• Ocean Systems Engineering
• /
• v.10 no.3
• /
• pp.333-357
• /
• 2020

International Maritime Organisation (IMO) regulations insist on reduced emission of CO₂, noxious and other environmentally dangerous gases from ship, which are usually let out while burning fossil fuel for running its propulsive machinery. Contrallability of ship during sailing has a direct implication on its course keeping and changing ability, and tries to have an optimised routing. Bad coursekeeping ability of a ship may lead to frequent use of rudder and resulting changes in the ship's drift angle. Consequently, it increases vessels resistance and also may lead to longer path for its journey due to zigzag movements. These adverse effects on the ship journey obviously lead to the increase in fuel consumption and higher emission. Hence, IMO has made it mandatory to evaluate the manoeuvring qualities of a ship at the designed stage itself. In this paper a numerical horizontal planar motion mechanism is simulated in CFD environment and from the force history, the hydrodynamic derivatives appearing in the manoeuvring equation of motion of a ship are estimated. These derivatives along with propeller thrust and rudder effects are used to simulate different standard manoeuvres of the vessel and check its parameters against the IMO requirements. The present study also simulates these manoeuvres by using numerical free running model for the same ship. The results obtained from both these studies are presented and discussed here.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.3
• /
• pp.405-412
• /
• 2017

In the present study, two phase flows around a projectile vertically launched from an underwater platform have been numerically investigated by using a three dimensional multi-phase RANS flow solver based on pseudo-compressibility and a homogeneous mixture model on unstructured meshes. The relative motion between the platform and projectile was described by six degrees of freedom(6DOF) equations of motion with Euler angles and a chimera technique. The propulsive power of the projectile was modeled as the fluid force acting on the lower surface of the body by the compressed air emitted from the platform. Qualitative analysis was conducted for the time history of vapor volume fraction distributions. Uncorking pressure around the projectile and platform was analyzed to predict impact force acting on the surfaces. The results of 6DOF analysis presented similar tendency with the surficial pressure distributions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.4
• /
• pp.906-912
• /
• 2014

The study of fish robot is a main subject that are related with the propulsive force comparison using a varying amplitude and frequency for body and tail motion trajectory, and the quick turn using a proper trajectory function. In this study, when a fish robot thrusts forward, feedback control is difficult to apply for a fish robot, because body and tail joints as a sine wave are rolled. Therefore, we detect the virtual position based on the path of the fish robot, define the angle errors using the detected position and the look-ahead point on the given path, and design a controller to track given path. We have found that the proposed method is useful through the computer simulations.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.3
• /
• pp.14-21
• /
• 2006

The unsteady vortex lattice method is used to model twisting and flapping motions of a rectangular flat plate wing. The results for plunging and pitching motions were compared with the limited experimental results available and other numerical methods. They show that the method is capable of simulating many of the features of complex flapping flight. The lift, thrust and propulsive efficiency of a rectangular flat plate wing have been calculated for various twisting angles and reduced frequency with an amplitude of flapping angle($20^{\circ}$). And the effects of the twisting on the aerodynamic characteristics of the flapping wing are discussed by examination of their trends.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.3
• /
• pp.273-285
• /
• 1996

Generally, the flow around the ship's hull often appear 3-dimensional separation at the bow and stem, and the vortex by this flow affects greatly the resistance propulsive efficiency and maneuverability of the ship. This study is compared the calculated result based on the streamlines calculation method with the experimental result by oil fIlm method to analyze the patterns and characteristics of the flows around the ship's hull of chine form. DTMB Series 62, 4667-1 vessel was selected as a sample ship of chine form and model ship was painted with the mixture of oil-color, paint, and poly wax at the surface of the vessel and tested in the model towing tank of Inha University. The results obtained in this study are listed briefly as follows ; 1. For the single chine form, after $4\frac{1}{2}$ station the streamlines are crossed at the chine line and the streamlines are converted to the vortex follow the chine line. 2. For the single chine form, the vortex appered increases and severely in and arround the stern. 3. The approximate streamlines for the ship's hull of chine form can be assigned by the use of the Watanabe's basic transformation formular.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.20 no.3
• /
• pp.1-16
• /
• 1983

