• Korean Journal of Materials Research
• /
• v.22 no.3
• /
• pp.118-122
• /
• 2012

We synthesized porous $Co_3O_4/RuO_2$ composite using the soft template method. Cetyl trimethyl ammonium bromide (CTAB) was used to make micell as a cation surfactant. The precipitation of cobalt ion and ruthenium ion for making porosity in particles was induced by $OH^-$ ion. The porous $Co_3O_4/RuO_2$ composite was completely synthesiszed after anealing until $250^{\circ}C$ at $3^{\circ}C$/min. From the XRD ananysis, we were able to determine that the porous $Co_3O_4$/RuO2 composite was comprised of nanoparticles with low crystallinity. The shape or structure of the porous $Co_3O_4/RuO_2$ composite was studied by FE-SEM and FE-TEM. The size of the porous $Co_3O_4/RuO_2$ composite was 20~40 nm. From the FE-TEM, we were able to determine that porous cavities were formed in the composite particles. The electrochemical performance of the porous $Co_3O_4/RuO_2$ composite was measured by CV and charge-discharge methods. The specific capacitances, determined through cyclic voltammetry (CV) measurement, were ~51, ~47, ~42, and ~33 F/g at 5, 10, 20, and 50 mV/sec scan rates, respectively. The specific capacitance through charge-discharge measurement was ~63 F/g in the range of 0.0~1.0 V cutoff voltage and 50 mAh/g current density.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.9
• /
• pp.61-69
• /
• 2017

This study presents the experimental results of $CaCO_3$ formation in sand by the Enzyme Induced Carbonate Precipitation (EICP) method. Concentration of $CaCO_3$ with elapsed reaction time is calibrated by standardized procedure by measuring $CO_2$ pressure, and it increases with time towards asymptotic value. Jumunjin sand saturated with EICP solution shows that both shear wave velocity and electrical conductivity sharply increase as the reaction starts to approach to the constant values after 50 hours of reaction time. Urease concentration of 0.5 g/L exhibits 224% higher final shear wave velocity than that of 0.1 g/L. The nucleation models hint that carbonate tends to precipitate not only at grain contacts but also at grain surfaces. Regardless of urease concentration, electrical conductivity and shear wave velocity follow the unique path. The scanning electron microscopic images and X-ray computed tomographic images validate the spatial configuration of produced $CaCO_3$ in soils.

• International Journal of Advanced Culture Technology
• /
• v.8 no.2
• /
• pp.283-288
• /
• 2020

This study investigated the purification process of groundwater contaminated with zinc and arsenic using a permeable reactive barrier with a zero-valent iron/pumice mixture. We determined the removal rates of the contaminants for 30 days. In this study, column reactor filled with the zero-valent iron/pumice reactive mixture was used. Experimental results showed that the mixture exhibited an almost complete removal of the zinc and arsenic ions. Arsenic was removed via co-precipitation and adsorption processes while zinc ions were asorbed in active sites.The purification process of water from the metal ionscontinued for 30 days with constant hydraulic conductivity because of the enhanced porosity of the pumice and interparticle distance between the zero-valent iron and pumice. Contaminants removal rates and the remediation mechanism for each reactive system are described in this paper.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.2
• /
• pp.103-110
• /
• 2019

Cu-Zn-Al catalysts were prepared via co-precipitation method for low-temperature water-gas shift (LT-WGS) reaction under practical reaction condition. Aging time was systematically changed to find optimum point for LT-WGS under practical condition. The Cu-Zn-Al catalyst aged for 72 hours showed the highest CO conversion within low-temperature range as well as very stable catalytic activity for 200 hours despite the practical reaction condition.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.30 no.2
• /
• pp.173-180
• /
• 2004

Nano sized ZnO particle as 20-30nm applies for material, pigments, rubber additives, gas sensors, varistors, fluorescent substance as well as new material such as photo-catalyst, sensitizer, fluorescent material. ZnO with a particle size in the range 20-30nm has provided to be an excellent UV blocking material in the cosmetics industry, which can be used in sunscreen product to enhance the sun protection factor and natural makeup effect. But pure ZnO particles application limits for getting worse wearing feeling. We make high-functional inorganic-composite that coated with nano-ZnO on the plate-type particle such as sericite, boron nitride and bismuthoxychloride. In this experiment, we synthesized composite powder using hydrothermal precipitation method. The starting material was ZnCl$_2$ Precipitation materials were used hexamethylenetetramine(HMT) and urea. We make an experiment with changing as synthesis factors that are concentrations of starting material, precipitation materials, nuclear formation material, reaction time, and reaction temperature. We analyzed composite powder's shape, crystallization and UV-blocking ability with FE-SEM, XRD, FT-IR, TGA-DTA, In vitro SPF test. The user test was conducted by product's formulator. In the results of this study, nanometer sized ZnD was coated regardless of the type of plate-powder at fixed condition range. When the coated plate-powders were applied in pressed powder product, the glaze of powder itself decreased, but natural make-up effect, spreadability, and adhesionability were increased.

