• Journal of Drive and Control
• /
• v.19 no.4
• /
• pp.29-35
• /
• 2022

In this paper, we developed a workload index for monitoring the durability test using operation information of an excavator. First, the acceleration and cylinder pressure were selected as load factors by analyzing operation data. Through load correlation analysis according to each load factor, Root Mean Square (RMS) and Work Load Range (WLR) were respectively derived as a load feature representing mechanical load. In addition, the workload index was used to quantify load features. For applying the workload index to monitoring, a real-time monitoring system consisting of sensors and embedded controller was installed on the excavator and the system was integrated with a remote monitoring environment using a wireless network. Results of load monitoring and analysis verified that the developed workload index was effective from the viewpoint of the relative comparison of the workload.

• Journal of Drive and Control
• /
• v.19 no.3
• /
• pp.39-46
• /
• 2022

In South Korea, to evaluate the rollover safety of domestic vehicles, the maximum slope angle of the vehicle is specified, which is verified by the rollover safety test of driving vehicles. However, the domestic rollover safety test is not suitable for buses, because the small amount of static stability factor (SSF) will invalidate the rollover experimental equation due to the high center of mass position of buses. To solve the above problems, a dynamic model of the bus is prepared with assumptions of mass and suspension spring properties. Subsequently, the maximum slope angle of the model was computed by using the simulation of multi-body dynamics, and the result was compared with actual test results to validate the dynamics model. Also, the rollover Fishhook (roll stability) test was conducted in the simulation for driving model. During the simulation, roll angle and roll rate were calculated to check if a rollover occurred. Through the rollover simulation of buses, the domestically regulated formula for rollover safety and the procedure of rollover test for driving vehicles are evaluated. The conclusion is that the present regulation of rollover test should be reconsidered for buses to ensure to get the valid results for rollover safety.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.16 no.2
• /
• pp.79-93
• /
• 2021

The question of why do you want to start a "start?" Is the most basic step in trying to do something. In other words, previous studies have shown that the degree of confidence in an individual's decision affects the setting of a specific purpose. Based on this, this study aims to provide basic data for deriving the direction of entrepreneurship education in college students by analyzing the effects of goal-oriented behavioral model on college students' self-determination and intention to start a business through the 5 factor model. To achieve the purpose of the study, a self-report questionnaire was conducted from October 01 to November 11, 2019 for university students attending located in Gyeonggi-do, Seoul. A total of 150 questionnaires were distributed, and 125 parts were used for the final analysis, except 25 parts with insincere responses or errors. Data were analyzed using SPSS Win 24, and reliability, validity analysis, frequency analysis, One-way ANOVA and regression analysis were performed, and three-step regression analysis and Sobel verification were performed for mediating effects. The summary of the study is as follows. First, the influence of university students' goal-oriented behavioral model on self-determination showed that attitudes, subjective norms, and perceived behavioral controls had statistically significant positive effects, and positive and negative expectations were statistically significant. Did not affect. Therefore, the higher the attitude, subjective norms, and perceived behavioral control, the higher the university students' self-determination. Second, the influence of college students' goal-oriented behavioral model on the intention to start a business was as follows.). As a result, the higher the perceived behavioral control and positive expectation, the higher the intention to start up. Third, regression model 1 showed that the behavioral control and positive expectation sentiment among the goal-oriented behavioral model had a significant positive influence on the college students' intention to start a business. Affected. Regression model II added the parameters of the 5 factor model, which increased 2.5% of explanatory power than the first regression model. Perceived behavioral control and positive expectations had a statistically significant positive effect, negative expectations had a statistically significant negative effect, and among the 5 factor model, openness had a statistically significant positive (+) Affected. From these results, it can be seen that the Big Five personality factors have a mediating effect on the relationship between goal-oriented behavior model and intention to start up. This study confirmed that the goal-oriented behavioral model of college students is an important variable in implementing self-determination and intention to start a business. In addition, by using his Big 5 personality factors as positive feedback, he has proved to play an important role by identifying the mediation role that can be set, planned and utilized to plan and achieve his life. The result of this study is that college students are interested in the intention of individual start-ups, so they are not freed from difficult employment difficulties. It is intended to provide basic data useful in the age of creation of government.

