• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.250-255
• /
• 2023

This study applies various surface patterns to minimize material loss in construction equipment that is subject to severe wear due to sand, such as the wear-resistant steel plates of dump trucks or the teeth of excavators. The relationship between surface morphology and wear behavior is investigated using PLA+ polymer to observe the effect of the surface pattern. Five types of samples - smooth, concave, convex, wavy concave, and wavy convex designs - are created using a 3D printer. A wear experiment is conducted for a duration of 3 h using 6.5 kg of abrasive particles. The mass loss of the samples after the experiment is measured to assess the extent of wear. Additionally, the surface morphology of the samples before and after the experiment is analyzed using SEM and confocal microscopy. The study results reveal that the smooth design exhibits the highest wear loss, whereas the concave and wavy concave designs show relatively lower wear loss. The convex and wavy convex designs exhibit varying contact areas with the abrasive particles depending on the surface pattern, resulting in different levels of wear. Furthermore, a comparison between the experimental results and DEM simulations confirms the observed wear trends. This study reveals the relationship between wear damage according to surface pattern shape and is expected to be of substantial help in the analysis of wear and tear on agricultural and heavy equipment.

• Asian Journal of Turfgrass Science
• /
• v.25 no.1
• /
• pp.59-68
• /
• 2011

Research was initiated to investigate the effect of high water-absorbing polymer on turf grass quality of three major turfgrasses. A total of 12 treatment combinations were used in the study. Treatments were made with different rates of sand, soil organic amendment (SOA), and water-swelling polymer (WSP). Visual turf grass quality was evaluated in creeping bentgrass (Agrostis palustris Huds., CB), Kentucky bluegrass (Poa pratensis L., KB), and zoysiagrass (Zoysia japonica Steud., Zoy) grown under greenhouse conditions. Significant differences were observed among the treatments in CB, KB, and Zoy. Visual quality ratings varied with mixing rates of SOA and WSP, being maximum 5.6 in differences among them. At the end of study it ranged from 0.3 to 9.6 in CB, 0.3 to 4.0 in KB, and 0.9 to 5.8 in Zoy. Turfgrass quality pattern changed with time after seeding among treatments influenced by WSP rates. From this study, a proper rate of WSP is considered to be 5%, 5~10%, and 5% for CB, KB and Zoy, respectively. In general, overall treatment effect of WSP on turfgrass quality was highly associated with SOA 20% in three turtgrass species. When mixing sand with SOA and WSP for rootzone soil, a proper rate of SOA is considered to be 15 to 20% for CB and KB, while 20% for Zoy of warm-season grass. A further study would be required to investigate the effect of varied, gradual mixing rates of WSP on growth characteristics of turfgrasses grown on mixtures of sand, SOA, and WSP before a field application.

• Weed & Turfgrass Science
• /
• v.3 no.1
• /
• pp.19-28
• /
• 2014

Research was initiated in greenhouse to investigate effects of polymer, calcium, perlite and chitosan on the growth of Kentucky bluegrass (KB). A total of 24 treatment combinations were used in the study. Treatments were made of water-swelling polymer (WSP), calcium, perlite, and chitosan in soil organic amendment (SOA). Significant differences were observed in germination rate, turfgrass coverage, turfgrass density and top growth among treatments. Germination rate, density and plant height varied with time after seeding. A proper mix of WSP is considered to be lower than 3% for turfgrass coverage and density. Regarding survival capability and top growth, however, it was good under 6%. Overall KB growth was more influenced by calcium and perlite than chitosan. Calcium and perlite were the most effective elements for early survival capacity and turfgrass density, respectively. But no effect was found by chitosan. Top growth increased with three elements, being perlite > calcium > chitosan. The chitosan was effective in early germination, but there was no effect on top growth until 3 weeks, when compared with others. A further study is needed for investigating the effect of these materials on the growth characteristics in mixtures of sand and SOA before a field application.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.54-61
• /
• 2000

A method and results of classification of 4 types metallic wear debris were presented by using their color features. The color image of wear debris was used (or the initial data, and the color properties of the debris were specified by HSI color model. Particle was characterized by a set of statistical features derived from the distribution of HSI color model components. The initial feature set was optimized by a principal component analysis, and multidimensional scaling procedure was used for the definition of classification plane. It was found that five features, which include mean values of H and S, median S, skewness of distribution of S and I, allow to distinguish copper based alloys, red and dark iron oxides and steel particles. In this work, a method of probabilistic decision-making of class label assignment was proposed, which was based on the analysis of debris-coordinates distribution in the classification plane. The obtained results demonstrated a good availability for the automated wear particle analysis.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.7
• /
• pp.2111-2116
• /
• 2013

This paper reports substituent effects on the conformational changes in polyaniline (PAni) derivatives. PAni, poly-o-toluidine (POT), and poly-o-anisidine (POA) were formed by potentiodynamic electropolymerization in aqueous solution containing (+)-camphorsulfonic acid (CSA) as a dopant. UV-Vis spectroscopy and cyclic voltammetry measurements revealed that the methyl group showed a greater steric hindrance than the methoxy group. Further, the doping level decreased with increasing steric hindrance. The sign pattern of the circular dichroism (CD) bands for POA was opposite to that for PAni. However, no CD bands were observed in POT. The steric hindrance caused helical inversion, but at a high level of steric hindrance, the helical conformation could not be adopted, because of the reduced doping level. The reduced crystallinity was greatly affected by the decreased doping level. The steric effect influenced the polymer conformation and the doping level, thus determining the optical activity, morphology, and crystallinity of the PAni derivatives.

