• Journal of Information Display
• /
• v.9 no.2
• /
• pp.9-13
• /
• 2008

A novel push-pull voltage converter structure, using a switched capacitor type voltage doubler, is proposed. The circuit is constructed with a two-stage push-pull voltage doubler that has a stable operation with small output ripple. The two-stage voltage doubler creates the output voltage 4Vdd. The high clock signal is cross-coupled to the input of the second stage with the opposite phase to reduce two switching transistors and capacitors. Simulation results verify that even with a reduced number of transistor and capacitor, there is no circuit performance loss. Adding one capacitor and two switching transistors the circuit can be changed to eight times of Vdd maker.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.134-141
• /
• 2004

This paper presents a method of synchronous rectifier(SR) for improving the efficiency in DC/DC converter. The proposed method is used push-pull topology on primary as a single winding self driven synchronous rectification(SWSDSR). Specially, this method can improve efficiency to turn on SR switch during dead time. Finally, the simulation and experimental results will be given to show comparison and analysis on the efficiency between self driven synchronous rectification(SDSR) and SWSDSR method.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.217-220
• /
• 2003

In the case of the remediation studies, push pull test is a more time and cost effective mettled than multi-well tracer test. It also gives Just as much or more information than the traditionally used methods. But the data analysis for the hydraulic parameters, there have been some defections such as underestimation of dispersivity, requirement for effective porosity, and calculation of recovery of center of mass to estimate linear velocity. In this research, Weibull distribution function is proposed to estimate the center of mass of breakthrough curve for Push pull test. The hydraulic parameter estimation using Weibull function showed more exact values of center of mass than those of exponential regression for field test data.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2012.07a
• /
• pp.51-54
• /
• 2012

본 논문에서는 스테레오스코픽 비디오 응용 포맷(Stereoscopic video Application Format)을 기반으로 IP환경에서 3차원 광고, 홍보 및 교육 등에 직접적으로 적용될 수 있는 3D Push 서비스 시스템을 제안한다. 스테레오스코픽 비디오 응용 포맷은 모바일 및 고정형 환경에서 스테레오스코픽 비디오 저장 및 전송을 위한 파일 포맷으로서 다양한 3D 디바이스에 공통으로 적용될 수 있으며 국제표준(ISO/IEC 23000-11)으로 채택되었다. 제안한 시스템은 스테레오스코픽 콘텐츠를 토대로 프로그램 저작을 위한 저작 및 저장을 위한 저작도구, 저작된 프로그램을 스케줄링하고 각 클라이언트의 요청에 따라 전송 관리하는 서버 및 프로그램에 따라 자동 3D 디스플레이 및 사용자 인터랙션을 제공하는 플레이어로 구성된다. 또한, 제안하는 시스템은 국제표준을 토대로 다양한 3D 디바이스와 호환성을 제공하며 모바일 및 고화질 3차원 서비스를 제공할 수 있으며, 각 사이트 과금에 따라 3D 프리미엄 서비스 및 Non-tapeless기반의 원격관리 3D Push 서비스를 제공하는 장점을 가진다.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.275-277
• /
• 1998

The effect of the coil flux, so called "push/pull effect", is to shift the airgap flux density variation due to the magnet alone by a certain amount. Thrust therefore is shift downward or upward. The push/pull effect was presented through the FEM analysis and static tests. We compared with the thrust obtained through the FEM analysis and static tests.

• Steel and Composite Structures
• /
• v.7 no.5
• /
• pp.391-404
• /
• 2007

This paper presents push-out tests of stud shear connectors to examine their fatigue behavior for developing a new composite bridge deck system. The fifteen push-out specimens of D16 mm stud welded on 9 mm steel plate were fabricated according to Eurocode-4, and a series of fatigue endurance test and residual strength test were performed. Additionally, the stiffness and strength variations by cyclic loading were compared. The push-out test, when the stiffness reduction ratio of the specimens was 0.95 under cyclic load, resulted in the failure of the studs. The stiffness variation of the push-out specimens additionally showed that the application of cyclic loads reduced the residual strength. The fatigue strength of the shear connectors were compared with the design values specified in the Eurocode-4, ASSHTO LRFD and JSSC codes. The comparison result showed that the fatigue endurance of the specimens satisfies the design values of these codes.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.594-599
• /
• 2007

This study represents numerical analysis on the fluid flow and concentration characteristics by scattering fume at push-pull ventilation system. And the principal point is making optimum on improve an existing ventilation system. This phenomenon simulated about local ventilation system by using commercial CFD tool and base on these fact has find improvements. Advanced model shows most low different pressure and velocity which are suction capability at inlet surface of pull hood has most uniformity. When compared with existing model, Improved model has more good ventilation performance.

• Journal of Power Electronics
• /
• v.14 no.3
• /
• pp.432-443
• /
• 2014

In order to improve the output efficiency of solar cells and to extend the life span of batteries, the input currents of converters are required to be continuous. If low output voltage ripple is required at the same time, it is obvious that the application of basic two-order converters (such as Buck and Boost derived converters) will not be good enough. In this paper, a lot of non-isolated push-pull converters (NIPPCs) with continuous current will be introduced due to their lower current stress, higher efficiency and better EMC performance. By decomposing the converters into push-pull cells, inductor and free-wheeling diodes, two families of NIPPCs based on single inductor and coupled inductor separately are systematically generated. Furthermore, characteristics analyses for some of the generated converters are also shown in this paper. Finally, two prototypes based on the corresponding typical topologies are built in the lab to verify the theoretical outcomes.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1232-1234
• /
• 2003

The push pull forward converter is a very suitable circuit for low output voltage, high output current applications with a wide input voltage range. This converter can be miniaturized by integrate magnetic components such as the output inductor, the transformer and the input inductor. We considered of the efficiency for the push pull forward converter. Developed the push pull forward converter rating are of $36{\sim}72V$ input and 3.3V/30A output. In this converter. the efficiency was measured by 76.4% at full load and 82.95% at half load. The maximum efficiency is up to 83.% at 200kHz, 11A output.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2002.04b
• /
• pp.1085-1088
• /
• 2002

제7차 교육 개혁 후 초등학생들에게도 컴퓨터를 접할 수 있는 기회가 더 많이 주어졌다. 환경의 변화에 따라 초등학생들을 위한 컴퓨터 교육의 필요성이 대두되고, 개인 수준별 컴퓨터 수업이 필요하게 되었다. 현재 초등학생들을 위한 교육용 프로그램과 인터넷을 활용한 수업이 진행중이나 개인의 수준을 고려한 수업과는 거리가 멀기 때문에 본 논문에서는 초등학교 컴퓨터 수업의 활발한 진행과 개인별 수준을 고려한 수업을 위해 Push 기반 단계별 교육시스템을 제안하였다. 제안한 시스템은 Push 기술을 사용함으로써 능동적 학습참여와 개인별 수준을 고려한 수업이 가능하다는 면에서 7차 교육과정의 교육 목표에 맞는 시스템이라 할 수 있다.