• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Journal of dental hygiene science
• /
• v.13 no.4
• /
• pp.386-392
• /
• 2013

The purpose of this study was to evaluate the factors related to xerostomia in patients with systemic diseases, and the results were analyzed through t-test, ANOVA, and multiple linear regression analysis. There were 62 respondents (56.9%) who reported dry mouth and the season of the most severe dry mouth was reported to be the highest during winter. According to the analysis made in the relationship of xerostomia with the awareness of general health and health behavior, the group that understood their own health poorly, had more than two kinds of diseases, and had been administered more than two kinds of daily medication showed higher xerostomia. Also, those who experienced desperation, had high dryness in other parts of the body, and heavy snoring were more aware of xerostomia (p<0.05). According to the analysis made in the relationship between xerostomia and awareness of oral health state, the group that understood their oral health poorly and had pain in the oral mucous membrane and halitosis was more aware of xerostomia (p<0.05). According to the analysis made in the relationship between quality of life and xerostomia, the group that showed high level of problem in daily living and stress and were self-conscious and felt tense due to halitosis reported more xerostomia (p<0.05). Finally, xerostomia was most correlated with consciousness of the eyes of others due to halitosis followed by the number of transferred systemic diseases and stress level. Based on such results, xerostomia was understood to be an obstacle in maintaining favorable social life and health. Since xerostomia was shown to be related to the number of transferred systemic diseases, the dental professions are asked to further improve their understanding not only on oral health but also systemic diseases. Therefore, these efforts are expected to prevent xerostomia and reduce various complications caused by xerostomia.

• Journal of Korean Society of societal Security
• /
• v.4 no.2
• /
• pp.73-78
• /
• 2011

In order to resolve the problem of change in global climate which is worsening as days go by and to preemptively cope with strengthened restriction on carbon emission, the government enacted 'Framework Act on Low Carbon Green Growth' in 2010 and selected green technology and green industry as new national growth engines. For this reason, the necessity to use the un-utilized waste heat across the whole industrial system has become an issue, and studies on and applications of recycling in the agricultural and fishery fields such as cultivation of tropical crops and flatfishes by utilizing the waste heat and thermal effluent generated by large industrial complexes including power plants are being actively carried out. In this study, we looked into the domestic and overseas examples of having utilized waste heat abandoned in the form of power plant thermal effluent, and carried out economic efficiency evaluation of sturgeon aquaculture utilizing thermal effluent of Yeongwol LNG Combined Cycle Power Plant in Gangwon-do. In this analysis, we analyzed the economic efficiency of a model business plan divided into three steps, starting from a small scale in order to minimize the investment risk and financial burden, which is then gradually expanded. The business operation period was assumed to be 10 years (2012~2021), and the NVP (Net Present Value) and economic efficiency (B/C) for the operation period (10 years) were estimated for different loan size by dividing the size of external loan by stage into 80% and 40% based on the basic statistics secured through a site survey. Through the result of analysis, we can see that reducing the size of the external loan is an important factor in securing greater economic efficiency as, while the B/C is 1.79 in the case the external loan is 80% of the total investment, it is presumed to be improved to 1.81 when the loan is 40%. As the findings of this study showed that the economic efficiency of sturgeon aquaculture utilizing thermal effluent of power plant can be secured, it is presumed that regional development project items with high added value can be derived though this, and, in addition, this study will greatly contribute to reinforcement of the capability of local governments to cope with climate change.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.33 no.3
• /
• pp.1-15
• /
• 2015

