• Mycobiology
• /
• v.30 no.4
• /
• pp.233-239
• /
• 2002

The main aim of this study is to evaluate the efficiency of two biologically active compounds(Strom and F-760) in control of wheat root rot disease and its causal organisms. Fusarium graminearum, F. oxysporum, F. solani and Bipolaris sorokiniana were used as target organisms. In vitro, the two compounds showed fungicidal effect on all investigated pathogens resulted in suppression of radial growth and mycelial dry weight of them. Under greenhouse conditions, treatment of wheat grains with either Strom or F-760 before cultivation significantly reduced the percent of disease distribution as well as the mean disease rating of plants in both seedling and flowering stages. Fresh and dry weights of plants as well as water maintenance capacity were increased as the result of applying these compounds as seed dressing. Also data showed that the membrane stability of plants was injured as a result of infection with all investigated organisms, while this injury was alleviated when F-760 and Strom were applied. The $K^+$ efflux and the leakage of UV absorbing metabolites was stimulated with fungal infection. However, F-760 and Storm treatment partially retarded the stimulatory effect on leakage of $K^+$ and UV-absorbing metabolites of fungal infected plants. On the other side, the fungal infection had inhibitory effects on pigment fractions(chlorophyll a, b, and carotenoids) biosynthesis in wheat leaves. This retarding effect was partially or completely alleviated as the grains were treated with the applied compounds.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.2
• /
• pp.80-91
• /
• 1995

A theoretical models has been prepared which describes the noise generated by tire/road interaction for the tire structure-borne sound analysis. The model begin with a set of thin shell equations describing the motion of the belt of a radial ply tire, as drived by Bohm('mechanisms of the belted tire', Igeniur-Archiv, XXXV, 1966). Structural quantities required for these equations are derived from material properties of the tire. The rolling shape of a tire is computed from the steady-state limit of these equations. Vibrational response of the tire is treated by the full dependent shell equations. The force input at the tire/road interface is calculated on the basis of tread geometry and distribution of contact patch pressure. Radiation of noise is calculated by a simpson integral. Using the programs, the effect on noise of various tire design variations is computed and discussed. Trends which lead to quiet tire design are identified.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.125-128
• /
• 2008

Atomization characteristics of small LRE-injector spray are investigated by using dual-mode phase Doppler anemometry (DPDA). Velocity, size, number density, and volume flux were measured at various injection pressures along the radial distance to make a close inquiry into spatial distribution characteristic of spray droplets. As the injection pressure increases, the velocity, turbulence intensity, number density, and volume flux of spray droplets become higher, whereas the droplet size ($D_{10}$ or $D_{32}$) gets smaller. Also, velocity and volume flux are proportional to Sauter mean diameter (SMD, $D_{32}$).

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.149-152
• /
• 2009

Spray characteristic parameters such as droplet mean velocity, diameter, and volume flux are measured at various locations of spray in order to investigate the evolutionary feature of droplets exiting from a direct-injection type thruster nozzle-orifice. The experimental results indicate that the large droplets with high velocity at the center of upstream are broken-up into smaller droplets with low velocity due to their continuous momentum loss to surrounding air along with spray evolution toward downstream. Also it is found that the high volume flux expands its distribution in radial direction as a results of spray spreading and dispersion.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1110-1119
• /
• 2020

The Floating Absorber for Safety at Transient (FAST) is a safety device used in the innovative Sodium-cooled Fast Reactor (iSFR). The FAST insert negative reactivity under transient or accident conditions. However, behavior of the FAST is still unclear under transient conditions. Therefore, the existing Floating Absorber for Safety at Transient Analysis Code (FASTAC) is improved to analyze the FAST movement by considering the reactivity and temperature distribution within the reactor core. The current FAST system is simulated under a single control rod withdrawal accident condition. In this investigation, the reactor thermal power does not return to its initial thermal power even if the FAST inserts negative reactivity. Only a 9 K of coolant temperature margin, in the hottest fuel assembly at EOL, can lead to unnecessary insertion of the negative reactivity. On the other hand, the FASTs cannot contribute to controlling the reactivity when normalized radial power is less than 0.889 at BOL and 0.972 at EOL. These simulation results suggest that the current FAST design needs to be optimized depending on its installed location. Meanwhile, the FAST system keeps the fuel, cladding and coolant temperatures below their limit temperatures with given conditions.

