• Korean Journal of Materials Research
• /
• v.23 no.1
• /
• pp.47-52
• /
• 2013

Graphene has been synthesized on 100- and 300-nm-thick Ni/$SiO_2$/Si substrates with $CH_4$ gas (1 SCCM) diluted in mixed gases of 10% $H_2$ and 90% Ar (99 SCCM) at $900^{\circ}C$ by using inductively-coupled plasma chemical vapor deposition (ICP-CVD). The film morphology of 100-nm-thick Ni changed to islands on $SiO_2$/Si substrate after heat treatment at $900^{\circ}C$ for 2 min because of grain growth, whereas 300-nm-thick Ni still maintained a film morphology. Interestingly, suspended graphene was formed among Ni islands on 100-nm-thick Ni/$SiO_2$/Si substrate for the very short growth of 1 sec. In addition, the size of the graphene domains was much larger than that of Ni grains of 300-nm-thick Ni/$SiO_2$/Si substrate. These results suggest that graphene growth is strongly governed by the direct formation of graphene on the Ni surface due to reactive carbon radicals highly activated by ICP, rather than to well-known carbon precipitation from carbon-containing Ni. The D peak intensity of the Raman spectrum of graphene on 300-nm-thick Ni/$SiO_2$/Si was negligible, suggesting that high-quality graphene was formed. The 2D to G peak intensity ratio and the full-width at half maximum of the 2D peak were approximately 2.6 and $47cm^{-1}$, respectively. The several-layer graphene showed a low sheet resistance value of $718{\Omega}/sq$ and a high light transmittance of 87% at 550 nm.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.785-791
• /
• 2002

The effect of the supercritical carbon dioxide (sc$CO_2$) on ion-conductive behaviors for polyether electrolytes based on, both poly (ethylene oxide) (PEO) and poly [oligo (oxyethylene glycol) methacrylate] (PMEO) with lithium triflate, LiCF$_3$SO$_3$, has been investigated. In particular, the present research is a new concept for improving the ionic conductivity of polyether electrolytes. The maximum ionic conductivity ($\sigma$$_{max}$) at room temperature of the PEO electrolyte was more than 100 times higher, and the $\sigma$$_{max}$ at 9$0^{\circ}C$ of the PMEO electrolyte was 30 times improved by the se$CO_2$ treatment, respectively. It was revealed that the penetration of $CO_2$ molecules into the polymer matrix causes the increase of carrier ions by ion-dispersion effect and the decrease of glass transition temperature (T$_{g}$) by plasticizing effect that results in the improvement of the ion transport behaviors.viors.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.659-659
• /
• 2013

Recently, graphene has been intensively studied due to the fascinating physical, chemical and electrical properties. It shows high carrier mobility, high current density, and high thermal conductivity compare with conventional semiconductor materials even it has single atomic thickness. Especially, since graphene has fantastic electrical properties many researchers are believed that graphene will be replacing Si based technology. In order to realize it, we need to prepare the large and uniform graphene. Chemical vapor deposition (CVD) method is the most promising technique for synthesizing large and uniform graphene. Unfortunately, CVD method requires transfer process from metal catalyst. In transfer process, supporting polymer film (Such as poly (methyl methacrylate)) is widely used for protecting graphene. After transfer process, polymer layer is removed by organic solvents. However, it is impossible to remove it completely. These organic residues on graphene surface induce quality degradation of graphene since it disturbs movement of electrons. Thus, in order to get an intrinsic property of graphene completely remove of the organic residues is the most important. Here, we introduce modified wet graphene transfer method without PMMA. First of all, we grow the graphene from Cu foil using CVD method. And then, we deposited several metal films on graphene for transfer layer instead of PMMA. Finally, we fabricate graphene FET devices. Our approaches show low defect density and non-organic residues in comparison with PMMA coated graphene through Raman spectroscopy, SEM and AFM. In addition, clean graphene FET shows intrinsic electrical characteristic and high carrier mobility.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.208-208
• /
• 2013

