• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1028-1031
• /
• 2009

High quality poly-SiGe thin films were prepared on 6-inch substrates using Reactive-thermal CVD with $Si_2H_6$ and $GeF_4$ around at $500^{\circ}C$ directly. Its thickness uniformity was ~ 3% on the entire substrate area. N-channel mobility of ~30 nm thick bottom-gate TFTs exceeded 20 $cm^2$/Vs without any further crystallization.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.2
• /
• pp.297-305
• /
• 2000

It is observed that the initial properties and degradation characteristics on plasma of n/p-MOSFET with polycide and poly-Si as different gate materials under F-N stress and hot electron stress are affected by metal AR(Antenna Ratio) during plasma process. Compared to that of MOS devices with poly-Si gate material, reliability properties on plasma of MOS devices with polycide gate material are improved. This can be explained by that fluorine of tungsten polycide process diffuses through poly-Si into gate oxide and results in additional oxide thickness. The fact that MOS devices with polycide gate material can reduce damages of plasma process shows possibility that polycide gate material can be used as gate material for next generation MOS devices.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.718-722
• /
• 2006

The dependence of n-channel 2 shot SLS poly-Si TFT characteristics on the DOS (density of states) parameters was investigated by using a device simulation. Device performances were most sensitive to the DOS of poly-Si/gate insulator (GI) interface and poly-Si active layer. Deep level states at the poly-Si/GI interfaces strongly affect the subthreshold slope.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.107-116
• /
• 1994

In this paper, The electrical properties of MOS capacitors and transistoras with gate of in-situ doped amorphous Si and poly Si doped by POCI$_3$. Under constant current F-N stress, MOS capacitors with in-situ doped amorphous Si gate have shown the best resistance to degradation in reliabilty properties such as increase of leakage current, shift of gate voltage (V$_{g}$). shift of flat band voltage (V$_{fb}$) and charge to breakdown(Q$_{bd}$). Also, MOSFETs with in-situ doped amorphous Si gate have shown to have less degradation in transistor properties such as threshold voltage, transconductance and drain current. These improvements observed in MOS devices with in-situ doped amorphous Si gate is attributed to less local thinning spots at the gate/SiO$_2$ interface, caused by the large grain size and the smoothness of the surface at the gate/SiO$_2$ interface.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.3
• /
• pp.261-264
• /
• 2005

The 90 nm gate pattern technology have been virtualized by employing the hard mask and the planarization of fate poly silicon. We fabricated 70nm poly-Si on $200 nm-SiO_2/p-Si(100)$ substrates using low pressure chemical vapor deposition (LPCVD) to investigate roughness evolution by varying rapid annealing temperatures. The samples were annealed at the temperatures of $700^{\circ}C\~1100^{\circ}C$ for 40 seconds with a rapid thermal annealer. The surface image and the surface roughness were measured by a field emission scanning electron microscopy (FESEM) and an atomic force microscopy (AFM), respectively. The poly silicon surface became more rough as temperature increased due to surface agglomeration. The optimum conditions of poly silicon planarization were achieved by annealed at $700^{\circ}C$ for 40 seconds.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.489-492
• /
• 1999

The effects of alternate bias stress on p-channel poly-Si TPT's has been systematically investigated. It has been shown that the application of alternate bias stress affects device degradation for the negative bias stress as well as device improvement for the positive bias stress. This effects have been related to the hot carrier injection into the gate oxide rather than the generation of defect states within the poly-Si/SiO$_2$ under bias stress.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.2
• /
• pp.7-11
• /
• 2000

a-Si:H and poly-Si TFT(thin film transistor) characteristics were investigated using an inverted staggered type TFT. The TFT an as-grown a-Si:H exhibited a low field effect mobility, transconductance, and high gate threshold voltage. The poly-Si films were achieved by using an isothermal and RTA treatment for glow discharge deposited a-Si:H films. The a-Si:H films were cystallized at the various temperature from 600$^{\circ}C$ to 1000$^{\circ}C$. As anneal temperature was elevated, the TFT exhibited increased g$\sub$m/ and reduced V$\sub$ds/. V$\sub$T/. The poly-Si grain boundary passivation with grain boundary trap types and activation energies as a function of anneal temperature. The poly-si TFT showed an improved I$\sub$nm//I$\sub$off/ ratio of 10$\^$6/, reduced gate threshold voltage, and increased field effect mobility by three orders.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.129-130
• /
• 2008

Polycrystalline silicon (poly-Si) Schottky barrier thin film transistors (SB-TFT) are fabricated by erbium silicided source/drain for n-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method. The fabricated poly-Si SB-TFTs have a large on/off current ratio with a low leakage current. Moreover, the electrical characteristics of poly-Si SB TFTs are significantly improved by the additional forming gas annealing in 2 % $H_2/N_2$, because the interface trap states at the poly-Si grain boundaries and at the gate oxide/poly-Si channel decreased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.9
• /
• pp.683-686
• /
• 1998

Hot carrier effects as a function of bias stress time and bias stress consitions were syste-matically investigated in p-channel poly-Si TFT s fabricated on the quartz substrate. The device degradation was observed for the negative bias stress, while improvement of electrical characteristic except for subthreshold slope was observed for the positive bias stress. It was found that these results were related to the hot-carrier injection into the gate oxide and interface states at the poly-Si/$SiO_2$interface rather than defects states generation within the poly-Si active layer under bias stress.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.545-545
• /
• 2008

Poly-Si is an essential material for floating gate in NAND Flash memory. To fabricate this material within region of floating gate, chemical mechanical polishing (CMP) is commonly used process for manufacturing NAND flash memory. We use colloidal silica abrasive with alkaline agent, polymeric additive and organic surfactant to obtain high Poly-Si to SiO2 film selectivity and reduce surface defect in Poly-Si CMP. We already studied about the effects of alkaline agent and polymeric additive. But the effect of organic surfactant in Poly-Si CMP is not clearly defined. So we will examine the function of organic surfactant in Poly-Si CMP with concentration separation test. We expect that surface roughness will be improved with the addition of organic surfactant as the case of wafering CMP. Poly-Si wafer are deposited by low pressure chemical vapor deposition (LPCVD) and oxide film are prepared by the method of plasma-enhanced tetra ethyl ortho silicate (PETEOS). The polishing test will be performed by a Strasbaugh 6EC polisher with an IC1000/Suba IV stacked pad and the pad will be conditioned by ex situ diamond disk. And the thickness difference of wafer between before and after polishing test will be measured by Ellipsometer and Nanospec. The roughness of Poly-Si film will be analyzed by atomic force microscope.