Based on the analysis and interpretation of the headwords and poetic words of a group of eleven collecting sceneries of Jeonju, the origin and transformations of the Jeonju-Palkyung(Eight sceneries of Jeonju) investigated by a time-series analysis are as follows. As there is no collection of landscape with a formal structure similar to that of the current Jeonju-Palkyung, prior to the Palkyung by Chujae(秋齋) Cho Soo-Sam(趙秀三, 1762~1849), there is no significant problem in assuming the eight poems in Chujaejib(秋齋集) are the origins of the Jeonju-Palkyung, and it is estimated to have been produced in 1829. In the late-19th century poem 'Wansanseunggyeong(完山勝景)', 'the Palkyung in Yeollyeo Chunhyang Sujeolga', and 'the Palkyung delivered by poet Shin Seokjeong in the Japanese colonial era', only the 'Dongpogwibeom(東浦歸帆)' changed from Dongjipo to Dongchon of Bongdong as for 'Landscape Setting There($L_{ST}$)' according to changes in district administration; despite this change, the fact that they are not too different from the Palkyung of Cho Soo-Sam, also supports this. Moreover, according to the headword concordance analysis, it is proven that the Jeonju-Palkyung was established in the late-19th century and continued to be the region's representative sceneries even during the Japanese colonial era, and later 'Namcheonpyomo(南川漂母)' and 'Gonjimangwol(坤止望月)' were added to expand to the Jeonju-Sipkyung(ten sceneries of Jeonju). But when we see there are famous spots that are the origins of the Jeonju-Sipkyung, including Gyeonggijeon, Geonjisan, Jogyeongdan, Omokdae, and Girinbong, Deokjinyeon, and Mangyeongdae, all of which have great representational significance as the capital of Jeolla Provincial Office as well as of the place of origin for Joseon Dynasty in the grouping of sceneries during the early Joseon Dynasty, including "Paehyangsipyeong (沛鄕十詠)", "Gyeondosipyeong (甄都十詠)", and "Binilheonsipyeong(賓日軒十詠)", the beginnings of the semantic Jeonju-Palkyung should be considered up to the first half of Joseon Dynasty. During this period, not only the fine sceneries with high retrospective merit as the capital of Hubaekje, like Gyeonhwondo(甄萱都), but also the sceneries like Mangyeongdae that reminds people of Jeong Mongju(鄭夢周) and Yi Seonggye(李成桂) in the late period of Goryeo appeared, elevating the status of Jeonju as the capital of Hubaekje and shortening the historical gaps as the place of origin of the Joseon Dynasty. The Jeonju-Palkyung is an organic item that carries the history of the Joseon Dynasty after Hubaekje and has gone through many cycles of disappearing and reappearing, but it has continued to change and transform as the region's representative sceneries. The Jeonju-Palkyung is a cultural genealogy that helps one understand the 'Jeonju Hanpunggyeong(韓風景: the sceneries of Korea in Jeonju)', and the efforts to preserve and pass it down to the next generation would be the responsibility of the people of Jeonju.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.2
• /
• pp.158-175
• /
• 2005

Statement of problem. Every effort has been continually made to obtain objectivity in measuring the longevity of fixed restorations, such as by establishing unified judgement standard for deciding success and adopting statistical method that analyzes the data of successful and failed cases at the same time. In Korea, however desired level of development has not to be made in this field yet. Purpose. This study, adopting California Dental Association (CDA) quality evaluation system, established objective standard for deciding success, and inferred the longevity of fixed restorations and their failure analysis through adopting Kaplan-Meier survival analysis. Material and method. In order to assess the longevity of flxed restorations serviced in Korea and causes of failure, a total of 1109 individuals (aged 15-74, 716 women and 393 men loaded with 2551 unit fixed restorations, and 1934 abutments) who lived in Kyung-In Province were examined and the findings were as follows : Results. 1. Length of service of fixed restorations serviced in Korea was 6.86$\pm$0.15 yr (mean), 5.5 yr (median), and the rate of success was 65.82% in 5 year survival, and 21.15% in 10 year survival. 2. When there was patient's need for replacing old prosthetics, longevity of fixed restorations was 7.51$\pm$0.27 yr (mean), 7 yr (median), and the rate of success was 61.08% in 5 year survival, and 17.57% in 10 year survival. 3. Longevity of fixed restorations was longest in the over-sixty age group(9.21$\pm$0.66) and that of the teen age group(3.39$\pm$0.28) was shortest (p<0.05). 4. Longevity of fixed restorations of women (7.38$\pm$0.18 years) was longer than that of men (6.00$\pm$0.26) (p<0.05). 5. As for the provider factor (such as unlicensed performers, university hospitals, and private clinic), there was no statistically significant difference in longevity of fixed restorations. 6. Defective margin (34.78%). periodontal disease (12.15%), periapical involvement (11.73%), was the most frequent causes of failure and poor esthetics group showed the longest life above all (p<0.05). Actual frequent causes of failure after removing old prosthetics were defective margin, periapical involvement, periodontal disease and uncemented restoration. In 75.67% of the cases, abutment state after removing old prosthetics was good enough for loading another prosthetics. 7. There was found to have statistically significant influence between longevity of single crown (6.35$\pm$0.20 yr) and that of 3 unit fixed restorations (7.60$\pm$0.30 y) (p<0.05). In each case the most frequent cause of failure was defective margin. 8. The number of cantilever pontic, pontic/abutment ratio, oral hygiene status were found to have no statistically significant influence on longevity of fixed restorations in all groups (p>0.05). 9. Longevity of fixed restorations made of non precious metal was longest (9.60$\pm$0.40 yr) semi precious and precious trailing behind(p<0.05). 10. Group function group (37.04%) and partial group function group (44.62%) were predominant in frequency but showed no correlation between them and among different types of occlusal plane and different types of occlusal surface (p>0.05). 11. Longevity of fixed restorations was longest in the centric interference group(9.35$\pm$0.62) (p<0.05) among different types of occlusal interference. Conclusion. We found that longevity of fixed restorations serviced in Korea is affected by age, gender and type of material, and that most frequent cause of failure is defective margin. In order to assess the accurate longevity of axed restorations, unified research design. overcoming inter-observer difference and establishing the objective research items are needed. Furthermore, it is thought that prospective approach through thorough study and regular follow-ups is needed just from the start of research. Nationwide detailed studies on length of service of fixed restorations manufactured in Korea are hoped to be conducted hereafter.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.4
• /
• pp.424-434
• /
• 2009

