• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.6
• /
• pp.611-616
• /
• 2013

Many researches have been carried out consistently for the green ship owing to its economic increasement, efficiency and convenience. One of them is an electronic controlled marine diesel engine. However, we are suffered from dissemination of above engine, due to its anxiety about safety and reliability. In order to solve these problems in this study, emission characteristics test of main propulsive two-stroke diesel engine, equipped both electronic control and cam drive fuel injection systems, has been performed and evaluated under the various load conditions. From the test results, we have confirmed that exhaust gas emission characteristics of the electronic control system is similar to the cam drive system in eco-mode operation, but NOx in emission mode has been decreased 100ppm or more in full load condition. HC emission from the electronic control system is decreased 10~20ppm at 50% load, and 35~40ppm at 25% load in comparison to cam drive system. In fuel consumption, it is considered that 7g/kWh is decreased than the value of cam drive system at 700bar of injection pressure, which is 200bar higher than cam drive system.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.4
• /
• pp.307-325
• /
• 1995

IN order to gain a fundamental data for forecast or control of fish behavior and evaluated the feasibility of an application of the modeling technique to a field, in this paper a numerical model for describing the behavior of fishes in a water tank was presented. The parameters of the model were estimated by using the time-series data on the three-dimensional position of fishes and by applying the least squares algorithm. The estimated parameters were standardized to examine the variation of parameters according to the number of individuals and flow speed that the mean values of parameters were to be zero and their variances were to be one. The results obtained can be summarized as follows: (1) The standardized parameter $a^*$of propulsive force decreased according to increased the number of individuals and the flow speed. (2) The standardized parameter ${k_b}^*$ of interactive force increased according to increased the number of individuals, but decreased according to the flow speed. (3) The standardized parameter ${k_c}^*$ of schooling force increased according to │increased the number of individuals and the flow speed. (4) The standardized parameter │${k_w}^{+*}$│ of repulsive force against wall or bottom increased according to increased the number of individuals, but decreased according to the flow speed. (5) The standardized parameter │${k_w}^{-*}$│ of attractive force against wall or bottom was generally constant according to increased the number of individuals, but increased according to the flow speed. (6) The standardized parameter $\upsilon$ super(*) of damping force increased according to increased the number of individuals, but decreased according to the flow speed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.391-398
• /
• 2020

If the lost energy produced by a propeller can be partially recovered, the propulsive efficiency can be increased, and the fuel consumption reduced. The devices installed for this purpose are called Energy Saving Devices, of which the Contra-Rotating Propeller system is one of the most effective devices. The first problem to be solved to install the Contra-Rotating Propeller system on a large ship is that the mean pressure generated in the journal bearing needs to meet the design criteria of the classifications. In Korea, however, the practical use is being delayed because it cannot overcome this step. The next step is to lower local pressure to increase the reliability. In this study, to solve the mean pressure problem as the first step of practical use, a product carrier with a short stern shape was selected to reduce the weight of the shafting system, and a suitable shafting-system design plan was proposed. Shaft analysis confirmed that the mean pressure of 0.8 MPa (8 bar), which is a design criterion of the classifications for a journal bearing lining material (white metal), was satisfied. In addition, the necessity of reducing the local pressure was also confirmed.

• Journal of Advanced Navigation Technology
• /
• v.21 no.6
• /
• pp.537-543
• /
• 2017

Underwater glider is the long-term operating underwater robot that was developed with a purpose of continuous oceanographic observations and explorations. Torpedo-type underwater glider is not efficient from an aspect of maneuverability, because it uses a single buoyancy engine and motion controller for obtaining propulsive forces and moments. This paper introduces a ray-type underwater glider(RUG) with dual buoyancy engine, which improves the control performance of buoyancy and motion compared with torpedo-type underwater glider. Carrying out Computational Fluid Dynamics (CFD) analysis as static pitch drift test, the performance of fluid resistance for gliding motion was identified. Based on the calculated hydrodynamic coefficients, the dynamic simulation compared and analyzed the motion performance of torpedo-type and ray-type while controlling same volume of buoyancy engine. Small-sized model of RUG was developed to perform fundamental performance tests.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.1
• /
• pp.55-63
• /
• 2006