• Transactions of Materials Processing
• /
• v.24 no.5
• /
• pp.340-347
• /
• 2015

Multi-pass shape drawing is used to manufacture long products of arbitrary cross-sectional shapes. This process allows smooth surface finishes and closely controlled dimensions of the cross-sectional shape. Tube shape drawing for hollow type products provides material savings and weight reduction. The intermediate die shapes are very important in multi-pass tube shape drawing. In the current paper, the design method for the intermediate dies in a tube shape drawing process is developed using a die offset for corner filling (DOCF) method. Underfill defects are related to the radial velocity distribution of each divided section in the deformation zone. The developed intermediate die shape design was applied to the two-pass tube shape drawing with fixed mandrel for manufacturing a hollow linear motion (LM) guide rail. The proposed design method led to uniform and steady metal flow at each divided section. FE-simulations and experiments were conducted to validate the effectiveness of the proposed method in multi-pass tube shape drawing process.

• Progress in Superconductivity and Cryogenics
• /
• v.7 no.4
• /
• pp.1-3
• /
• 2005

Superconducting $MgB_2$ fibers are in-situ grown by a diffusion method. The fibers are prepared by exposing B filaments to Mg vapor inside a folded Ta foil over a wide range of temperature and growth time. The materials are sealed inside a quartz tube by gas welding. The as - grown fibers are characterized by scanning electron microscopy and energy dispersive x - ray analysis. The fibers have a diameter of about $110{\mu}m$. Surface morphology of the fibers looks dependent on growth temperature and mixing ratio of Mg and B. Radial distribution of Mg ions into B is observed and analyzed over the cross - sectional area. Transport properties of the $MgB_2$ fibers are examined by a physical property measurement system. The $MgB_2$ fibers grown at $900^{\circ}C$ for 2 hours show a superconducting transition at 39.8K with ${\Delta}T_c<$ 2.0 K. Resistance at room temperature $MgB_2$ is 3.745 $\Omega$ and residual resistivity ratio (RRR) is estimated as 4.723.

• Journal of Radiation Protection and Research
• /
• v.29 no.1
• /
• pp.25-31
• /
• 2004

Results of EGS4 based calculations to study the spatial resolution of gas detectors are described. The calculations include radial distribution of electrons generated by photons of various energies penetrating into variable thickness of Ar and Xe gas layers. Given a desired spatial resolution, the maximum allowed thickness of gas layer for each energy level is determined. In order to obtain 0.1mm spatial resolution, the maximum thickness for the Ar gas is found to be 2mm for photon energies below 14keV while the optimum energy of photons for Xe gas with the same thickness is about 45keV. The results of calculations performed to compare the number of electrons generated by CsI coated micro-channel plate and the number of electrons generated by the Ar and Xe gas layers are described. The results show that the number of electrons generated by the gases is about 10 times higher than the one generated by CsI coated micro-channel plate. A few sample gray scale images generated by these calculations are included.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.30.2-30.2
• /
• 2016

M104 (NGC 4594, the Sombrero) is an intriguing disk galaxy classified as an elliptical galaxy nowadays. It hosts a luminous bulge and a massive disk, but it is still mysterious how M104 acquired such peculiar structures. Globular clusters are an useful tracer to investigate the formation history of early-type galaxies. In this study we present a wide field imaging study of the globular clusters in M104. Using wide ($1^{\circ}{\times}1^{\circ}$) and deep ugi images of M104 obtained with the CFHT/MegaCam observations, we detect a large number of globular clusters. The color distribution of these globular clusters shows that there are two subpopulations: a metal-poor system and a metal-rich system. The radial number density of the metal-poor globular clusters shows a long tail reaching R ~ 30' (~ 80 kpc), indicating clearly the existence of a giant metal-poor halo in M104. This result is consistent with the previous studies on the dual halos of massive early-type galaxies. We will discuss implications of these results in relation with the formation history of M104.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.11
• /
• pp.568-576
• /
• 2002

This paper presents a new algorithm for the enhancement of voltage stability by optimal routing (OR) technique. A new voltage stability index (VSI) for optimal routing is also proposed by using theories of critical transmission path based on voltage phasor approach and equivalent impedance method. Furthermore, the proposed algorithm automatically detect the critical transmission path to critical transmission path to critical load which are faced to voltage collapse due to additional real or reactive loading. We also adopt a improved branch exchange (IBE) algorithm based on a tie branch power (TBP) flow equation to apply the OR technique. The proposed IBE algorithm for the VSI maximizing can effectively search the optimal topological structures of distribution feeders by changing the open/closed states of the sectionalizing and tie switches. The proposed algorithm has been evaluated with the practical IEEE 32, 69 bus test systems and KEPCO 148 bus test system to show favorable performance.