• Journal of the Korean Home Economics Association
• /
• v.11 no.3
• /
• pp.276-284
• /
• 1973

An experiment, aimed at finding out the adhesive condition when adhesive non-woven fabrics for padding cloths are used for padding cloths of blouse, has been conducted. Materials used were three different kinds-scoured, sanforized, and permanent pressed- of combined fabrics of polyester and cotton. As for padding cloth material, mixed spinning nonwoven fabrics of polyster and viscose rayon have been used. Adhesive conditions were made each at $120^{\circ}C$, $140^{\circ}C$, $160^{\circ}C$ and $180^{\circ}C$, respectively, and adhesive time has been limited to 5, 10, 20, 30, 40 seconds each. External appearance as well as quality have been watched through washing experiment. In case of 12$0^{\circ}C$, all experimental materials were separated at the seventh washing and as for $140^{\circ}C$, all but the material which has been attached on scoured cloth for 40 seconds were separated. In case of 20 seconds only permanent pressed cloth and sanforized cloth were separated. At 30 and 40 seconds, the adhesive conditions have been maintained up to the seventh washing. In case of 5 seconds $180^{\circ}C$it was not turned yellow, but all were separated. In case of 10, 20, 30 and 40 seconds, at above temperature all were turned yellow in the adhesive process. Therefore, the adhesive power could be said strong enough, though it was not very practical. In this experiment, the lower the temperature of iron is, the longer time it has to be touched. At higher temperature however, relatively short time makesn it possible for adhesion and depending upon the finishing methode of cloth, there is slight difference in adhesive power. As a result, the best adhesive condition for all experimental materials is $160^{\circ}C$of iron temperature, and the time of adhesion is between 30 and 40 seconds.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.12
• /
• pp.2171-2178
• /
• 2016

Polyester cloth (PC) was selected as a prospective inexpensive substitute separator material for microbial fuel cells (MFCs). PC was compared with a traditional Nafion proton exchange membrane (PEM) as an MFC separator by analyzing its physical and electrochemical properties. A single layer of PC showed higher mass transfer (e.g., for $O_2/H^+/ions$) than the Nafion PEM; in the case of oxygen mass transfer coefficient ($k_o$), a rate of $50.0{\times}10^{-5} cm{\cdot}s^{-1}$ was observed compared with a rate of $20.8{\times}10^{-5}cm/s$ in the Nafion PEM. Increased numbers of PC layers were found to reduce the oxygen mass transfer coefficient. In addition, the diffusion coefficient of oxygen ($D_O$) for PC ($2.0-3.3{\times}10^{-6}cm^2/s$) was lower than that of the Nafion PEM ($3.8{\times}10^{-6}cm^2/s$). The PC was found to have a low ohmic resistance ($0.29-0.38{\Omega}$) in the MFC, which was similar to that of Nafion PEM ($0.31{\Omega}$); this resulted in comparable maximum power density and maximum current density in MFCs with PC and those with Nafion PEMs. Moreover, a higher average current generation was observed in MFCs with PC ($104.3{\pm}15.3A/m^3$) compared with MFCs with Nafion PEM ($100.4{\pm}17.7A/m^3$), as well as showing insignificant degradation of the PC surface, during 177 days of use in swine wastewater. These results suggest that PC separators could serve as a low-cost alternative to Nafion PEMs for construction of cost-effective MFCs.

• Journal of Sericultural and Entomological Science
• /
• v.18 no.1
• /
• pp.27-39
• /
• 1976

In this study several kinds of spun silk yarn-synthetic filament compounded yarn was manufactured, and several fabrics woven from above mentioned silk compound yarn for evaluation of serviceability as clothing materials. The following results were obtained: 1. Degumming agents are in the order of sodium silicate, sodium hydroxide, sodium carbornate, soap and water. 2. When the concentration of sodium hydroxide is exceeded 3%, degradation of floss silk property is resulted because of excessive dissolving out of silk protein. 3. Degumming effect is much improved by concentration of degumming agent and less by its treating time. 4. Simultaneous application of more the 2 kinds of degumming agent is desirable for improvement of floss silk. 5. Application of natural organic acid brings very good results in keeping original scooping and color of the silk. 6. Load and elongation it increased by compound with synthetic filament yarn. 7. Even the evenness of compound yarn is largely dependent on the quality of floss silk and extent of degumming, the C.V.% of silk compound yarn in the experiment was 8-12%. 8. Single bath dyeing technique was impossible for their cloth, and dyeing was performed in 2 bath system separately for silk and synthetic fiber. 9. Shrinkage ratio due to the dyeing of fabric was 23% in case of polyester and spun silk fabric. 10. The final woven cloth can be applicable to (a) Blouse in care of thin cloth (compound silk fabric) (b) Korean costume for women in case of thick cloth. (compound hand spun silk fabric)