Graphene has emerged as a fascinating material for next-generation nanoelectronics due to its outstanding electronic properties. In particular, graphene-based field effect transistors (GFETs) have been a promising research subject due to their superior response times, which are due to extremely high electron mobility at room temperature. The biggest challenges in GFET applications are control of carrier concentration and opening the bandgap of graphene. To overcome these problems, three approaches to doping graphene have been developed. Here we demonstrate the decoration of Ni nanoparticles (NPs) on graphene films by simple annealing for p-type doping of graphene. Ni NPs/graphene films were fabricated by coating a $NiCl2{\cdot}6H2O$ solution onto graphene followedby annealing. Scanning electron microscopy and atomic force microscopy revealed that high-density, uniformly sized Ni NPs were formed on the graphene films and the density of the Ni NPs increased gradually with increasing $NiCl2{\cdot}6H2O$ concentration. The formation of Ni NPs on graphene films was explained by heat-driven dechlorination and subsequent particlization, as investigated by X-ray photoelectron spectroscopy. The doping effect of Ni NPs onto graphene films was verified by Raman spectroscopy and electrical transport measurements.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.99-99
• /
• 2013

나노결정질 다이아몬드(Nanocrystalline Diamond: NCD) 박막은 고경도와 낮은 마찰계수를 가지고 있어 초경합금이나 고속도강과 같은 절삭공구 위에 코팅하여 공구의 성능 향상을 도모하려는 노력이 있어 왔다. 그러나 NCD 박막의 잔류응력이 크고, 초경합금과 철계 금속에 NCD가 증착되지 않는다는 문제점이 있다. 따라서 잔류응력 완화와 다이아몬드 핵생성을 위하여 제3의 중간층 재료가 필요하다. 본 연구에서는 W과 Ti을 중간층으로 하여 초경합금(WC-Co)과 고속도강(SKH51)에 NCD 박막을 코팅하고 기계적 특성을 비교하였다. 초경합금 또는 고속도강기판 위에 W 또는 Ti 중간층을 DC magnetron sputter를 이용해 각 1 ${\mu}m$의 두께로 증착하고 그 위에 MPCVD (Microwave Plasma Chemical Vapor Deposition)를 이용해 NCD 박막을 2${\mu}m$의 두께로 코팅하였다. FESEM을 이용하여 표면과 단면의 형상을 관찰하였고, XRD와 Raman spectroscopy를 통해 NCD 박막의 결정성을 확인하였다. 그리고 tribology test를 실시하여 코팅된 박막의 내마모성을 비교하였으며, Rockwell C indentation test를 이용하여 밀착력을 비교하였다. 초경합금에 적용 시, W이 Ti보다 중간층으로서 더 우수한 것으로 나타났으며 이는 열팽창계수 차이에 의한 잔류응력의 차이에 의한 것으로 여겨진다. 중간층 두께에 따른 박막의 기계적 특성 변화를 알아보기 위해 W 중간층의 두께를 1, 2, 4 ${\mu}m$로 변화를 주었다. 중간층 두께가 2 ${\mu}m$ 이상일 때 박막의 밀착력이 증가되는 것으로 나타났다. 고속도강 위에 같은 방법으로 1 ${\mu}m$의 W 또는 Ti 중간층 위에 2 ${\mu}m$의 NCD 박막을 코팅한 시편들은 초경합금에 코팅한 것과 달리 두 시편 모두 낮은 밀착력을 나타내었다. 열팽창계수 차이에 의한 잔류응력을 완화하기 위해 고속도강에 W/Ti 복합박막을 중간층으로 Ti, W순으로 각각 1 ${\mu}m$ 두께로 증착 후 그 위에 NCD 박막을 2 ${\mu}m$ 두께로 코팅 한 후 특성을 비교하였다. Ti/W 복합 중간층 위에 코팅된 NCD 박막의 밀착력이 W 혹은 Ti 단일 중간층에 코팅된 박막에 비해 우수한 것으로 나타났다. 그러나 실제 공구에 적용하기에는 박막의 밀착력 개선이 요구되며 이를 위해서 더 연구가 필요하다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.630-630
• /
• 2013

Recently, atomically smooth hexagonal boron nitride(h-BN) known as a white graphene has drawn great attention since the discovery of graphene. h-BN is a III-V compound and has a honeycomb structure very similar to graphene with smaller lattice mismatch. Because of strong covalent sp2bonds like graphene, h-BN provides a high thermal conductivity and mechanical strength as well as chemical stability of h-BN superior to graphene. While graphene has a high electrical conductivity, h-BN has a highly dielectric property as an insulator with optical band gap up to 6eV. Similar to the graphene, h-BN can be applied to a variety of field, such as gate dielectric layers/substrate, ultraviolet emitter, transparent membrane, and protective coatings. However, up until recently, obtaining and controlling good quality monolayer h-BN layers have been too difficult and challenging. In this work, we investigate the controlled synthesis of h-BN layers according to the growth condition, time, temperature, and gas partial pressure. h-BN is obtained by using chemical vapor deposition on Cu foil with ammonia borane (BH3NH3) as a source for h-BN. Scanning Transmission Electron Microscopy (STEM, JEOL-JEM-ARM200F) is used for imaging and structural analysis of h-BN layer. Sample's surface morphology is characterized by Field emission scanning electron microscopy (SEM, JEOL JSM-7100F). h-BN is analyzed by Raman spectroscopy (HORIBA, ARAMIS) and its topographic variations by Atomic force microscopy (AFM, Park Systems XE-100).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.12
• /
• pp.776-780
• /
• 2015

