components in the vortex in the streamwise and tangential directions increase up to a certain downstrean position and then decrease. This increase is mainly due to the rapid decrease of the streamwise velocity of the vortex and partly due to the radial gradient of the streamwise velocity caused by a velocity deficit. As the vortex decays moving downstream, turbulence intensity also decrease gradually.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권4호
• /
• pp.208-212
• /
• 2004

In this paper, the characteristics of co-sputtered Ru-Zr metal alloy as gate electrode of MOS capacitors have been investigated. The atomic compositions of alloy were varied by using the combinations of relative sputtering power of Ru and .Zr. C-V and I-Vcharacteristics of MOS capacitors were measured to find the effective oxide thickness and work function. The alloy made of about 50% of Ru and 50% of Zr exhibited an adequate work function for nMOS. C-V and I-V measurements after 600 and $700^{\circ}C$ rapid thermal annealing were performed to prove the thermal and chemical stability of the Ru-Zr alloy film. Negligible changes in the accumulated capacitance and work function before and after annealing were observed. Sheet resistance of Ru-Zr alloy was lower than that of poly-silicon. It can be concluded that the Ru-Zr alloy can be a possible substitute for the poly-silicon used as a gate of nMOS.

• 대한치과의사협회지
• /
• 제55권5호
• /
• pp.358-364
• /
• 2017

Nowadays, there has been an increasing interest in the preservation of natural dentition and the proper occlusion related to tooth wear for quality of life. Tooth wear means the loss of tooth enamel structure. This is happened by many causes which is the combined effects of many mechanisms. For keeping proper occlusion, dentists should check tooth wear status with acceptable methods and tools for the proper diagnosis. Until now, there have been many traditional qualitative ways to measure tooth wear which are intuitive, rapid, and simple. On the contrast, they are not objective nor reproducible. With the development of related technique, new quantitative methods using CAD and 3d scanners. This article aimed to introduce qualitative and quantitative methods for tooth wear measurements.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1990년도 추계학술대회 논문집
• /
• pp.81-85
• /
• 1990

$WSi_{x}$ film deposited on p+ polysilicon by low pressure chemical vapor deposition method were annealed by rapid thermal process, their properties have been investigated by measurements of electrical resistivity and Hall voltage and by analyses of phases and microstructure using X-ray diffraction and SEM technique. The electrical resistivity of the polycides consisting of the tungsten silicide and the p+ polysilicon decreases with the increase in annealing temperature due probably to the increase in grain size. unlike the polycides consisting of the $WSi_{x}$ and n+ polysilicon, however, the Hall voltage of the polycides consisting of $WSi_{x}$ and p+ polysilicon were positive for all specimens annealed as well as the as-deposited one, indicating the majority carrier in $WSi_{x}$. is hole and is independent of the annealing.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1996년도 춘계학술대회
• /
• pp.235-239
• /
• 1996

In recent years, the optical properties of multiple-scattering media like tissue have been studied for their potential applications in medicine. In this work the optical properties of multiple scattering media were investigated using the time-resolved reflectance measurement. The reflected light was measured by time-correlated single photon counting system. The transport scattering and absorption coefficient are related to the initial rapid decay and the subsequent decay in reflected light, respectively. Also the optical properties of the samples were measured by conventional method, ie., using continuous wave light. When the distance between the light source and the detector is over 8mm, the optical coefficient can be measured accurately using the suggested method.

• Communications for Statistical Applications and Methods
• /
• 제12권2호
• /
• pp.335-348
• /
• 2005

The rapid development of microarray technologies enabled the monitoring of expression levels of thousands of genes simultaneously. Recently, the time course gene expression data are often measured to study dynamic biological systems and gene regulatory networks. For the data, biologists are attempting to group genes based on the temporal pattern of their expression levels. We apply the consensus clustering algorithm to a time course gene expression data in order to infer statistically meaningful information from the measurements. We evaluate each of consensus clustering and existing clustering methods with various validation measures. In this paper, we consider hierarchical clustering and Diana of existing methods, and consensus clustering with hierarchical clustering, Diana and mixed hierachical and Diana methods and evaluate their performances on a real micro array data set and two simulated data sets.