• Resources Recycling
• /
• v.10 no.4
• /
• pp.18-23
• /
• 2001

Air pollutants, phenol was generated in case of thermal regeneration of used activated carbon loaded with phenol and because of this problem, removal process of phenol were studied. Electrolytic oxidation of samples, used S.company granular activated carbon (WS-GAC), used C.company granular activated carbon (WC-GAC) and used L.company granular activated carbon (WL-GAC) loaded with phenol carried out by potentiostatic method in this study. In case of experiment was to come into operation in condition of samples containing 100 mg/g phenol, supporting electrolyte was 1.0% sodium chloride solution, Ti-Ir (10$\times$10$\textrm{cm}^2$) electrode and electrode distance was 2 cm, current density was $1.25 A/dm^2$, Obtained from the results of electrolytic oxidation experiments were not detected residual phenol. And then we knew about reaction time of electrolytic oxidation, current density, concentration of supporting electrolyte and electrode and electrode distance were 60 minutes, 1.25 A/dm$^2$, 1.0%, 2 cm.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.34-41
• /
• 2017

The effect of Mn(II) concentration on the anodic reactions occurring on a Pb-Ag electrode in sulfuric acid solutions has been studied by potentiostatic oxidation in the potential range of 1.8 to 2.0 V. High oxidation potentials and low initial concentrations of Mn(II) resulted in higher concentrations of soluble Mn(III) ions which were obtained from spectrophotometric analysis of the solution after oxidation. $MnO_2$ was deposited on the electrode by electrochemical oxidation of Mn(II) at 1.8 and 1.9 V, while it was formed by disproportionation of Mn(III) at 2.0 V. No $PbO_2$ was formed in the presence of Mn(II) during potentiostatic oxidation treatment for two hours at 1.8 V. Chemical reduction of $PbO_2$ with Mn(II) led to a decrease in the amount of $PbO_2$ as Mn(II) concentration increased at 1.9 and 2.0 V.

• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.625-630
• /
• 2003

Increasing environmental concerns require to solve the problem produced due to the use of heavy metals in coating formulations. Therefore, it is necessary to develop new coating strategy employing inherently conducting polymers such as Polyaniline(PANI). Polyaniline films were electrosynthesized by oxidation of aniline on cold rolled and weathering sheets using the potentiostatic mode from an aqueous oxalic acid medium. Potentiodynamic polarization curves were obtained for cold rolled and weathering sheets in the aqueous solution of 3% sodium chloride. The structure and properties of polyaniline film were elucidated using SEM, DSC, SST. A high corrosion resistance of polyaniline films were observed with a gain of the corrosion potential around 600-900 mV positive in the substrate covered with polyaniline than in the case without it.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.2
• /
• pp.76-84
• /
• 2011

Potentiostatic oxidation of Pb-1.7%Sb alloy used in the manufacture of grids of lead-acid batteries over the potential range from -1.0V to 2.3V in 5M $H_2SO_4$ in the absence and the presence of 0.4M $H_3PO_4$ and the self-discharge characteristics of the oxide layer formed is studied by electrochemical impedance spectroscopy (EIS). Depending on the potential value, sharp variations in resistance and capacitance of the alloy are recorded during the oxidation and they can be used for identification of the various substances involved in passive layer. Addition of $H_3PO_4$ is found to deteriorate the insulating properties of the passive layer by the retardation of the formation of $PbSO_4$. $H_3PO_4$ completely inhibits the current and impedance fluctuations recorded in $H_3PO_4$-free solutions in the potential range 0.5 V-1.7 V. These fluctuations are attributed to the occurrence of competitive redox processes that involve the formation of $PbSO_4$, $PbOSO_4$, PbO and $PbO_2$ and the repeated formation and breakdown of the passive layer. Self-discharge experiments indicate that the amount of $PbO_2$ formed in the presence of $H_3PO_4$ is lesser than in the $H_3PO_4$-free solutions. The start of transformation of $PbSO_4$ into $PbO_2$ is greatly shortened. $H_3PO_4$ facilitates the diffusion process of soluble species through the passive layer ($PbSO_4$ and basic $PbSO_4$) but impedes the diffusion process through $PbO_2$.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.3
• /
• pp.179-186
• /
• 2014

Methanol electro oxidation on the surface of carbon paste modified by $NiCl_2/6H_2O$ was studied in 1M NaOH by potentiostatic and potentiodynamic methods. Ni/C catalyst by the concentration of 5% Ni showed about twice higher electro catalytic activity than Ni metal. The amount of monolayer's on the surface of electrode is almost one order higher for Ni/C than Ni electrode. The kinetic parameters and the diffusion coefficient of methanol were derived from chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS) measurements.

