• Bulletin of the Korean Chemical Society
• /
• v.30 no.10
• /
• pp.2362-2364
• /
• 2009

We report Pt hexapod nanoparticles with $6.4\;{\sim}\;9.7$ nm in size by a polyol process in the presence of PVP as a stabilizer and additive as a kinetic controller. The structure and morphology of Pt nanostructures are confirmed by field-emission transmission electron microscopy. The morphological control over platinum nanoparticles is achieved by varying the amount of seeds in the polyol process, where platinum precursor is reduced by ethylene glycol to form Pt nanoparticle at $150\;{^{\circ}C}$. As volume ratio between precursor-solution and seed-solution is increased from 10 to 50, the shape of Pt nanostructures is evolved from small seeds to tripod and hexapod. In addition, the size-controlled platinum hexapod nanostructures are successfully obtained using seeding method.

• Journal of the Korean Ceramic Society
• /
• v.32 no.5
• /
• pp.543-548
• /
• 1995

Li-ferrite powders were prepared from mixture of Fe and Li salts using a hydrothermal method. Their crystal structure, microstructure and magnetic property were investigated with X-ray diffraction analysis, chemical analysis, SEM, and VSM. In the case of using FeCl3 as a precursor, Li-ferrite powders were synthesized. However, Fe3O4 was formed when the precursor was a divalented Fe2SO4 or FeCl2. The precipitation rate of Li-ferrite was increased as the reaction temperature increased. The optimum conditions of synthesis were the mole ratio of Fe+++/Li+=2, pH 13, the reaction temperature of 25$0^{\circ}C$ and the reaction time of 120min. With this condition, the spherical particles with good dispersion were obtained with average particle size of 0.4${\mu}{\textrm}{m}$ and saturation magnetization of 65 emu/g.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.107-108
• /
• 2006

High $J_c$ $YBa_2Cu_3O_x$, superconducting films were fabricated by MOD method using fluorine-free dichloroacetic acid(DCA) as chelating solvent for preparing precursor solution. DCA-MOD precursor solution was coated on a single crystal (001) $LaAlO_3$(LAO) substrate by a dip coating method with a speed of 25 mm/min. Coated films were calcined at lower temperature up to $500^{\circ}C$ and Conversion heat treatment was performed at various temperatures of $780{\sim}810^{\circ}C$. SEM observations showed that films have very dense microstructures for the films prepared at the temperature higher than $800^{\circ}C$ regardless of diluting solvent; methanol or 2-methoxyethanol. A High critical current density ($J_c$) of 1.28 $MA/cm^2$ (@77 K and self-field) was obtained for the YBCO film prepared using 2-methoxyethanol as a solvent.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.3
• /
• pp.13-17
• /
• 2006

The effect of the addition of the nano size $Y_2O_3$ powder on the microstructurte and superconducting properties of YBCO thin film deposited on LAO single crystalline substrate by TFA-MOD method was studied. Nano size $Y_2O_3$ powder was added to the stoichiometric precursor solution with a cation ratio of Y : Ba . Cu = 1 : 2 : 3 prepared using TFA as chelating agent. Precursor solutions with and without $Y_2O_3$ addition were coated on $LaAlO_3(100)$ single crystalline substrates by dip coating method. Calcination and conversion heat treatments were performed in controlled atmosphere containing moisture Current carrying capacity(Jc) of YBCO film was enhanced about 50% by $Y_2O_3$ doping and it is thought to be due to the better connectivity of YBCO grains and/or the flux pinning by the $Y_2O_3$ particles embedded in YBCO grains.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.789-794
• /
• 2002

In this study, nano-sized Si-C-N precursor powders were synthesized by Chemical Vapor Condensation Method(CVC) using TMS(Tetramethylsilane: $Si(CH_3)_4$), $NH_3$ and $H_2$ gases under the various reaction conditions of the reaction temperature, TMS/$NH_3$ ratio and TMS/$H_2$ ratio. XRD and FESEM were used to analysis the crystalline phase and the average particle size of the synthesized powders. It was found that the obtained powders under the considering conditions were all spherical amorphous powder with the particle size of 87∼130 nm. The particle size was decreased as the reaction temperature increased and TMS/$NH_3$ and TMS/$H_2$ ratio decreased. As the results of EA analysis, it was found that the synthesized powders had been formed the powders composed of Si, N, C and H. Through FT-IR results, it was found that the synthesized powders were Si-C-N precursor powders with Si-C, Si-N and C-N bonds.