Statement of problem: Problems such as loosening and fractures of retained screws and fracture of implant fixture have been frequently reported in implant prosthesis. Purpose: Implant has weak mechanical properties against lateral loading compared to vertical occlusal loading, and therefore, stress analysis of implant fixture depending on its material and geometric features is needed. Material and methods: Total 28 of external hexed implants were divided into 7 of 4 groups; Group A (3i, FULL $OSSEOTITE^{(R)}$Implant), Group B (Nobelbiocare, $Br{\aa}nemark$ $System^{(R)}$Mk III Groovy RP), Group C (Neobiotec, $SinusQuick^{TM}$ EB), Group D (Osstem, US-II). The type III gold alloy prostheses were fabricated using adequate UCLA gold abutments. Fixture, abutment screw, and abutment were connected and cross-sectioned vertically. Hardness test was conducted using MXT-$\alpha$. For fatigue fracture test, with MTS 810, the specimens were loaded to the extent of 60-600 N until fracture occurred. The fracture pattern of abutment screw and fixture was observed under scanning electron microscope. A comparative study of stress distribution and fracture area of abutment screw and fixture was carried out through finite element analysis Results: 1. In Vicker's hardness test of abutment screw, the highest value was measured in group A and lowest value was measured in group D. 2. In all implant groups, implant fixture fractures occurred mainly at the 3-4th fixture thread valley where tensile stress was concentrated. When the fatigue life was compared, significant difference was found between the group A, B, C and D (P<.05). 3. The fracture patterns of group B and group D showed complex failure type, a fracture behavior including transverse and longitudinal failure patterns in both fixture and abutment screw. In Group A and C, however, the transverse failure of fixture was only observed. 4. The finite element analysis infers that a fatigue crack started at the fixture surface. Conclusion: The maximum tensile stress was found in the implant fixture at the level of cortical bone. The fatigue fracture occurred when the dead space of implant fixture coincides with jig surface where the maximum tensile stress was generated. To increase implant durability, prevention of surrounding bone resorption is important. However, if the bone resorption progresses to the level of dead space, the frequency of implant fracture would increase. Thus, proper management is needed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.4
• /
• pp.445-456
• /
• 2009

Statement of problem: Many studies have been conducted to improve the primary stability of implants by providing bioactive surfaces via surface treatments. Increase of surface roughness may increase osteoblast activity and promote stronger bonding between bone and implant surface and it has been reported that bioactive surface or titanium can be obtained through alkali and heat treatment. Purpose: The purpose of this study was to evaluate the stability of alkali and heat treated implants via histomorphometric analysis. Material and methods: Specimens were divided into three groups; group 1 was the control group with machined surface, the other groups were treated for 24 hours in 5 M NaOH solution and heat treated for 1 hour at $600^{\circ}C$ in the atmosphere (group 2) and vacuum (group 3) conditions respectively. Surface characteristics were analyzed and fixtures were implanted into rabbits. The specimens were histologically and histomorphometrically compared according to healing periods and change in bone composition were analyzed with EPMA (Electron Probe Micro Analyzer). Results: 1. Groups treated with alkali and heat showed increase of oxidization layer and Na ions. Groups 2 which was heat treated in atmosphere showed significant increase of surface roughness (P<.05). 2. Histomorphometric analysis showed significant increase in BIC (bone to implant contact) according to increase in healing period and there was significant increases in groups 2 and 3 (P<.05). 3. BA(bone area) ratio showed similar results as contact ratio, but according to statistical analysis there was significant increase according to increase in healing period in group 2 only (P<.05). 4. EPMA analysis revealed no difference in gradation of bone composition of K, P, Ca, Ti in surrounding bone of implants according to healing periods but groups 2 and 3 showed increase of Ca and P in the initial stages. Conclusion: From the results above, it can be considered that alkali and heat treated implants in the atmosphere have advantages in osseointegration in early stages and may decrease the time interval between implantation and functional adaptation.