• Journal of the Korean Society of Clothing and Textiles
• /
• v.40 no.5
• /
• pp.844-854
• /
• 2016

In order to understand the current state of production and pattern design of circular knitted jackets, this study selected 11 female clothing brands based from the "2012/2013 Korea Fashion Brand Yearbook" and interviewed the staff in charge of patterns at the companies. Polyester and polyurethane were found to be synthesized and used for the outshell of circular knitted jackets, alternatively natural fabric cotton or wool were synthesized with rayon. As for the structure of circular knitted materials, Ponte Di Roma knitting structure (a modified form of a double knit) was most often used. Surveying the use pattern and the parts for padding cloth, six responded that they used elastic padding cloth. As for circular knitted jackets with inner lining, elastic padding cloth was attached to all parts (front, back, side panel, and collar - except for sleeves) of the basic bodice pattern. Eight responded that they did not use a basic pattern when designing a pattern, which exceeds the majority. All respondents answered yes to the question on if there is any difference in designing a pattern for a woven jacket and a circular knitted jacket. It was found that they designed a pattern that considered shrinkage and elongation, which are the features of circular knitted fabric. Shrinkage and elongation were the features of a fabric material most considered when designing patterns for a circular knitted jacket.

• The Research Journal of the Costume Culture
• /
• v.15 no.6
• /
• pp.1053-1062
• /
• 2007

This study purposed to restructure representative traditional patterns formatively, manufacture actual cultural products with traditional dyeing technique using persimmon, and commercialize the results of the research. Traditionally in Korea, the dying of natural fiber such as cotton, flax and silk with persimmon was called Galmul dyeing, and clothes made through Galmul dyeing were called Galot. Galot was very useful because it is strong, does not pick up dirt easily, dries easily, and is cool in summer. In addition, cloth dyed with persimmon becomes stiff, so it does not need to be starched or ironed after washing. Moreover, it does not transmit heat under direct rays and is highly air-permeable, so it is cool and useful for standing the heat. In this study, we used traditional persimmon dyeing technique, printing traditional patterns fit for contemporary people's aesthetic sense not through dip-dying but through printing. When persimmon dyeing is used in expressing patterns, it produces not only visual effect but also embossing effect due to the characteristic of persimmon that makes printed patterns stiff, so we can obtain unique texture distinguished from other printing methods. We chose seven motive patterns, which were lotus pattern symbolizing eternal life, peony pattern symbolizing wealth and rank and prosperity, character Su(壽) pattern widely used as a symbol of health, bird and cloud pattern in the Goryeo Dynasty, Sahapyeoeuisohwa(四合如意小花) pattern printed on brocade in the Goryeo Dynasty, lattice pattern, cloth pattern on wall paintings from the Period of the Three Kingdoms. From each pattern chosen as a motive was extracted unit patterns and the original pattern was restored using Adobe Illustrator. Restored patterns were restructured to be applied to cultural products fit for contemporary formative sense. Fabrics used in dyeing were cotton, linen, ramie, silk, and polyester. Although the same persimmon dyeing was applied, we produced different feelings of patterns using various fabrics and in some cases gold and silver powder was added for the effect of gloss in addition to the embossing of patterns. Using printed fabrics we manufactured tea pads, place mats, cushions, wrapping cloth for gifts, wallet, lampshades.

• Journal of the Korean Society of Costume
• /
• v.57 no.2 s.111
• /
• pp.1-10
• /
• 2007

This study aims at the improvement of sewing function through understandings of dynamic property about the sewing methods and the thread material selection in knitwear. The tensile strength and shear of KES-FB and the Instron were measured for the analysis of the mechanical properties. The knit cloth was structured In the plain stitch, $1\times1$ rib stitch and $2\times1$ rib stitch with the combination of wool and cotton. With regard to the sewing method, intralooping and interlacing were applied. For thread materials, polyester, cotton, wool and silk were used. Since silk has the lowest extension and similar values regardless of its construction in intralooping, it is available knit apparel with uniform elastic recoverv. It also has small shearing resistance. It can be used in apparel which needs big mobility, but it causes rutting problem. Therefore, it is suitable to use intralooping. When the same sewing yarn and textile are use, it can lower shearing resistance and extension in intralooping, Since wool needs a lot of extension energy and it can be cut, intralooping is more suitable than interlacing in sewing of wool. In interlacing using polyester, extension and shearing resistance are high. Therefore, it is suitable for knit sewing with high massing. Silk is not suitable for interlacing since it can be rut. Even though knit materials are different, the RT values of polyester and cotton are similar in same construction. Therefore, they can be substituted each other considering resilience after sewing.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.8
• /
• pp.1177-1185
• /
• 2002

This study was to develop the sunshade hat which reduced stress from solar radiation and ultraviolet radiation (UV), in order to keep the farmer's health and to promote their work efficiency. The new sunshade hat with a large brim, special structure for ventilation, stability and portability was designed and tested with manikin heads outdoors. Two newly designed sunshade hats(A, B) and three existing hat were tested Sunshade hat A made of double fabric with aluminum coating-nylon and black cotton cloth with a polyester mix(T/C) was the most protective from solar radiation. Sunshade hat B with larger brim was the most protective from ultraviolet radiation, even though it was made of aluminum coating-nylon single fabric.