In this paper, we have studied the effect of mechanical polishing to Ga-polar face for reducing the wafer bowing and strain in free-standing GaN. After the mechanical polishing to Ga-polar face, the bowing of the free-standing GaN substrate significantly decreased with increasing the size of diamond slurry, and eventually changed the bowing direction from concave to convex. Furthermore, the full width at half maximum (FWHM) of high-resolution X-ray diffraction (HR-XRD) were decreased, especially the FWHM of (1 0 2) reflection for $1.0{\mu}m$ size of diamond slurry was significantly decreased from 630 to 203 arcsec. In the case, we confirmed that the compressive strain in Ga-polar face was fully released by Raman measurement.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.2
• /
• pp.193-199
• /
• 2000

The a-C : H films have been grown on the glass substrate by PECVD method, where plasma was generated with a 60 Hz line power source. The growth rate of films is found to be dependent of the partial pressure of $C_2H_2$. This growth rate is a little higher than that in which $CH_4$ instead of $C_2H_2$ is used. The transmittance is also much higher(95%). The optical energy gap of films is in the range of 1.4~1.8eV depending on the partial pressure of $C_2H_2$. However, this energy gap, which is 1.8eV, is found to be independent of the partial pressure of $C_2H_2$ for the thick films above $2000{\AA}$. The carbonization is checked from peak intensities of D ($sp^3$) and G($sp^2$) peaks in Roman spectra. The hydronization and C-H bonding status in films can also be determined from FTIR results. Both the bonding strength of C-H and the ratio of $sp^3$ to $sp^2$ in bonding are found to be slightly dependent of partial pressure of $C_2H_2$. Judging from above results, we can conclude that the best value for partial pressure of $C_2H_2$ in growing process of thick films is about 13.8%.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.6
• /
• pp.297-302
• /
• 2015

Nanocrystalline diamond(NCD) coated aluminium plates were prepared and applied as heat sinks for LED modules. NCD films were deposited on 1 mm thick Al plates for times of 2 - 10 h in a microwave plasma chemical vapor deposition reactor. Deposition parameters were the microwave power of 1.2 kW, the working pressure of 90 Torr, the $CH_4/Ar$ gas ratio of 2/200 sccm. In order to enhance diamond nucleation, DC bias voltage of -90 V was applied to the substrate during deposition without external heating. NCD film was identified by X-ray diffraction and Raman spectroscopy. The Al plates with about 300 nm thick NCD film were attached to LED modules and thermal analysis was carried out using Thermal Transient Tester (T3ster) in a still air box. Thermal resistance of the module with NCD/Al plate was 3.88 K/W while that with Al plate was 5.55 K/W. The smaller the thermal resistance, the better the heat emission. From structure function analysis, the differences between junction and ambient temperatures were $12.1^{\circ}C$ for NCD/Al plate and $15.5^{\circ}C$ for Al plate. The hot spot size of infrared images was larger on NCD/Al than Al plate for a given period of LED operation. In conclusion, NCD coated Al plate exhibited better thermal spreading performance than conventional Al heat sink.

• Journal of the Korean Chemical Society
• /
• v.60 no.1
• /
• pp.28-33
• /
• 2016

The spiropyran is a typical material having photodegradation properties in the process of photochromism. The spiropyran has been utilized in various applications such as optical switch, optical memories, and biosensor because of its remarkable stability, fast responsive time, stronger color change, and photo-induced controllability. However, the spriropyran is photodegraded by the repetitive optical irradiation. The photodegradation of spiropyran have been investigated by using UV-Visible spectroscopy, nuclear magnetic resonance (NMR), and Raman spectroscopy. Herein, the properties of spiropyran were characterized by using terahertz time-domain spectroscopy (THz-TDS) in the terahertz frequency region. In terahertz region, the measured absorbance of spiropyran was increased due to the photodegradation induced by the repetitive UV irradiation. The absorbance tendency of spiropyran in the terahertz frequency region was compared with that in the visible region, and they were completely opposite to each other.