• Spatial Information Research
• /
• v.22 no.3
• /
• pp.23-24
• /
• 2014

NGII (National Geographic Information Institute) has been providing VRS (Virtual Reference Station) service so that could determine precise positioning in real time since 2007. However, since the VRS service has to maintain the connected status with VRS server, the number of users who can use VRS service are limited by capacity of VRS server. To solve this problem, NGII has been providing FKP (Virtual Reference Station) service using one way telecommunication from November 1, 2012. Therefore, it is predicted that the usage of FKP service will increase in public surveying and cadastral resurveying in the future. However, the studies with respect to analysis of FKP precision for applying to public surveying and cadastral resurveying is not conducted enough. In this study, to analyse the application possibility of FKP on the public surveying and cadastral resurveying, the two kind analysis were performed. First is the analysis of accuracy according to the configuration of reference station of FKP and VRS. One is consisted of same reference stations, another is consisted of different reference stations. Second is the accuracy anlalysis of horizontal and vertical positioning acquiring VRS and FKP data in various measurement environment based on VRS regulation. Result of first study, Positioning accuracy according to the configuration of the reference stations satisfies related regulation. However, accuracy of FKP in case of different reference stations is worse than in case of same reference stations.. The result of second test shows that the horizontal precision of FKP and VRS in good measurement environment satisfy the allowed precision. However, in some case, horizontal precision of FKP and VRS in poor measurement environment exceed the allowed precision. In addition, the number of exceeding the allowed precision in the FKP is more than the VRS. The vertical precision of the VRS satisfy related work provision. In conclusion, the result of this study shows that the FKP only in open area should be used for public survey and cadastral resurvey. Therefore the additional studies with respect to the improvement of FKP precision should be conducted.

• Journal of Korea Technology Innovation Society
• /
• v.20 no.4
• /
• pp.1089-1121
• /
• 2017

'Technological convergence' is the recent innovation trend which facilitates to solve social crux as well as to generate new industries. Korean government research institutes (GRIs) have taken a pivotal role for economic growth which capitalized on technology-oriented strategies. Recently, the policy interests on the transition of their role and mission towards multidisciplinary research organization is increasingly shed lights. This study regards the collaborative activities as one of the key success factors in the multidisciplinary research. In this sense, this study sets research purposes as follows: First, we intend to define a concept and to confine a scope of multidisciplinary research from the view point of R&D purposes and problem-solving process. Second, we categorize the collaboration and the relevant performances which reflect the characteristics of the multidisciplinary research. Third, we analyze the characteristics of collaborative activities and the effects of strength on the research performances. To this end, this study conducted a survey of 104 research project directors, which have experienced at least one of two types of multidisciplinary research projects through National R&D project or NST (National Research Council of Science & Technology) convergence research project. Then, we conducted regression analysis by utilizing the survey results in order to verify the relation between the collaborative activities and the performances. As results of analyses, first, the diversification of collaboration partners was a salient factor in the process of knowledge creation. Second, collective works among the researchers in similar area and domain enhanced mission-oriented technology development projects such as patent creation or technology transfer. Third, we verified that the diversity of created knowledge and the degree of relation continuity between researchers increased in the condition of guaranteeing individual researcher's independence and autonomy as well as sharing various technological capabilities. These results provide the future policy directions related to the methods to measure the collaboration and performance analysis for multidisciplinary research.

• Korean Journal of Family Social Work
• /
• no.54
• /
• pp.297-331
• /
• 2016

The purpose of this study was to examine the mediating roles of neglectful rearing attitudes and mental health in the relationship between economic status of single-parent famillies and school adjustment, and the differences between single-parent and two-parent families, using structural equation modeling. Data were obtained from the Middle School 1 Panel(third-wave) of the Korean Child and Youth Panel Survey 2010. This study selected 2,195 middle school 3th-grade students (249 from single-parent families and 1,946 from two-parent families). Data were examined with structural equation modeling and multi-group analysis using AMOS 21.0, and mediating effects were tested using the Sobel test. The results were as follows; First, the single-parent children reported lower levels of economic status and school adjustment, and higher levels of neglectful rearing attitudes than the two-parent children. Second, multi-group analysis showed a statistically significant difference between single-parent and two-parent in structural equation modeling. Economic status of two-parent famillies affected school adjustment of children, but economic status of single-parent famillies did not affect school adjustment of children. Third, as a result of examining for total effect, the variable that most influenced school adjustment of children was neglectful rearing attitudes. Fourth, neglectful rearing attitudes and mental health did play a mediating role in the relationship between economic status and school adjustment in case of two-parent famillies, but neglectful rearing attitudes and mental health did not play a mediating role in case of single-parent famillies. Based on the result, this study stressed the following; First, the study suggested that problem of the single-parent famillies supporting standard which is concentrated on the low income single-parent famillies. Second, the study proposed multifaceted support measures which reflects characteristics of single-parent famillies to increase school adjustment of the single-parent children.