• Journal of Sericultural and Entomological Science
• /
• v.25 no.2
• /
• pp.51-57
• /
• 1984

This studies have been carried out to find anticrease finishing method other than urea formaldehyde polymerization method which the author had done it with his former report. Acrylic amide polymerization method with water solubility controlling device was developed in this parer and the obtained results are as followings. 1. Poor anticrease silk textile could improve as much as 25% than original fabric. 2. Light density with high twisted silk textiles may improve a few per cent increase of anticrease, because they held good anticrease nature as well as polyester fabric. 3. There was no significant stiffness change after such finish. 4. This finish is recommended to carry after dyeing process either yarn dye or cloth dyeing. 5. The finished textile with this method is recommended to wash with dry cleanning method.

• Textile Coloration and Finishing
• /
• v.12 no.3
• /
• pp.192-198
• /
• 2000

Influence of the fluorescent whitening agent(FWA)'s adsorption on the whiteness of cotton and on the color change of the dyed fabrics was investigated by repeating wash cycles. Cotton 100% and cotton60/polyester40 blended fabrics were dyed pink, blue and yellow, and cyanuric chloride diamino stilbene(CC/DAS) and distyryl bisphenyl(DSBP) were used for the FWA with laundry detergents. Fabrics were washed at $20^\circ{C}$ with Terg-o-tometer. The FWA adsorption amount was measured by the absorption intensity for the pyridine-water extracted solution. The FWA adsorption increased on the cotton fabric with the wash cycles. Though adsorption of CC/DAS continuously increased up to the 20th cycle, that of DSBP increased sharply before the 10th cycle and reached an equilibrium. The whiteness of the fabrics dried in the shade was greater than that dried under the sunlight through window glass. The color change of dyed fabrics was increased by the number of wash cycles. Pink changed more greatly than blue, yellow or grey cloth. The color change(\Delta{E)}$ of dyed fabric washed repeatedly up to the 20th cycle with the detergent without FWA was less than 1. It is recommended to wash pale colored fabric with the detergent free of FWA.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.13 no.3 s.31
• /
• pp.259-267
• /
• 1989

In this paper, the fabric specimen undergoes repeated laundering under given condition. After this cyclic laundering was applied, the crease recoveries of the specimen were measured using shirley crease revovery tester in order to evaluate the effect of factors at given condition during crease deformation. 5 samples of grey plain cloth were desized, alkali-scoured, bleached, whased with water, and air-dried. All tests were made on samples preconditioned to $65\%\;RH\;and\;20^{\circ}C$. The experimental results were analysed statistically to relate crease recoveries and the properties of smaples, recovery periods (time) of crease. Furthermore, the crease recoveries of core-spun yarn woven fabrics were discussed in comparison with those values for $100\%$ combed cotton yarn woven fabric and $65\%$ polyester $35\%$ carded cotton blended yarn woven fabric. The results obtained are as follows; 1. Regardless of materials, remarkable decrease are observed in crease recoveries about 1-5 cycles of the repeated laundering, but slack decrease are observed in crease recoveries after 5 cycle of the re-peated laundering. 2. Crease recoveries ($\alpha$) of core-spun yarn woven fabrics are relate to recovery periods (t) of crease as follows; log$\alpha$=0.01415 log t+2.1168 ($r^2=0.94$) 3. Core-spun yarn woven fabrics were superior to $100\%$ combed cotton yarn woven fabrics and $65\%$ polyester $35\%$ carded cotton blended yarn woven fabric in crease recoveries. 4. Crease recoveries ($\alpha$) of core-spun yarn woven fabrics are relate to cover factor (CF), thickness (T) at pressure 0.5 $gf/cm^2$, weight (W) as follows; log$\alpha$=-0.3482 log CF-0.4924 log T-0.4727 W+2.4243 ($r^2=0.88$) 5. Crease recoveries ($\alpha$) of core-spun yarn woven fabrics are relate to 2HB/B, 2HB/W, $\sqrt[3]{B/W}$, WC/T which are concerning to formation of weared clothes and bending Iran formation behavior as follows: log $\alpha$=0.0091 2HB/B+0.4667 2HB/W+0.0185 $\sqrt[3]{B/W}$+0.0114 WC/T+1.8433 ($r^2=0.86$)