In this paper a discrete-vortex-method(DVM) is presented for investigating the hydromechanics of the planar hydrofoils performing the undulatory motion which can be related to fish propulsion with carangiform mode. This is an extention of the authors previous work(1981) on the 2-dimensional hydrofoil. The applicability and accuracy of the present method are shown by means of comparing the calculated lifts and moments, and their distributions over the planforms with those in available references, for aspect ratio 1.0 and 2.0 rectangular hydrofoils and a swept-back hydrofoil of aspect ratio 2.0 from reduced frequency 0.1 to 0.5. The agreement is considered good. To assure the applicability of the DVM to the study of the propulsive performance of the oscillating planar hydrofoils, the convergence tests are performed. The mean thrust(in pure heave, this is wholly due to leading-edge suction), the mean power to maintain the motion and the hydromechanical efficiency are calculated for the rectangular hydrofoil of aspect ratio 8.0 and these are compared with the calculations by Chopra & Kambe(1977) and Lan(1979) for the same cases.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.2
• /
• pp.68-74
• /
• 1995

The statistical analysis system is necessary to predict the resistance and powering performance quickly and precisely at the initial design stage. The authors propose the several functions of the performance prediction program and the structures of data bank. The program includes several series charts, regression coefficients and adapted regression analysis method based on the data bank to predict the resistance and propulsive coefficients. The calculation procedure to find out the principal dimensions and open-water efficiency of the optimum propeller is also included. The evaluation for the program and data bank is conducted by the arbitrarily selected 14 ship models. The results show good agreement with experiments within 5% mean prediction error.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.965-980
• /
• 2014

This paper presents a new estimation method of full scale propulsive performance for the pulling type podded propeller. In order to estimate the drag of pod housing, a drag velocity ratio, which includes the effects of podded propeller loading and Reynolds number, is presented and evaluated through the comparison of model test and numerical analysis. By separating the thrust of propeller blade and the drag of pod housing, extrapolation method of pod housing drag to full scale is deduced, and correction method of propeller blade thrust and torque to full scale is presented. This study utilized the drag coefficient ratio of the pod housing as a measure for expanding it to full scale, but in order to increase the accuracy of performance evaluation, additional study is necessary on the method for the full scale expansion via separating the drag of pod body, strut and fin which consist the pod housing.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.2
• /
• pp.287-301
• /
• 2013

The present paper deals with the problems of yaw angle effects on podded propulsor performance. The study aims at providing insights on characteristics of podded propulsors in azimuthing condition. In this regard, a wide numerical simulation that concerned yaw angle effect measurement on podded propeller performance was performed. The Reynolds-Averaged Navier Stokes (RANS) based solver is used in order to study the variations of hydrodynamic characteristics of podded propulsor at various angles. At first, the propeller is analyzed in open water condition in absence of pod and strut. Next flow around pod and strut are simulated without effect of propellers. Finally, the whole unit is studied in zero yaw angle and azimuthing condition. Structured and unstructured mesh techniques are used for single propeller and podded propulsor. The performance curves of the propeller obtained by numerical method are compared and verified by the experimental results. The characteristic parameters including the torque and thrust of the propeller, the axial force and side force of unit are presented as function of velocity advance ratio and yaw angle. The results shows that the propeller thrust, torque and podded unit forces in azimuthing condition depend on velocity advance ratio and yaw angle.

• Journal of Aerospace System Engineering
• /
• v.8 no.3
• /
• pp.34-40
• /
• 2014

Since the global economic crisis in year 2008, the world civil helicopter market has been growing recently. According to the market outlook in the next decade, the demand of civil helicopter will be driven by the demand of Private & Corporate, Oil & Gas, Off-shore and EMS(Emergency Medical Service) usages. On the other side, the demand of military market will be driven by the modification and upgrading for life extension or performance enhancement than the new helicopter development for replacing old models. To summarize these situations, the demand of MRO(Maintenance, Repair & Overhaul) market has also been on the rise because of the demand due to above several usages in civil side and the life-extension in military side. Through the MRO market analysis for characteristics, developmental trends and a supply chain, this paper describes that the potential of MRO business is considerably large as a propulsive power of domestic helicopter industry. And also, it proposes the construction direction of MRO network because the domestic industry must make the developmental awareness and reliability a stepping-stone towards own helicopter.