• Applied Chemistry for Engineering
• /
• v.33 no.5
• /
• pp.466-470
• /
• 2022

The catalytic thermal oxidizer process has recently attracted considerable attention for the oxidation and decomposition of volatile organic compounds at low temperatures (< 450 ℃) with high efficiency (> 95%). Although many noble metal catalytic materials are well established, they are expensive and hazardous. Herein, highly active and low-cost Cu-Mn bimetallic catalysts were prepared using a simple and facile synthesis method involving the co-precipitation of Cu and Mn precursors. The synthesis of the catalyst was optimized by controlling the composition ratio of Cu and Mn. The optimized catalyst exhibited a large surface area of 230.8 m²/g with a mesoporous structure. To demonstrate the catalytic performance, the Cu-Mn catalyst was tested for the oxidation reaction of ethyl acetate, showing a high conversion efficiency of 100% at a low temperature of 250 ℃.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.2
• /
• pp.95-102
• /
• 2019

In order to investigate the effect of water treatment on activity of WGS catalyst, $Cu/ZnO/MgO/Al_2O_3$ (CZMA) catalysts were synthesized by co-precipitation method. The prepared catalysts were water-treated at two different temperature (250, $350^{\circ}C$). Synthesized catalysts were characterized by using BET, SEM, $N_2O$ chemisorption, XRD, $H_2-TPR$ and XPS analysis. The catalytic activity tests were carried out at a GHSV of $28,000h^{-1}$ and a temperature range of $180-320^{\circ}C$. The reduction temperature decreased with water treatment and CZMA_250 catalyst showed the lowest reduction temperature and retained a large amount of $Cu^+$. Water-treated catalysts showed increased reactivity compared to untreated catalyst and the CZMA_250 catalyst showed higher catalytic activity on WGS reaction.

• Clean Technology
• /
• v.21 no.1
• /
• pp.68-75
• /
• 2015

In this study, we investigated the structure and properties of a highly heat conductive metal-ceramic core-shell CoAl₂O₄@Al micro-composite for heterogeneous catalysts support. The CoAl₂O₄@Al was prepared by hydrothermal surface oxidation of Al metal powder, which resulted in the structure with a high heat conductive Al metal core encapsulated by a high surface area CoAl₂O₄ shell. For comparison, CoAl₂O₄ was also prepared by co-precipitation method and also utilized for a catalyst support. Rh catalysts supported on CoAl₂O₄@Al and CoAl₂O₄ were prepared by incipient wetness impregnation and characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), CO chemisorption, and temperature-programmed reduction (TPR). The properties of catalysts were investigated for glycerol steam reforming reaction for hydrogen production at 550 ℃. Rh/CoAl₂O₄@Al exhibited about 2.8 times higher glycerol conversion turnover frequency (TOF) than Rh/CoAl₂O₄ due to facilitated heat transport through the core-shell structure. The CoAl₂O₄@Al and CoAl₂O₄ also showed some catalytic activities due to a partial reduction of Co on the support, and a higher catalytic activity was also found on the CoAl₂O₄@Al core-shell than CoAl₂O₄. These catalysts, however, displayed deactivation on the reaction stream due to carbon deposition on the catalysts surface.

• Korean Journal of Microbiology
• /
• v.9 no.4
• /
• pp.175-178
• /
• 1971

Because of the cases of Japanese Encephalitis(J.E.) were reported every year in Korea. We, Dong-A Pharmaceutical Co., Ltd., produced J.E. virus vaccine, with lower price, since 1970 in order to prevent ourselves from being infected by the disease. And inoculated the J.E. virus vaccine for the children with a great success. We are going to report several questions which brought about in producing the J.E. virus vaccine by alcohol precipitation, protamine sulfate treatment method. The results obtained were as folows ; 1) In process treated with 40% alcohol, we used to ethanol made in Germany, but it was too expensive to use it. As the result which we had studied about it, we were satisfied with J.E. virus vaccine which produced with alcohol made in Korea, and then, we treated with accurate specific gravity of 40% ethanol for the precipitation of the virus. And also, we knew that it was the best method to be treated it for 3hrs, $13^{\circ}C$. 2) When we treated with protamine sulfate (0.025mg/ml), we acquired the highest potent titer, and suited into purpose for the nitrogen concentration. 3) The filtration of the purified J.E. virus vaccine, in case of millipore filter paper of large pore size was not suitable for the sterility. Therefore the pore size less than 0.8.$\mu$ (AA filter paper) in millipore filter paper was very suitable. But it seemed to be important subhects that the smaller was the pore size, the lower was the potent titer.

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.649-656
• /
• 2002

In situ patterned zinc oxide thin films were prepared by precipitation of Zn(NO$_3$)$_2$ aqueous solution containing urea and by microcontact printing using Self-Assembled Monolayers(SAMs) on A1/SiO$_2$/Si substrates. The visible precipitation of Zn(OH)$_2$ that was formed in the Zn(NO$_3$)$_2$ aqueous solution containing urea was enhanced with an increase of the reaction temperature and the amount of urea. As the reaction time of Zn(NO$_3$)$_2$ with urea was prolonged, the thickness and grain size of Zn(OH)$_2$ thin layers were increased, respectively. The optimum precipitation condition was at 80$\^{C}$ for 1 h for the solution with the ratio of Zn(NO$_3$)$_2$ to urea of 1 : 8. Homogeneous ZnO thin films were fabricated by the heat treatment of 600$\^{C}$ for 1 h of Zn(OH)$_2$ precipitation on Al/SiO$_2$/Si substrate. This was available to the in-situ patterned ZnO thin films with uniform grain size. Hydrophobic SAM, Octadecylphosphonic Acid(OPA) and hydrophilic SAM, 2-Carboxyethylphosphonic Acid(CPA) were applied on the Al/SiO$_2$/Si substrate by microcontact printing method. In situ patterned ZnO thin film was successfully prepared by the heat treatment of Zn(OH)$_2$ precipitated on the surface of hydrophilic SAM, CPA.