• 제목/요약/키워드: post-curing

검색결과 138건 처리시간 0.021초

도재 수리 시스템의 전단결합강도에 관한 연구 (Shear Bond Strength of Porcelain Repair Systems)

  • 우수;신수연;조인호
    • 구강회복응용과학지
    • /
    • 제22권3호
    • /
    • pp.211-220
    • /
    • 2006
  • Need of porcelain-repair system is largely demanding as dental porcelain restorations are increased in clinical dentistry. This study investigated shear bond strength of commercial porcelain-repair systems on dental porcelain and their reliability. Experimental groups were as follows; Group A Super Bond C&B, Group B Porcelain repair kit, Group C Ceramic repair, and Group D Spectrum system as a control. Porcelain disks were fired and embedded in epoxy resin. Porcelain surface were ground using 220 grit SiC disk, then cleaned in ultrasonic bath. Then porcelain specimens were treated with each repair system. A clear polystyrene cylinder 3.5 mm in internal diameter was filled with composite resin. Then the resin cylinder was polymerized with a visible light curing unit. Thirty one specimens at each group were prepared and stored at $37^{\circ}C$ distilled water for 48 h. Specimens were tested in an Instron testing machine according to ISO TR 11405. Mean shear bond strength and standard deviation of each group was $15.7{\pm}4.1MPa$ (Group A), $12.8{\pm}4.9MPa$ (Group B), $7.2{\pm}3.0MPa$ (Group C) and $9.6{\pm}2.2MPa$ (Group D). ANOVA and Tukey HSD post-hoc test showed that there were significant differences between groups (p<0.05). Data of bond strength were analyzed with two-parameter Weibull distribution. Confidence interval of Weibull modulus (m-parameter) at 95% of Group A (3.5-6.3) and Group D (3.6-6.0) were significantly higher than Group B (2.2-3.7) and Group C (2.0-3.4). There was little correlation between mean shear bond strength and Weibull modulus. Results indicated that acid-etching of porcelain surface increased porcelain-resin shear bonding strength.

Light transmittance of CAD/CAM ceramics with different shades and thicknesses and microhardness of the underlying light-cured resin cement

  • Jafari, Zahra;Alaghehmand, Homayoon;Samani, Yasaman;Mahdian, Mina;Khafri, Soraya
    • Restorative Dentistry and Endodontics
    • /
    • 제43권3호
    • /
    • pp.27.1-27.9
    • /
    • 2018
  • Objectives: The aim of this in vitro study was to evaluate the effects of the thickness and shade of 3 types of computer-aided design/computer-aided manufacturing (CAD/CAM) materials. Materials and Methods: A total of 120 specimens of 2 shades (A1 and A3) and 2 thicknesses (1 and 2 mm) were fabricated using VITA Mark II (VM; VITA Zahnfabrik), IPS e.max CAD (IE; IvoclarVivadent), and VITA Suprinity (VS; VITA Zahnfabrik) (n = 10 per subgroup). The amount of light transmission through the ceramic specimens was measured by a radiometer (Optilux, Kerr). Light-cured resin cement samples (Choice 2, Bisco) were fabricated in a Teflon mold and activated through the various ceramics with different shades and thicknesses using an LED unit (Bluephase, IvoclarVivadent). In the control group, the resin cement sample was directly light-cured without any ceramic. Vickers microhardness indentations were made on the resin surfaces (KoopaPazhoohesh) after 24 hours of dark storage in a $37^{\circ}C$ incubator. Data were analyzed using analysis of variance followed by the Tukey post hoc test (${\alpha}=0.05$). Results: Ceramic thickness and shade had significant effects on light transmission and the microhardness of all specimens (p < 0.05). The mean values of light transmittance and microhardness of the resin cement in the VM group were significantly higher than those observed in the IE and VS groups. The lowest microhardness was observed in the VS group, due to the lowest level of light transmission (p < 0.05). Conclusion: Greater thickness and darker shades of the 3 types of CAD/CAM ceramics significantly decreased the microhardness of the underlying resin cement.

Effect of Thermal Imidization and Curing on Fluorescence Behavior of a Phenylethynyl-Terminated Poly(amic acid)

