• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.502-505
• /
• 2007

In this paper we propose a novel electrode structure for high transmittance in the Patterned Vertical Alignment (PVA) LC cell. Normally, the transmittance of PVA LC cell is depended on the shape of the electrode and cell gap. We studied the area decreasing the transmittance through the electrode structure for wide viewing angle and proposed new electrode design to change LC director configuration in the area. We use the 'TechWiz LCD' for calculation of the director configuration and optical characteristics. We show the comparison of the calculated optical transmittance between the conventional PVA mode and the proposed PVA mode. From the results, we confirm that the optical transmittance of the proposed structure of the PVA cell becomes higher.

• 전기의세계
• /
• v.25 no.2
• /
• pp.87-91
• /
• 1976

Experimentally to investigate the conductive characteristic of oil-immersed paper, we observed the leakage current-voltage characteristic of oil-immersed paper, the temperature dependence of ionization rate and the effect of metal electrode on the leakage current. The results showed that the leakage current-voltage characteristic generally followed the experimental equation i=i$_{0}$ exp (K.root.E) and the slope K did not change by the temperature and electric strength, but only when the direct voltage was applied. And also the leakage current seemed to depend on the work function of metal electrode. From the above results we concluded that the deterioration of oil-immersed paper was not only caused by the thermionic emission from the cathode but also by the conductive property of oil-immersed paper in itself and the work function of metal electrode.e.

• 전기의세계
• /
• v.25 no.2
• /
• pp.100-106
• /
• 1976

A comparative study on thermal, static mechanical and dielectric characteristics were made over a temperature range of ca.20.deg.C to 320.deg.C and a frequency range of KHZ to MHZ band on low density polyethylene specimens crosslinked, respectively, by radiation and chemical method. The thermal property of both specimens shows that softening point appears to unchange by crosslinking, however, melting and liquidizing temperatures attain rapid increase at the imitiation of crosslinking. Mechanical properties show little difference to both specimens crosslinked by different method, further the behaviors were discussed in connection with the relaxation of molecular segments in amorphous phase. Dose dependent dielectric characteristics observed at ambient temperature under several fixed frequencies exhibit extremities at ca. 20 Mrad and the behaviors also were interpreted qualitatively by taking into consideration of dipole concentration change in amorphous phase together with the role of specimen geometry to the depth of oxidative layer. Observing frequency dependent dielectric characteristics, it was also proved that ionic conduction loss is appreciably greater in the specimen prepared by chemical method than that by radiation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.5
• /
• pp.450-456
• /
• 2005

In this paper, the effect of adhesion properties of semiconductive-insulating interface layer of silicone rubber on electrical properties was investigated. The modifications produced on the silicone surface by oxygen plasma were accessed using ATR-FTIR, contact angle and Surface Roughness Tester. Adhesion was obtained from T-peel tests of semiconductive layer haying different treatment durations. In addition, ac breakdown test was carried out for elucidating the change of electrical property with duration of plasma treatment. From the results, the treatment in the oxygen plasma produced a noticeable increase in surface energy, which can be mainly ascribed to the creation of O-H and C=O. It is observed that adhesion performance was determined by surface energy and roughness level of silicone surface. It is found that at dielectric strength was increased with improving the adhesion between the semiconductive and insulating interface.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.253-255
• /
• 1999

In this paper, a shape optimization algorithm of superconducting magnet using finite element method is presented. Since the superconductor loses its superconductivity over the critical magnetic field and critical current density, this material property should be taken into account in the design process. Trial and error approach of repeating the change of the design variables costs much time and it sometimes does not guarantee an optimal design. This paper presents a systematic and efficient design algorithm for the superconducting magnet. We employ the sensitivity analysis based on finite element formulation. As for optimization algorithm, the inequality constraint for the superconducting state is removed by modifying the objective function and the nonlinear equality constraint of constant volume is satisfied by the gradient projection method. This design algorithm is applied to an optimal design problem of a solenoid air-cored superconducting magnet that has a design objective of the maximum energy storage.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.161-164
• /
• 2009

This research is to show the mechanical properties of structural steels by welding at high temperature. Welding parts are divided with weld metal and HAZ(Heat Affected Zone). HAZ is formed by interval from welding heat source and heating and cooling rates. Then, the change of both microstructure and mechanical properties occurs. Discontinuity of mechanical and chemical property at HAZ is the cause of safety decrease of structure. At this point, in this research, tensile tests at high temperature with test pieces of base metal and weld metal of SS400 and SM490 are accomplished. From the results, the mechanical properties of both SS400 and SM490 are standardized without welding or non-welding.

• Korean Journal of Rural Living Science
• /
• v.6 no.1
• /
• pp.11-24
• /
• 1995

The new textile materials may be defined as textile materials different from already existing ones in the physical and chemical structure, manufacturing process, or end-use property. The present time what is called the post-industrial society is characterized by rapid change and new technology. Also, textile materials have been changed rapidly and diversely in the post-industrial society than in any other periods. The study aimed to analyze the trend of new tektite materials development in Korea and to forecast the development trend in the future. To investigate the trend of new textile materials, various written materials and informations were collected from the manufacturers, textile related periodicals, and research journals, and they were analyzed. The period of analysis was from January 1992 to May 1995. The results of this research are as followings : (1) Mixed textile materiasl such as bicomponent fiber, blended yam and blended fabric were increased. (2) High technology has an important effect upon new textile material development. (3) functional textile materials were increased (4) The high value-added products were increased. (5) The naturalized textile materials were increased.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.169-172
• /
• 2004

We fabricated MWNT-added glass fabric/epoxy composites. We observed the distribution of MWNTs in the composites using scanning electron microscopy and conformed that most of MWNTs exist in matrix rich region and interface between yams in warp and fill directions. We also investigated the change of permittivities with MWNT concentrations. Only $1wt\%$ MWNTs leads to high permittivity and electromagnetic waves are impossible to be transmitted to more than $3wt\%$ MWNT-added composites, which means the characteristics of these composites are comparable to those of metals or carbon fiber-reinforced composites.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2696-2699
• /
• 2008

Microfluidic chips have been frequently utilized to perform biochemical analysis, like cell culture, because they reduce the consumptions of analytes and reagents and automate multi-step analysis processes. It is often critical to monitor temperature in a microchannel for the analyses in order to control a reaction condition of bio or chemical molecules. We propose a novel method to monitor temperature of a microchannel flow by using polydiacetylene (PDA), a conjugated polymer, that has a unique property to transform its color from visible blue to fluorescent red by thermal stress. We inject PDA sensor droplets generated by hydrodynamic instability into a microchannel with a microheater incorporated on the channel bottom. Also, we change the channel temperature by providing the different electric power to the microheater. The results show that the florescence intensity of PDA sensor droplets linearly increases in response to the flow temperature increase within a certain range.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.07a
• /
• pp.187-189
• /
• 2008

The spatial coherence function of multy-mode beam was measured by using a Sagnac interferometer and self referencing technique. For leaner polarization laser beam passing through a multy-mode fiber, its change value of spatial mode and polarization from stress of faber and input coupling angle. And each spatial mode have each polarizations, when we simulation Wigner distribution function and Spatial Correlation function of spatial multi-mode beam by using Hermit Gaussian modes leaner sum. We measured spatial coherence function of using by multy-mode fiber. One can use this measurement method to study and characterize the property of multy-mode light field coming out of GRIN multy-mode fiber.