• Ocean and Polar Research
• /
• 제36권1호
• /
• pp.25-37
• /
• 2014

To understand the degradation processes of organic matter related to sulfate reduction by Sulfate Reduction Bacteria (SRB) in the tidal flat sediments of Hwang-do and Sogeun-ri, Tae-an Peninsula in Chungnam-do, biogeochemical characteristics were analyzed and highlighted using specific microbial biomarkers. The organic geochemical parameters (TOC, ${\delta}^{13}C_{org}$, C/N ratio, long-chain-n-alkane) indicate that most of the organic matter has been derived from marine phytoplankton and bacteria in the fine-grained sediment of Sogeun-ri, although terrestrial plant components have occasionally been incorporated to a significant degree in the coarse-grained sediment of Hwang-do. The concentration of sulfate in pore water is a constant tendency with regard to depth profile, while methane concentration appears to be slightly different with regard to depth profile at the two sites. Especially, the sum of bacteria fatty acid (a-C15:0 + i-C15:0 + C16:1w5) confirms that the these concentrations in Sogeun-ri are related to the degradation of Benzene, Toluene, Ethylbenzene and Xylene (BTEX) compounds from the crude oil retained in the sediments as a result of the Hebei Spirit oil-spill accident in 2007. The methane-related microbial communities as shown by lipid biomarkers (crocetane, PMI) are larger in some sedimentary sections of Hwang-do than in the Sogeunri tidal flat. These findings suggest that methane production by microbiological processes is clearly governed by SRB activity along the vertical succession in organic-enriched tidal flats.

• Membrane and Water Treatment
• /
• 제11권2호
• /
• pp.97-109
• /
• 2020

Membrane fouling is the main drawback of membrane technology. Frequent membrane cleaning and membrane replacement are, therefore, required to reduce membrane fouling that causes permeate flux reduction, lower rejection, or higher operating pressure. Studies have proved that the alteration of membrane properties is the key controlling factor in lessening membrane fouling. Among stimuli-responsive membranes, thermo-responsive membrane is the most popular, with a drastic phase transition and swelling-shrinking behavior caused by the temperature change. In this study, the thermo-responsive ability of two commercial membranes, PolyCera® Titan membrane and PolyCera® Hydro membrane, at different temperatures was studied on the antifouling function of the membrane in palm oil mill effluent (POME) treatment. The evaluation of the membrane's thermo-responsive ability was done through three cycles of adsorption (fouling) and desorption (defouling) processes in a membrane filtration process. The experimental result depicted that PolyCera® Hydro membrane had a higher membrane permeability of 67.869 L/㎡.h.bar than PolyCera® Titan membrane at 46.011 L/㎡.h.bar. However, the high membrane permeability of PolyCera® Hydro membrane was compensated with low removal efficiency. PolyCera® Titan membrane with a smaller mean pore size had better rejection performance than PolyCera® Hydro membrane for all tested parameters. On the other hand, PolyCera® Titan membrane had a better hydrodynamic cleaning efficiency than PolyCera® Hydro membrane regardless of the hydrodynamic cleaning temperature. The best hydrodynamic cleaning performed by PolyCera® Titan membrane was at 35℃ with the flux recovery ratio (FRR) of 99.17 ± 1.43%. The excellent thermo-responsive properties of the PolyCera® Titan membrane could eventually reduce the frequency of membrane replacement and lessen the use of chemicals for membrane cleaning. This outstanding exploration helps to provide a solution to the chemical industry and membrane technology bottleneck, which is the membrane fouling, thus reducing the operating cost incurred by the membrane fouling.

• Fisheries and Aquatic Sciences
• /
• 제3권1호
• /
• pp.26-32
• /
• 2000

Monospecific red tide by a toxic dinoflagellate belonging to the genus Alexandrium occurred at Chindong Bay in the southern coast of Korea and continued from April 6th to 15th in 1997. The ratio of its cell number to total phytoplankton cell number was much higher than $95\%$. This organism was identified as Alexandrium tamarense, although slight morphological differences were found comparing to the original and successive descriptions of the species. We found neither anterior nor posterior attachment pores in these cells of the bloom population. The occurrence of red tide caused by A. tamarense was first reported in Korea. Its plate formula is Po, Pc, 4', 6"c, 8s, 5"' and 2"". Thecal plates are thin with pore-like ornamentation. In those plates, the anterior part of the first apical plate (1') is narrower and its posterior end has sometimes a block-like accessory, but this variation was considered within the range of the morphological variability of this taxon. The cell density during the red tide exhibited a wide range of variation by the depth of water column, ranging from $2\times10^6$ cells$l^{-1}$ to $5\times10^6$ cells·$l^{-1}$. Water temperature varied from 11.8 to $12.3^{\circ}C$. Toxicity of A. tamarense during red tide was measured as $8.8\times10^5$. $MU\;\cdot\;cell^{-1}$ by mouse bioassay.