• Korean Journal of Materials Research
• /
• v.20 no.5
• /
• pp.262-266
• /
• 2010

ZnO nanostructures were grown on an Au seed layer by a hydrothermal method. The Au seed layer was deposited by ion sputter on a Si (100) substrate, and then the ZnO nanostructures were grown with different precursor concentrations ranging from 0.01 M to 0.3M at $150^{\circ}C$ and different growth temperatures ranging from $100^{\circ}C$ to $250^{\circ}C$ with 0.3 M of precursor concentration. FE-SEM (field-emission scanning electron microscopy), XRD (X-ray diffraction), and PL (photoluminescence) were carried out to investigate the structural and optical properties of the ZnO nanostructures. The different morphologies are shown with different growth conditions by FE-SEM images. The density of the ZnO nanostructures changed significantly as the growth conditions changed. The density increased as the precursor concentration increased. The ZnO nanostructures are barely grown at $100^{\circ}C$ and the ZnO nanostructure grown at $150^{\circ}C$ has the highest density. The XRD pattern shows the ZnO (100), ZnO (002), ZnO (101) peaks, which indicated the ZnO structure has a wurtzite structure. The higher intensity and lower FWHM (full width at half maximum) of the ZnO peaks were observed at a growth temperature of $150^{\circ}C$, which indicated higher crystal quality. A near band edge emission (NBE) and a deep level emission (DLE) were observed at the PL spectra and the intensity of the DLE increased as the density of the ZnO nanostructures increased.

• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.127-132
• /
• 2011

Many research groups have been manufacturing coated conductor by various processes such as PLD, MOD, and MOCVD, but the methods with production cost suitable for wide and massive application of coated conductor did not develop yet. Spray pyrolysis method adopting ultrasonic atomization was tried as one of the possible option. GdBCO precursor films have been deposited on IBAD substrate by spray pyrolysis method at low temperature and converted to GdBCO by post heat treatment. Ultrasonic atomization was used to generate fine droplets from precursor solution of Gd, Ba, and Cu nitrate dissolved in water. Primary GdBCO films were deposited at $500^{\circ}C$ and oxygen partial pressure of 1 torr. After that, the films were converted at various temperatures and low oxygen partial pressures. C-Axis oriented films were obtained IBAD substrates at conversion temperature of around $870^{\circ}C$ and oxygen partial pressures of 500 mtorr ~ 1 torr in a vacuum. Thick c-axis epitaxial film with the thickness of 0.4 ~ 0.5 ${\mu}m$ was obtained on IBAD substrate. C-axis epitaxial GdBCO films were successfully prepared by ex-situ methods using nitrate precursors on IBAD metal substrate. Converted GdBCO films have very dense microstructures with good grain connectivity. EDS composition analysis of the film showed a number of Cu-rich phase in surface. The precursor solution having high copper concent with the composition of Gd : Ba : Cu = 1 : 2 : 4 showed the better grain connectivity and electrical conductivity.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.3
• /
• pp.393-401
• /
• 2012

Inorganic pigment is excellent at stability to human body and compatibility with different materials and has been used in a variety of field such as cosmetics, printing inks, paints, and construction materials for improving the aesthetic features. In this paper, hydrothermal synthesis method was used to prepare the manganese and iron dopped with titania pigment. As process parameters, the amount of manganese precursor and iron precursor, and calcined temperature was changed. Optimum amounts of manganese and iron dopped with titania precursor to give excellent color index was manganese 1.0wt% and iron 1.5wt% for dopped titania, and Optimum calcination temperature was $550^{\circ}C$. The synthesized pigments were analyzed by XRD, SEM, EDS, Spectrophotometer and UV-Vis Spectrometer.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.6
• /
• pp.86-91
• /
• 2010

Superconductor material $Bi_2Sr_2Ca_2Cu_3O_x$(Bi-2223) powders were synthesized by ultrasonic spray pyrolysis method. It is clear that Bi-2223 phase more than Bi-2212 phase was acquired at sufficient synthesized time. Best condition for Bi-2223 phase was synthesizing temperature at $860^{\circ}C$. We also investigated the effects for concentrations and viscosities of starting liquid precursor as well as temperature distribution of reacting furnace. The size of synthesized powder was decreased by decreasing the concentration of starting liquid precursor. Modified reacting furnace with four different temperature heating zones gave us successful results for desirable nano-powder including $Bi_2Sr_2Ca_2Cu_3O_x$ phase. Citric acid addition to starting liquid precursor showed increasing of the size for synthesized powder. Bi-2223 single phase was acquired from Bi2223 and Bi-2212 mixed phases through heat treatment in box furnace at 24 hours.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.4
• /
• pp.198-203
• /
• 2014

ZnO nanorods have been deposited on ITO glass by electrodeposition method. The optimization of two process parameters (precursor concentration and current) has been studied in order to control the orientation, morphology, and optical property of the ZnO nanorods. The structural and optical properties of ZnO nanorods were systematically investigated by using field-emission scanning electron microscopy, X-ray diffractometer, and photoluminescence. Commonly, the results show that ZnO nanorods with a hexagonal form and wurtzite crystal structure have a c-axis orientation and higher intensity for the ZnO (002) diffraction peaks. Both high precursor concentration and high electrodeposition current cause the increase in nanorods diameter and coverage ratio. ZnO nanorods show a strong UV (3.28 eV) and a weak visible (1.9 ~ 2.4 eV) bands.