  • Cho, Donghwan;Yang, Gyeongmo;Drzal, Lawrence T.
    • Macromolecular Research
    • /
    • 제11권5호
    • /
    • pp.297-302
    • /
    • 2003
  • The imidization and cure reaction of a thermosetting phenylethynyl-terminated amic acid (LaRC PETI-5) in film form have been monitored as a function of temperature by means of a steady-state fluorescence technique using a front-face illumination method. The variation of the fluorescence emission spectra of LaRC PETI-5 can be divided into four temperature regions; Region I: below 15$0^{\circ}C$, Region II: 150-25$0^{\circ}C$, Region III: 250-35$0^{\circ}C$, and Region IV: above 35$0^{\circ}C$. The fluorescence spectra in Region I are largely influenced by residual N-methyl-2pyrrolidinone in the polymer and also slightly by partial imidization of the polymer. There is a combined effect of imidization and solvent removal on the fluorescence behavior in Region II. The spectra in Regions III and IV are due significantly to the cure reaction of LaRC PETI-5 and to a post-cure effect of the polyimide, respectively. This spectroscopic evidence indicating the transformation of the amic acid imide oligomer into the corresponding polyimide via imidization and cure, agrees well with thermal analysis results obtained previously. The intermediate stage of cure in the range of 250-30$0^{\circ}C$ predominantly influences the change of the fluorescence intensity. The later stage above 30$0^{\circ}C$ significantly influences the position of the spectrum. This fluorescence study also supports the mechanism proposed in earlier work that the crosslinking reaction takes place at the reaction sites in the conjugated polyene and the phenylethynyl end group in the polyimide chain.

Bond strength of resin cement to $CO_2$ and Er:YAG laser-treated zirconia ceramic

  • Kasraei, Shahin;Rezaei-Soufi, Loghman;Heidari, Bijan;Vafaee, Fariborz
    • Restorative Dentistry and Endodontics
    • /
    • 제39권4호
    • /
    • pp.296-302
    • /
    • 2014
  • Objectives: It is difficult to achieve adhesion between resin cement and zirconia ceramics using routine surface preparation methods. The aim of this study was to evaluate the effects of $CO_2$ and Er:YAG laser treatment on the bond strength of resin cement to zirconia ceramics. Materials and Methods: In this in-vitro study 45 zirconia disks (6 mm in diameter and 2 mm in thickness) were assigned to 3 groups (n = 15). In control group (CNT) no laser treatment was used. In groups COL and EYL, $CO_2$ and Er:YAG lasers were used for pretreatment of zirconia surface, respectively. Composite resin disks were cemented on zirconia disk using dual-curing resin cement. Shear bond strength tests were performed at a crosshead speed of 0.5 mm/min after 24 hr distilled water storage. Data were analyzed by one-way ANOVA and post hoc Tukey's HSD tests. Results: The means and standard deviations of shear bond strength values in the EYL, COL and CNT groups were $8.65{\pm}1.75$, $12.12{\pm}3.02$, and $5.97{\pm}1.14MPa$, respectively. Data showed that application of $CO_2$ and Er:YAG lasers resulted in a significant higher shear bond strength of resin cement to zirconia ceramics (p < 0.0001). The highest bond strength was recorded in the COL group (p < 0.0001). In the CNT group all the failures were adhesive. However, in the laser groups, 80% of the failures were of the adhesive type. Conclusions: Pretreatment of zirconia ceramic via $CO_2$ and Er:YAG laser improves the bond strength of resin cement to zirconia ceramic, with higher bond strength values in the $CO_2$ laser treated samples.

결합부 강화구조용 탄소복합재 자동차 부품 개발 (Development of the CFRP Automobile Parts Using the Joint Structure of the Dissimilar Material)

  • 고관호;이민구;허몽영
    • Composites Research
    • /
    • 제31권6호
    • /
    • pp.392-397
    • /
    • 2018
  • 본 연구에서는 기존의 스틸재 타이로드를 브레이딩 공법을 적용한 탄소복합재로 개발하고자 하였다. 탄소복합재 타이로드는 기존 제품과 동등한 성능을 만족시키기 위하여 브레이딩 직조에 필요한 코어 단면설계, 코어와 탄소섬유의 접합부에 대한 구조형상설계를 진행하였다. 그리고 브레이딩 공법을 적용한 시편을 제작하여 시험평가를 통해 구조해석에 적용하였다. 제작 공정은 브레이딩 직조 후 인퓨전 공정을 거쳐 후경화 공정까지 진행하였으며 최종 제품에 대한 시험평가는 인장 시험, 비틀림 시험, 압축 시험과 피로시험을 순차적으로 진행하여 모두 만족시켰다. 또한 탄소복합재 타이로드의 중량을 기존 제품 대비 약 37% 정도 경량화시킬 수 있었다.