• Corrosion Science and Technology
• /
• 제8권3호
• /
• pp.110-115
• /
• 2009

At the onset of corrosion of steel in concrete, hydrogen ions usually evolve in the process of electrochemical reaction, thereby decreasing the pH of the pore solution, which can be buffered by cement hydration products, as being representatively illustrated by calcium hydroxide. Hence, a fall in the pH is dependent on properties of cement hydration (i.e. hydration products and degree of hydration). The present study tested acid neutralization capacity (ANC) of cementitious binders of OPC(Ordinary Portland Cement), 30% PFA(Pulverized Fuel Ash), 60% GGBS(Ground Granulated Blast Furnace Slag), 10% SF(Silica Fume) to quantify the resistance of cement matrix to a pH fall. Cement pastes were cast at 0.4 of a free W/C ratio with 1.5% chlorides by weight of binder in cast. Powder samples obtained crushed and ground specimen after 200 days of curing were diluted in still water combined with different levels of 1M nitric acid solution, ranging from 0.5 to 20 mol/kg. Then, the pH of diluted solution was monitored until any further change in the pH did not take place. It was seen that the pH of the diluted solution gradually decreased as the molar amount of nitric acid increased. At some particular values of the pH, however, a decrease in the pH was marginal, which can be expressed in the peak resistances to a pH fall in the ANC curve. The peaks occurred at the variations in the pH, depending on binder type, but commonly at about 12.5 in the pH, indicate a resistance of precipitated calcium hydroxide. The measurement of water soluble chloride at the end of test showed that the amount of free chloride was significantly increased at the pH corresponding to the peaks in the ANC curve, which may reflect the adsorption of hydration products to chlorides.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.631-642
• /
• 2010

This study is experimentally investigated for the characteristics of compression and tensile of lightweight air-trapped soils with uniform quality. Previously, EPS blocks are often used as lightweight embankment, but many problems such as the level difference and cracks caused by plastic(creep) deformation occurred in the EPS blocks. So, a new material development is urgent. By means of alternatives, lightweight air-mixed soil using in-situ soils has been developed and applied to fields. In comparison with EPS block, lightweight air-mixed soil have less creep deformation in long-time, but the strength characteristics of them are different depending on soils where they are obtained. Therefore, the quality management of them is very difficult. In this study, therefore, characteristics of lightweight air-trapped soil samples are investigated. To do this, the lightweight air-trapped soils are prepared using a manufactured sand with uniform quality. To found out the compression and tensile characteristics of lightweight air-tapped soils, unconfined compression test and splitting tensile test are conducted on the specimens prepared with different unit weight, cement-sand ratio and air-pore.

• 한국지반환경공학회 논문집
• /
• 제18권12호
• /
• pp.5-11
• /
• 2017

농촌 비닐하우스에서 배출되는 폐비닐을 녹여 19mm 크기의 골재를 만들었다. 이것을 아스콘에 몇몇 중량비로 혼합한 후 단열효과시험, 동결융해 후 인장강도시험, 빙착인장강도시험 그리고 현장 밀도시험을 각각 실시하였다. 그 결과 폐비닐골재는 내부에 공극을 다수 포함하고 있는 관계로 폐비닐골재 혼합율이 증가할수록 단열효과가 증가하였다. 아스콘의 동결융해 후 인장강도는 폐비닐골재 혼합율 0%일 때보다 혼합율 2.5%일 경우 크게 증가하였지만, 혼합율 5%, 10%에서는 혼합율 2.5%일 때보다 다소 감소하는 경향을 보였다. 빙착인장강도는 일반아스콘에 비해 폐비닐골재를 2.5% 추가한 아스콘에서 더 작게 나타났다. 현장 채취시료에 대한 공극률시험 결과 폐비닐골재를 추가한 아스콘의 공극률이 일반 아스콘의 그것보다 작았다.

• 한국세라믹학회지
• /
• 제52권6호
• /
• pp.455-461
• /
• 2015

Porous ceramics with tailored pore size and shape are promising materials for the realization of a number of functional and structural properties. A novel method has been reported for the investigation of the role of SiC in the formation of $SiO_2$ foams by colloidal wet processing. Within a suitable pH range of 9.9 ~ 10.5 $SiO_2$, particles were partially hydrophobized using hexylamine as an amphiphile. Different mole ratios of the SiC solution were added to the surface modified $SiO_2$ suspension. The contact angle was found to be around $73^{\circ}$, with an adsorption free energy $6.8{\times}10^{-12}J$. The Laplace pressure of about 1.25 ~ 1.6 mPa was found to correspond to a wet foam stability of about 80 ~ 85%. The mechanical and thermal properties were analyzed for the sintered ceramics, with the highest compressive load observed at the mole ratio of 1:1.75. Hertzian indentations are used to evaluate the damage behavior under constrained loading conditions of $SiO_2$-SiC porous ceramics.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.69-74
• /
• 2006