• Nutritional Sciences
• /
• v.8 no.3
• /
• pp.189-195
• /
• 2005

To assess the effect of pinitol supplementation and strength training for two weeks on the anaerobic capacity during and after exercise, and improvement of glucose metabolism during the recovery period of muscular fatigue with repeated acute bouts of cycling exercise, a total of 24 healthy young men were recruited and randomly and equally divided into three groups; pinitol supplementation group (PSG), placebo group (PLG), and control group (CON). Using a randomized double-blinded design, subjects in PSG were provided pinitol supplement, consumed orally 1.2 g/day, and participated in the resistance exercise program and cycling exercise for two weeks. Subjects in PLG underwent the same protocol as those in PSG but consumed the same amount of placebo. No supplementation and exercise program was given to CON. Before and after the intervention, all subjects were tested for their anaerobic capacities evaluated by Wingate test twice separated by 30 min. During the test, peak anaerobic power (PP), mean anaerobic power, total work, and fatigue index were evaluated During resting and recovery, blood samples were drawn and plasma pinitol, myo-inositol, chiro-inositol, insulin, free fatty acid, glucose, and lactate levels were analyzed After two weeks, PP and relative PP of the second biking were improved from the first biking in PSG only (p<0.05). No changes were found in all other variables of Wingate test in all groups. No statistical differences between groups and pre- and post-intervention were observed in concentrations of pinitol, myo-inositol, and chiro-inositol, but pinitol concentration was higher during recovery compared to the baseline in all groups and testings (p<0.05). Lactate level during recovery was higher than the resting level, but no other blood parameters were significantly changed. In conclusion, two weeks of pinitol supplementation in conjunction with short duration of anaerobic training in healthy young men did not induce any obvious benefits in terms of anaerobic capacity and energy metabolism Individual and/or population susceptibility may be one factor responsible for adopting pinitol supplementation.

• Asian Journal for Public Opinion Research
• /
• v.5 no.1
• /
• pp.41-62
• /
• 2017

The political reformation in Indonesia is a determinant factor of the change in political communications and the roles of media. Currently, the political elites need media support, since it contextually has a significant role. Whoever has a good relationship with the media, will be loved by the public. On the other hand, the media also have a vested interest in the elite in running businesses and building the power of industry. Policies and capital pose a challenge to maintaining the continuity of the media. Independence and control of media are at stake, when the interests of the media and the elite collaborate with each other and then build a benefit on both sides. Meanwhile, the role of social media also cannot be neglected. The Indonesian political communication system is characterized by the presence of social media in a pseudo-relationship between the elite and the public. This paper tries to explain the growing trends of research in the academic environment and the research trends in political practice in Indonesia after the occurrence of post-reformation era in legislative and executive elections. The method used is the meta-analysis of research outcomes of university (dissertations) and secondary data sources. Data processing is done by meta-analysis of secondary data. The results of meta-analysis research indicate that, the objective conditions, in Indonesia, especially the political conditions, stimulate new spaces in communication research. The study of political communication becomes dominant in the academic environment. In addition, communication research is also characterized by a shift from the linear perspective (positivistic paradigm) to the interactive perspective (naturalistic paradigm). On the other hand, the development of politic and governance situations in Indonesia has prompted the establishment of polling agencies that help citizens understand the maps of political power and candidates in general elections and regional head elections.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.199-206
• /
• 2006

Automatic grease lubricator is equipment that provides adequate amount of fresh grease constantly to the shaft and the bearings of machines. It minimizes the friction heat and reduces the friction loss of machines to the least. This research is to develop automatic grease lubricator by gear driven mechanism with controlled operation time. The ultimate design of this equipment is to lubricate an adequate amount of grease by a simple switch clicking according to the advanced set cycle. The backlash of the gear was minimized to increase the output power. To increase the power of gear mechanism, the binding frequency and the thickness of the coil were changed. To control the rotating cycles of the main shaft according to its set numbers, different resistance and chips were used to design the circuit to controls electrical signals with pulse. The body of the lubricator was analyzed by stress analysis with different constructed angle. The stress analysis for differing loading pressures applied to the exterior body of grease lubricator due to the setup angle, was found that the maximum stress was distributed over the outlet part where the grease lubricator suddenly narrowed contracts. Digital mock-up was analyzed and the rapid prototyping(RP) trial products were tested with PCB circuit and grease. The evaluation of the outlet capacity for RP trial products was conducted, because the friction caused by the outlet on the wall surface was an important factor in the operation of the equipment. Finally, the finishing process was applied to decrease the roughness of the surface to a comparable level and was able to test the performance examination for the product.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4447-4454
• /
• 2013