• Korean Journal of Clinical Pharmacy
• /
• v.1 no.1
• /
• pp.23-30
• /
• 1991

The sustained-release beads containing terbutaline sulfate (TBS) were prepared by rotogranulation method. The drug was dusted on the non-pareil seeds in a CF-granulator. The sustained-release beads were obtained by coating the active beads with ethylcellulose or $Eudragits^{(R)}$, using in any case the same granulator employed for active beads preparation. The release characteristics of sustained-release beads were examined in vitro by rotating basket method applied to $Bricanyl^{(R)}$ durules which is a sustained-release TBS matrix tablet. The release of terbutaline from the beads in vitro was first-order, and the release rate was dependent on both the coat weight ratio and membrane hydrophilicity. Both surfaces of the beads before and after dissolution were smooth. The drug release pattern from the beads could be thought the diffusion through the polymer membrane. The release rate and the surface of the beads stored for 3 years at room temperature were the same with those of the initial beads.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.10
• /
• pp.1644-1654
• /
• 2009

The concentration of dye uptake and the fastness improved when cotton and silk fabrics were treated with chitosan, a natural polymer. In this study, the effect of chitosan treatment was reviewed after the printing of cotton and silk fabrics padded with chitosan. When the change of physical and mechanical properties of printed fabrics was reviewed (as the concentration of chitosan increased) the thickness and weight increased a little, and the air permeability increased significantly than those untreated with chitosan. The dye uptake increased, accompanying a darker color shade, and the wash fastness increased 1/2-1 grade. The analysis results of enlarged images of printed patterns indicated that the width and area deformations were minimal as the concentration of chitosan increased when compared to untreated fabrics. Therefore, the dyeability and pattern quality were excellent after printing the chitosan-treated cotton and silk fabrics with cochineal dyestuff.

• Journal of Korean Institute of Industrial Engineers
• /
• v.19 no.3
• /
• pp.113-121
• /
• 1993

The pressure distribution between body and seat surface has been considered as one of the most important factors which affect seation comfort. The pattern of body pressure distribution has been an index of measuring comfort of an automobile seat. There has been numerous studies that measured the body pressure distribution. But, studies have many problems(pressure distortion, resolution, reliability, portability, usability, and shape fitness) in measuring the body pressure distribution. In this study, the new body pressure distribution measuring equipment has been developed by using the thin, flat, and polymer-film devices known as Force Sensing Resistors(FSRs) in order to solve those problems.

• Proceedings of the Korean Society for Applied Microbiology Conference
• /
• 1978.10a
• /
• pp.208.4-209
• /
• 1978

The Chitinase which hydrolyzes the chitin, $\beta-1,$ 4-polymer of N-acetyl glucosamine, was purified from the culture broth of Streptomyces sp. 115-5 strain. The homogeneity of enzyme was reveali by CM-Sephadex C-50 column chromatography and polyacrylamide gel electrophoresis. The purified enzyme hydrolyzed chitin and chitosan, but not cellulose. And with chitin as the substrate, a Km value of 3.6mg per ml and a Vmax of $100\mu$ mole per hr were found. The activation energy for the reaction was 3.66 Kcal per mole. The M. W. was estimated 56,000 daltons, and PI as 3.0. The chitinase was inhibited by the addition of glucose, glucuronic acid, sorbitol and xylose as product inhibitors and its inhibition pattern by glucose was estimated pure competitive type.

• Membrane Journal
• /
• v.15 no.2
• /
• pp.85-104
• /
• 2005

Recently, membrane can be prepared by two methods, phase inversion and electrospinning techniques. Phase inversion technique is a conventional but commercially preparation membrane. The most versatile of preparation in this technique is immersion of the cast film into nonsolvent bath, causing dense top layer with a finger-like pattern in the sub layer membrane. The membrane pore size getting from phase inversion is in the range of micro or submicrometer. As a result, it can be used as microfiltration and ultrafiltration applications. A new technique, electrospinning, is introduced for membrane preparation. Nonwoven nanofibrous mat or nanofibrous membrane is obtained. In this technique, electrostatic charge is introduced to the solution jet, causing a thin fiber with high surface area; hence it can be used in the applications where high surface area-to-volume or length-to-diameter ratios are required. Moreover, the pore size can be controlled by controlling the time of electrospinning. Hence, it can be used as a filter for filtering microparticles as well as nanoparticles.