수소버스용 내압용기 복합재의 열적환경에 따른 기계적 물성 연구 (High Temperature Tensile Stress Behavior of Hydrogen Vessel Composite Materials for Hydrogen Fuel Cell Bus)

  • 양현석;정우철;신광복;공만식
    • Composites Research
    • /
    • 제35권6호
    • /
    • pp.425-430
    • /
    • 2022
  • 수소가스용 압력용기의 안전성 평가를 위해 다양한 내구성 시험이 요구된다. 고온 정압 시험은 고압(875 bar) 하에 고온(85℃ 이상)에서 장시간(1,000시간) 유지하여 수소 용기의 내구성을 시험하는 방법이며 승용차용 용기에 한정되어 있다. 하지만 대용량 수소버스용 용기와 관련된 고온 정압 시험의 국제 기준은 논의 초기 단계이며, 시험의 효율성 및 신뢰성 측면에서 가속시험 기준 제시 등의 현실적 보완이 필요하다. 본 연구에서는 수소버스용 내압용기의 고온 정압 시험 기준을 정립하기 위해 열적환경에 노출된 내압용기 복합재의 기계적 물성평가를 진행하였다. 복합재의 인장강도는 수지의 유리전이온도에 가까워질수록 수지의 열화로 인해 강도가 감소한다. 또한 장시간 유지 시 수지의 후경화로 인해 인장강도의 재상승을 확인할 수 있었다. 따라서 대용량 수소버스용 압력용기의 고온 정압 시험은 탄소섬유 복합재의 에폭시 수지 물성을 바탕으로 시험 조건을 설정해야 한다.

Comparison between a bulk-fill resin-based composite and three luting materials on the cementation of fiberglass-reinforced posts

  • Carlos Alberto Kenji Shimokawa ;Paula Mendes Acatauassu Carneiro ;Tamile Rocha da Silva Lobo;Roberto Ruggiero Braga ;Miriam Lacalle Turbino;Adriana Bona Matos
    • Restorative Dentistry and Endodontics
    • /
    • 제48권3호
    • /
    • pp.30.1-30.11
    • /
    • 2023
  • Objectives: This study verified the possibility of cementing fiberglass-reinforced posts using a flowable bulk-fill composite (BF), comparing its push-out bond strength and microhardness with these properties of 3 luting materials. Materials and Methods: Sixty endodontically treated bovine roots were used. Posts were cemented using conventional dual-cured cement (CC); self-adhesive cement (SA); dual-cured composite (RC); and BF. Push-out bond strength (n = 10) and microhardness (n = 5) tests were performed after 1 week and 4 months of storage. Two-way repeated measures analysis of variance (ANOVA), 1-way ANOVA, t-test, and Tukey post-hoc tests were applied for the push-out bond strength and microhardness results; and Pearson correlation test was applied to verify the correlation between push-out bond strength and microhardness results (α = 0.05). Results: BF presented higher push-out bond strength than CC and SA in the cervical third before aging (p < 0.01). No differences were found between push-out bond strength before and after aging for all the luting materials (p = 0.84). Regarding hardness, only SA presented higher values measured before than after aging (p < 0.01). RC and BF did not present 80% of the maximum hardness at the apical regions. A strong positive correlation was found between the luting materials' push-out bond strength and microhardness (p < 0.01, R2 = 0.7912). Conclusions: The BF presented comparable or higher push-out bond strength and microhardness than the luting materials, which indicates that it could be used for cementing resin posts in situations where adequate light curing is possible.

Enrichment of Pork with Omega-3 Fatty Acids by Tuna Oil Supplements: Effects on Performance as well as Sensory, Nutritional and Processing Properties of Pork

  • Jaturasitha, S.;Wudthithumkanaporn, Y.;Rurksasen, P.;Kreuzer, M.
    • Asian-Australasian Journal of Animal Sciences
    • /
    • 제15권11호
    • /
    • pp.1622-1633
    • /
    • 2002
  • The effects of tuna oil supplementation (0, 1, 2 and 3%) to pig diets on growth and carcass yield as well as meat quality were determined in 40 crossbred pigs. Animals were fattened from 30 to 90 kg of live-weight. Twenty-four hours after slaughter, following various early- and late-post mortem measurements, loin, backfat and belly were prepared from the carcasses. Bacon was produced from the belly part by curing and smoking. Neither performance (feed intake, daily gains, feed conversion efficiency) nor carcass quality (slaughter weight, dressing percentage, lean percentage, nutrient composition of the loin) were significantly affected by tuna oil supplementation. Tuna oil also had no clear effects on early- and late-post mortem meat quality traits, water-holding capacity and tenderness of the M. longissiumus dorsi (LD). Colour traits of LD and backfat, and backfat firmness were not significantly affected by tuna oil, either. However, there was a certain trend to elevated fat contents of LD (and bacon), but not of backfat, with increasing levels of tuna oil in feed. Pigs receiving elevated proportions of tuna oil expressed lower VLDL cholesterol and triglyceride concentrations in blood plasma, whereas the cholesterol content of LD, backfat and bacon did not reflect this trend. Effects of tuna oil on fatty acids in LD, backfat and bacon were often small in extent, except those concerning the long-chain polyunsaturated fatty acids. With 3% tuna oil in the diet, the contents of the particularly desired omega-3 fatty acids, C20:5 and C22:6, were 0.1 and 0.2 g/kg in LD. The corresponding values for backfat and bacon were 2.6 and 12.6 g/kg, and 1.3 and 9.2 g/kg, respectively. Tuna oil supplementation was associated with significant adverse effects on flavour and overall acceptance of bacon (not significant in LD although numerically the same trend was noted), but these effects on sensory ratings were limited in extent. Also shelf life of the products, determined as TBA value after different storage periods at $4^{\circ}C$ in LD, backfat and bacon, was significantly reduced. Overall, the present study suggests that omega-3 fatty acids may be enriched in pork by feeding tuna oil with few undesired side-effects, particularly those on sensory perception and shelf life, suggesting immediate consumption of the products is advisable. Most economically important traits (performance, slaughter and physical meat quality) remained unaffected.