In October 2011, a commercialized 100kW class floating photovoltaic system positive plant was installed at Hapcheon dam a multi-purpose reservoir the first time ever in the nation. Floating photovoltaic system differs in water float, mooring device and underwater cable process from land photovoltaic system. As for land and building photovoltaic power generation equipments, many installation cases and skilled experiences are available, and thus installation is not difficult. However, commercial power generation floating photovoltaic system, which is attempted for the first time in the nation, requires to be designed and installed through a series of processes like technical review and verification of data by process in comparison with similar cases. The structure of floating photovoltaic system, an equipment for float photovoltaic module and other electrical equipment, is required to withstand weather environments like wind or typhoon etc and yet not affect water quality negatively, and for implementation of this system, construction efficiency and economy etc should be considered comprehensively. In this paper, the techniques of installing floating photovoltaic structure, mooring device, underwater cable, electrical equipment and remote monitoring control system are explained. The 100kW floating PV system is operating with 15% average capacity factor.

• Nuclear Engineering and Technology
• /
• v.52 no.5
• /
• pp.869-877
• /
• 2020

A 24-month Advanced Power Reactor 1400 (APR1400) core with a very-low-boron (VLB) concentration has been investigated for an inherently safe and high-performance PWR in this work. To develop a high-performance APR1400 which is able to do the passive frequency control operation, VLB feature is essential. In this paper, the centrally-shielded burnable absorber (CSBA) is utilized for an efficient VLB operation in the 24-month cycle APR1400 core. This innovative design of the VLB APR1400 core includes the optimization of burnable absorber and loading pattern as well as axial cutback for a 24-month cycle operation. In addition to CSBA, an Er-doped guide thimble is also introduced for partial management of the excess reactivity and local peaking factor. To improve the neutron economy of the core, two alternative radial reflectors are adopted in this study, which are SS-304 and ZrO₂. The core reactivity and power distributions for a 2-batch equilibrium cycle are analyzed and compared for each reflector design. Numerical results show that a VLB core can be successfully designed with 24-month cycle and the cycle length is improved significantly with the alternative reflectors. The neutronic analyses are performed using the Monte Carlo Serpent code and 3-D diffusion code COREDAX-2 with the ENDF/B-VII.1.

• Journal of the Korea Safety Management & Science
• /
• v.24 no.1
• /
• pp.61-72
• /
• 2022

This study aims to propose a conceptual design of information displays for supporting responsive actions under severe accidents in Nuclear Power Plants (NPPs). Severe accidents in NPPs can be defined as accident conditions that are more severe than a design basis accident and involving significant core degradation. Since the Fukushima accident in 2011, the management of severe accidents is increasing important in nuclear industry. Dealing with severe accidents involves several cognitively complex activities, such as situation assessment; accordingly, it is significant to provide human operators with appropriate knowledge support in their cognitive activities. Currently, severe accident management guidelines (SAMG) have been developed for this purpose. However, it is also inevitable to develop information displays for supporting the management of severe accidents, with which human operators can monitor, control, and diagnose the states of NPPs under severe accident situations. It has been reported that Ecological Interface Design (EID) framework can be a viable approach for developing information displays used in complex socio-technical systems such as NPPs. Considering the design principles underlying the EID, we can say that EID-based information displays can be useful for dealing with severe accidents effectively. This study developed a conceptual design of information displays to be used in severe accidents, following the stipulated design process and principles of the EID framework. We particularly attempted to develop a conceptual design to make visible the principle knowledge to be used for coping with dynamically changing situations of NPPs under severe accidents.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.127-132
• /
• 2022

Among the electrical components mounted on railroad cars, the largest load is the main transformer, which has a low power density of 0.2~0.4 MVA/ton due to the low operating frequency(60Hz), which is an important factor for weight reduction. Therefore, research on molded transformers, semiconductor transformers, etc. is being actively conducted at Domestic and foreign in order to improve the main transformer for railway vehicles. Meanwhile, attempts are being made to apply a permanent magnet synchronous motor (PMSM) to replace an induction motor as a traction motor that is mostly applied to domestic and foreign railway vehicles. Permanent magnet synchronous motors (PMSMs) can secure higher power density and efficiency compared to induction motors, but have disadvantages in that the materials required for manufacturing are expensive and design is somewhat difficult compared to induction motors. Considering these problems, in this paper, we suggest that a small and lightweight semiconductor transformer is applied, and a simple structure, high torque, low cost SRM can be applied in accordance with the requirements such as weight reduction and high efficiency of railroad vehicles. content.