The purpose of this study is to prove the kinematical characteristics of Deff motion, the high bar performance, in terms of flying phases so that we can provide basic sources for improving gymnastic performance. To do this, we selected and analyzed the performance of two athletes who did Deff motion in the high bar competition of male artistic gymnastic in the 22nd Universiade 2003 Daegu. We drew the conclusions from the kinematical factors that were came out through analyzing three-dimensional cinematography of the athletes' movements, by using a high speed video camera. To make a successful performance, a performer releases the bar at a height of a high bar vertically and at a height of 82cm horizontally, and the flying performance should be made without moving forward, as maintaining the proper balance, in order to rise over 118cm high during the flying phase. When the performer is releasing the bar, an increase of the vertical speed in the center of the body and extension of a knee joint and a hip joint contribute to increasing a flying height. And when the moving body is twisted, leaning to left side is caused by the winding movement of a knee joint, which causes an unstable bar grasp. To grasp the bar stably, just before releasing the performer should gain propulsive force from twisting rotation through increasing the speed of shoulder rotation. And before the peak point, the performer should make sure of a body rotation distance over $164^{\circ}$ so that he or she can do an aerial rotary performance smoothly. When grasping the high bar, the center of the body should be above the bar and the angle of shoulder rotation should be maintained close to $540^{\circ}$ simultaneously. he high point performance(S1) has more speed on an ascending phase and less speed on a descending phase than the low point performance (S2). At the peak point, both the rotation angle of the body and that of the shoulder in high point performance are big as well. In conclusion, it is shown that a performer can make a jump toward the high bar easily with the body straight because the performer can hold the upper part of the body erect early in a descending phase.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.40-51
• /
• 1991

A Propeller design method using the newly developed blade section(KH18), which behaves better cavitation characteristics, is presented. Experimental results for two-dimensional foil sections show that the lift-drag curve and the cavitation-free bucket diagram of the new blade section are wider comparing to those of the existion NACA sections. This characteristic of the new section is particularly important for marine propeller applications since angle of attack variation of the propeller blade operating behind a non-uniform ship's wake is relatively large. A lifting surface theory is used for the design of a propeller with the developed section for a 2700 TEU container ship. Since the most suitable chordwise loading shape is not known a priori, chordwise loading shape is chosen as a design parameter. Five propellers with different chordwise loading shapes and different foil sections are designed and tested in the towing tank and cavitation tunnel at KRISO. It is observed by a series of extensive model tsets that the propeller(KP197) having the chordwise loading shape, which has less leading edge loading at the inner radii and more leading edge loading at the outer radii of 0.7 radius, has higher propulsive efficiency and better cavitation characteristics. The KP197 propeller shows 1% higher efficiency, 30% cavitation volume reduction and 9% reduction of fluctuating pressure level comparing to the propeller with an NACA section. More appreciable efficiency gain for the new blade section propeller would be expected by reduction of expanded blade area considering the better cavitation characteristics of the new blade section.

• Korean Journal of Applied Biomechanics
• /
• v.31 no.4
• /
• pp.241-248
• /
• 2021

Objective: The purpose of this study was to investigate the difference in muscle strength, kinematics, and kinetics between injured and non-injured sides of the leg after Achilles Tendon Rupture surgery during walking and running. Method: The subjects (n=11; age = 30.63 ± 5.69 yrs; height = 172.00 ± 4.47 cm; mass = 77.00 ± 11.34 kg; time lapse from surgery = 29.81 ± 10.27 months) who experienced Achilles Tendon Rupture (ATR) surgery participated in this study. The walking and running trials were collected using infrared cameras (Oqus 300, Qualisys, Sweden, 100 Hz) on instrumented treadmill (Bertec, U.S.A., 1,000 Hz) and analyzed by using QTM (Qualisys Track Manager Ver. 2.15; Qualisys, U.S.A). The measured data were processed using Visual 3D (C-motion Inc., U.S.A.). The cutoff frequencies were set as 6 Hz and 12 Hz for walking and running kinematics respectively, while 100 Hz was used for force plate data. Results: In ATR group, muscle strength there were no difference between affected and unaffected sides (p> .05). In kinematic analysis, subjects showed greater ROM of knee joint flexion-extension in affected side compared to that of unaffected side during walking while smaller ROM of ankle dorsi-plantar and peak knee flexion were observed during running (p< .05). In kinetic analysis, subjects showed lower knee extension moment (running at 2.2 m/s) and positive ankle plantar-flexion power (running at 2.2 m/s, 3.3 m/s) in affected side compared to that of unaffected side (p< .05). This lower positive ankle joint power during a propulsive phase of running is related to slower ankle joint velocity in affected side of the subjects (p< .05). Conclusion: This study aimed to investigate the functional evaluation of the individuals after Achilles tendon rupture surgery through biomechanical analysis during walking and running trials. Based on the findings, greater reduction in dynamic joint function (i.e. lower positive ankle joint power) was found in the affected side of the leg compared to the unaffected side during running while there were no meaningful differences in ankle muscle strength and walking biomechanics. Therefore, before returning to daily life and sports activities, biomechanical analysis using more dynamic movements such as running and jumping trials followed by current clinical evaluations would be helpful in preventing Achilles tendon re-rupture or secondary injury.