Recently, spillways are need to control stable water level for supporting main dams because of floods by unusual change of weather such as Typhoon Rusa. This study has been focused on the amount of leakage through the rock mass distributed fractures and joints under the opened emergency spillway. It is very important to evaluate the amount of leakage as these affect stability of spillway by interaction between effective stress and pore pressure. The commercial program MAFIC has been used for analyzing groundwater flow in fractured rock mass. The results showed that the values of range, average and deviation of leakage were $2.85\sim\;3.79\times10^{-1}$, $3.32\times10^{-1}$ and $1.70\times10^{-2}\;m^3/day/m^2$ respectively. Secondary, we have estimated the effect of grouting after the transmissivity$(T_f)$ of joint 1 as main pathway of leakage known from above results was changed from $1.78\times10^{-7}$ to $1.59\times10^{-9}\;m^2/s$. The results showed that the values of range, average and deviation of leakage were $7.80\times10^{-4}\sim1.53\times10^{-3}$, $1.18\times10^{-3}$ and $1.32\times10^{-4}\;m^3/day/m^2$ respectively. As the result, the amount of leakage after grouting has been decreased by a ratio of 1 to 277.

• 한국세라믹학회지
• /
• 제40권6호
• /
• pp.553-559
• /
• 2003

PDP(Plasma Display Panel) rib은 고정세의 패턴 설계 및 복잡, 다양한 공정으로 제조되고 있다. Rib은 PDP제조 공정 및 역할상 매우 중요한 부분의 하나이며 rib의 소결 정도는 cross-talk와 같은 현상을 방지하는 데에 중요한 역할을 한다. 저렴하고 높은 양산성을 가진 rib은 주로 스크린 프린팅법에 의해 제작되지만, 인쇄, 소성 등 일련의 제조 공정을 거친 후 얻어진 수백 $\mu\textrm{m}$ 미세규격의 격벽 소결체의 소결도를 정확히 평가하기는 쉽지 않다. 본 연구에서는 rib의 소결도를 직접적 판단할 수 있는 방법에 대한 연구의 일환으로서 주로 소결 말기에 나타나는 기공의 응집, 성장을 potentiostat로 기공에서의 절연 파괴, 전계 집중의 원리를 이용함으로서 소결도를 측정했다 이 측정값은 각 온도에서 열처리한 시편에 대한 밀도값과 유사한 경향성이 나타남을 확인할 수 있었다 개기공, 폐기공의 분포에 따라 예상될 수 있는 측정오차는 온도에 따른 미세구조의 변화를 수차례의 전자 현미경 관찰을 통해 확인, 검증하여 미세규격 rib 소결도의 판단을 전기화학적 방법으로 예측 가능하다는 것을 알 수 있었다.

• 구강회복응용과학지
• /
• 제21권1호
• /
• pp.33-42
• /
• 2005

This study was performed to investigate the surface properties and in vitro biocompatibility of electrochemically oxidized Ti-6Al-7Nb alloy by anodic spark discharge technique. Discs of Ti-6Al-7Nb alloy of 20 mm in diameter and 2 mm in thickness were polished sequentially from #300 to 1000 SiC paper, ultrasonically washed with acetone and distilled water for 5 min, and dried in an oven at $50^{\circ}C$ for 24 hours. Anodizing was performed using a regulated DC power supply. The applied voltages were given at 240, 280, 320, and 360 V and current density of $30mA/cm^2$. Hydrothermal treatment was conducted by high pressure steam at $300^{\circ}C$ for 2 hours using a autoclave. Samples were soaked in the Hanks' solution with pH 7.4 at $36.5^{\circ}C$ during 30 days. The results obtained were summarized as follows; 1. The oxide films were porous with pore size of $1{\sim}5{\mu}m$. The size of micropores increased with increasing the spark forming voltage. 2. The main crystal structure of the anodic oxide film was anatase type as analyzed with thin-film X-ray diffractometery. 3. Needle-like hydroxyapatite (HA) crystals were observed on anodic oxide films after hydrothermal treatment at $300^{\circ}C$ for 2 hours. The precipitation of HA crystals was accelerated with increasing the spark forming voltage. 4. The precipitation of the fine asperity-like HA crystals were observed after being immersed in Hanks' solution at $37^{\circ}C$. The precipitation of HA crystals was accelerated with increasing the spark forming voltage and the time of immersion in Hanks' solution. 5. The Ca/P ratio of the precipitated HA layer was equivalent to that of HA crystal as increasing the spark forming voltage and the time of immersion in Hanks' solution.