• Journal of the Korean Chemical Society
• /
• v.66 no.6
• /
• pp.436-441
• /
• 2022

Because the nanoporous electrodes has large electrochemical surface areas, extensive studies have been focused on their fabrication methods. In this paper, a method for introducing a nanoporous gold (NPG) structure on the surface of an ultramicroelectrode (UME) using potentiostatic anodization was investigated. A well-defined NPG structure was introduced on the surface of the UME when a potential of 1.3 V was applied in 0.1 M phosphate buffer solution (pH 8) containing 1 M KCl. The anodic oxidation efficiency was investigated by observing the effect of the applied potential, the reaction time, and the size of the electrode on the roughness factor (R_f) of the prepared NPG-UMEs. In a short time of about 10 minutes, NPG-UME with a large R_f value of about 2000 could be prepared, which could be effectively used for electrochemical glucose detection. The results shown in this work are expected to have great applicability when performing electrochemical analysis with a small sample volume.

• Journal of Electrochemical Science and Technology
• /
• v.1 no.1
• /
• pp.10-18
• /
• 2010

Controlled electrodeposition of dendritic nano-structured gold-platinum (AuPt) alloy onto an electrochemically pretreated carbon paper substrate was conducted in an attempt to improve catalyst utilization and to secure an electronic percolation network toward formic acid (FA) fuel cell application. The AuPt catalysts were obtained by potentiostatic deposition. AuPt catalysts synthesized as bimetallic alloys with 60% Au content exhibited the highest catalytic activity towards formic acid electro-oxidation. The origin of this high activity and the role of Au were evaluated, in particular, by XPS analysis. Polarization and stability measurements with 1 mg $cm^{-2}$ AuPt catalyst (only 0.4 mg $cm^{-2}$ Pt) showed 52 mW $cm^{-2}$ and sustainable performance using 3M formic acid and dry air at $40^{\circ}C$.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.1
• /
• pp.17-23
• /
• 2005

The electrochemical behaviors of polycrystalline silver electrodes in 8M KOH solutions containing $Bi_2O_3$ were studied under various conditions by cyclic voltammetry, potentiostatic and galvanostatic techniques as well as the morphology of the silver oxide structures by SEM. It was found that three new compounds comprising silver, bismuth, and oxygen as well as $Bi_2O_3$, $Ag_2O$ and AgO were formed during the electrochemical oxidation of silver. In addition, the potentiostatic current transients were characterized by the appearances of the first current peaks corresponding to the formation of silver oxides, and the second current peaks corresponding to the Ag-Bi-O compounds, indicating the presence of the nucleation and 3D growth mechanism, in the potential regions of $Ag_2O$ and AgO, respectively. Microscopic examinations showed that two types of silver (I) oxide morphologies are formed in the potential region of $Ag_2O$.

• Bulletin of the Korean Chemical Society
• /
• v.9 no.4
• /
• pp.248-251
• /
• 1988

Mechanism of electrochemical polymerization of pyrrole (Py) on a Pt electrode in acidic aqueous solutions was studied by means of potentiostatic measurements, cyclic voltammetry and chronopotentiometry. Pyrrole molecule appeared to be initially oxidized via two-electron transfer step to produce oxidized pyrrole ion ($Py^+$), which was coupled with a non-oxidized pyrrole to yield a dimerized species, Py-Py. The Py-Py thus formed was further oxidized again via two-electron transfer step, which was followed by coupling with non-oxidized monomer and by concomitant expulsion of a $H^+$. Then the latter chain extension process was repeated. The chain extension and polypyrrole oxidation reactions occurred competitively.

• Journal of Powder Materials
• /
• v.17 no.3
• /
• pp.216-222
• /
• 2010

Self-standing $TiO_2$ nanotube arrays were fabricated by potentiostatic anodic oxidation method using pure Ti foil as a working electrode and ethylene glycol solution as electrolytes with small addition of $NH_4F$ and $H_2O$. The influences of anodization temperature and time on the morphology and formation of $TiO_2$ nanotube arrays were investigated. The fabricated $TiO_2$ nanotube arrays were applied as a photoelectrode to dye-sensitized solar cells. Regardless of anodizing temperature and time, the average diameter and wall thickness of $TiO_2$ nanotube show a similar value, whereas the thickness show a different trend with reaction temperature. The thickness of $TiO_2$ nanotube arrays anodized at $20^{\circ}C$ and $30^{\circ}C$ was time-dependent, but on the other hand its at $10^{\circ}C$ are independent of anodization time. The conversion efficiency is low, which is due to a morphology breaking of the $TiO_2$ nanotube arrays in manufacturing process of photoelectrode.