음향방출법에 의한 탄소 섬유 복합 재료의 인장 및 파괴 인성시험시의 파괴 거동에 관한 연구 (A Study on the Fracture Behavior of CFRP in Tensile and Fracture Toughness Tests by Acoustic Emission)

  • 이상국;오세규;남기우;김옥균
    • 비파괴검사학회지
    • /
    • 제15권1호
    • /
    • pp.277-290
    • /
    • 1995
  • 본 연구는 $[0^{\circ}/90^{\circ}]_{2S}$$[0^{\circ}\;_2/90^{\circ}\;_2]_S$의 2종류 탄소섬유복합재료에 대한 인장 및 파괴인성 시험시의 파괴거동과 음향방출 특성을 해석하고 성형시의 성형압력과 인장강도 및 파괴인성 간의 상관성을 알아내기 위하여 수행되었다. AE신호는 음향방출장비를 이용하여 성형과정, 인장 및 파괴인성 시험중에 각각 검출하였다. 인장강도는 성형가압 단계수가 적을수록, 그리고 $[0^{\circ}/90^{\circ}]_{2S}$ 시험편 쪽이 $[0^{\circ}\;_2/90^{\circ}\;_2]_S$ 시험편보다 높은 강도를 나타내었다. 파괴인성은 동일한 온도영역에서 거의 같은 값을 나타내나 시험온도가 높아질수록 점차 낮아짐을 알 수 있었다. 한편 인장 및 파괴인성 시험시의 파괴거동과 AE신호간의 상관성을 조사하기 위하여 AE데이터의 AE변수들에 대한 후 신호처리(post processing)와 광학현미경 및 주사형 전자현미경 관찰이 각각 수행되었다.

  • PDF

Comparison of Flexural Strength of Three-Dimensional Printed Three-Unit Provisional Fixed Dental Prostheses according to Build Directions

  • Park, Sang-Mo;Park, Ji-Man;Kim, Seong-Kyun;Heo, Seong-Joo;Koak, Jai-Young
    • Journal of Korean Dental Science
    • /
    • 제12권1호
    • /
    • pp.13-19
    • /
    • 2019
  • Purpose: The aim of this study was to compare the flexural strength of provisional fixed dental prostheses which was three-dimensional (3D) printed by several build directions. Materials and Methods: A metal jig with two abutment teeth and pontic space in the middle was fabricated. This jig was scanned with a desktop scanner and provisional restoration was designed on dental computer-aided design program. On the preprocessing software, the build angles of the restorations were arranged at $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$ and support was added and resultant structure was sliced to a thickness of $100{\mu}m$. Processed restorations were printed with digital light processing type 3D printer using poly methyl meta acrylate-based resin. After washing and post-curing, compressive loading was applied at a speed of 1 mm/min on a metal jig fixed to a universal testing machine. The maximum pressure at which fracture occurred was measured. For the statistical analysis, build direction was set as the independent variable and fracture strength as the dependent variable. One-way analysis of variance and Tukey's post hoc analysis was conducted to compare fracture strength among groups (${\alpha}=0.05$). Result: The mean flexural strength of provisional restoration 3D printed with the build direction of $0^{\circ}$ was $1,053{\pm}168N$; it was $1,183{\pm}188N$ at $30^{\circ}$, $1,178{\pm}81N$ at $45^{\circ}$, $1,166{\pm}133N$ at $60^{\circ}$, and $949{\pm}170N$ at $90^{\circ}$. The group with a build direction of $90^{\circ}$ showed significantly lower flexural strength than other groups (P<0.05). The flexural strength was significantly higher when the build direction was $30^{\circ}$ than when it was $90^{\circ}$ (P<0.01). Conclusion: Among the build directions $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$ set for 3D printing of fixed dental prosthesis, an orientation of $30^{\circ}$ is recommended as an effective build direction for 3D printing.