• The Korean Journal of Air & Space Law and Policy
• /
• v.22 no.1
• /
• pp.29-54
• /
• 2007

Nuclear Power Sources(NPS) have been used since 1961 for the purpose of generating energy for space objects and have since then been recognized as particularly suited essential to some space operations. In January 1978 a malfuctioning Soviet nuclear powered satellite, Cosmos 954, re-entered the earth's atmosphere and disintegrated, scattering radioactive debris over a wide area of the Canadian Northwest Territory. This incident provided some reasons to international legal scholars to make some principles to regulate using NPS in outer space. In 1992 General Assembly adopted "Principles Relevant to the Use of Nuclear Power Sources in Outer Space". These NPS Principles set out certain legal and regulatory requirements on the use of nuclear and radioactive power sources for non-propulsive purposes. Although these principles, called 'soft laws', are not legal norms, they have much enfluences on state practices such as 1983 DBS Principles(Principles Governing the Use by States of Artificial Earth Satellites for International Direct Television Broadcasting), 1986 RS Principles(Principles Relating to Remote Sensing of the Earth from Space) and 1996 Declaration on International Cooperation in the Exploration and Use of Outer Space for the Benefit and in the Interests of all States, Taking into Particular Account the Needs of Developing Countries. As far as 1963 Declaration of Legal Principles Governing the Activities of States in the Exploration and Use of Outer Space is concerned the main points such as free use of outer space, non-appropriation of celestial bodies, application of international law to outer space etc. have become customary international law binding all states. NPS Principles might have similar characters according to states' willingness to respect them.

• The Korean Journal of Air & Space Law and Policy
• /
• no.spc
• /
• pp.35-58
• /
• 2007

Nuclear Power Sources(NPS) have been used since 1961 for the purpose of generating energy for space objects and have since then been recognized as particularly suited essential to some space operations. In January 1978 a malfuctioning Soviet nuclear powered satellite, Cosmos 954, re-entered the earth's atmosphere and disintegrated, scattering radioactive debris over a wide area of the Canadian Northwest Territory. This incident provided some reasons to international legal scholars to make some principles to regulate using NPS in outer space. In 1992 General Assembly adopted "Principles Relevant to the Use of Nuclear Power Sources in Outer Space". These NPS Principles set out certain legal and regulatory requirements on the use of nuclear and radioactive power sources for non-propulsive purposes. Although these principles, called 'soft laws', are not legal norms, they have much enfluences on state practices such as 1983 DBS Principles(Principles Governing the Use by States of Artificial Earth Satellites for International Direct Television Broadcasting), 1986 RS Principles(Principles Relating to Remote Sensing of the Earth from Space) and 1996 Declaration on International Cooperation in the Exploration and Use of Outer Space for the Benefit and in the Interests of all States, Taking into Particular Account the Needs of Developing Countries. As far as 1963 Declaration of Legal Principles Governing the Activities of States in the Exploration and Use of Outer Space is concerned the main points such as free use of outer space, non-appropriation of celestial bodies, application of international law to outer space etc. have become customary international law binding all states. NPS Principles might have similar characters according to states' willingness to respect them.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.13 no.4
• /
• pp.233-244
• /
• 2018

The purpose of this study was to improve awareness of network marketing business in South Korea, which takes a quite negative view of network marketing, to raise awareness of "starting up a business" as independent business owners, to assist them in building their own subjecthood in network business and entrepreneurial identity, and ultimately to give some suggestions on how to improve their self-directed entrepreneurial competency and the quality of their business management. To make an empirical analysis of 121 independent business owners of Korean native network marketing, the personal and background variables of the entrepreneurs were selected as independent variables, and entrepreneurship was selected as a mediator variable. The selected dependent variables were financial and non-financial business performances. A multiple regression analysis was conducted by inputting the variables. The findings of the study were as follows: It produced an effect of more financial performance when the innovation of the independent business owners of network marketing was better, and this innovation was possible to have only when they improved in entrepreneurial efficacy and locus of control. In contrast, only authenticity had an effect on boosting non-financial business performance among the factors of entrepreneurship. To have authenticity, it's necessary to strengthen achievement needs and awareness of locus of control among the personal characteristics of the independent business owners of network marketing. Among the factors of entrepreneurship, there was better authenticity when their personal networks were broader among their background characteristics. In addition, self-efficacy that was one of personal characteristics made a direct contribution to the enhancement of non-financial performance. As a result, independent business owners of network marketing are required to hold a strong belief in their own business, to be active in business activities and to have a high efficacy as spontaneous principal agents, and they also are required to have more adventurous, planned, active and propulsive achievement needs that enable them to attain the goals of their business and keep moving forward. Besides, they should foster their locus-of-control competency that is to control, endure and be responsible for a variety of phenomena or incidents that they face, and there will be better financial performance or non-financial performance only when they demonstrate their self-belief and confidence and when they have faith in and conviction about themselves. For independent business owners of network marketing, a consumer-centered thinking that entails authenticity and trustworthiness and touches the hearts of customers is a more effective marketing strategy than an egocentric thinking as sellers when they approach customers. And they are expected to make progress in terms of the quality of business management when their business attachment or enthusiasm is great enough to match their own efficacy with entrepreneurial identity or strike a balance between them.