• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.5
• /
• pp.609-616
• /
• 2019

When the fouling of a vessel occurs, its resistance at sea increases and there is a corresponding increase in fuel consumption. The maintenance cost of the vessel also increases because it is time-consuming to remove the fouling. To solve this problem and minimize environmental contamination of sea-water, there have been recent developments in anti-fouling paints as self-polishing copolymers that not include toxic elements such as tin. When these conventional techniques are applied to vessels, polishing is promoted during the operation whereby friction or vibration with seawater occurs. This leads to enhanced anti-fouling performance. However, when fouling is intensified such as during an anchorage, there is no flow of seawater and polishing is suppressed. This leads to a deterioration of the performance of anti-fouling. To solve these problems, we developed a system that induces vibration in a vessel during anchorage. As such, the deterioration of polishing due to insuf icient flow of seawater is inhibited. The reliability of the ultrasonic antifouling system was evaluated by calculating its repeatability. The removal efficiency of fouling of the proposed system was qualitatively evaluated using test specimens. The test revealed that the value of the coefficient of variation for the reproducibility of the frequency and amplitude was 0.2 % and 4.0 % on average. The degree of fouling of the specimens was the highest at 73.3 g in the No.5 sepcimen. Moreover, efficiency of fouling removal was 93.2 % on average compared to the specimens without the proposed system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.557-561
• /
• 2001

Chemical mechanical polishing (CMP) process has been widely used to planarize dielectric layers, which can be applied to the integraded circuits for sub-micron technology. Despite the increased use of CMP process, it is difficult to accomplish the global planarization of in the defect-free inter-level dielectrics (ILD). Especially, defects such as micro-scratch lead to severe circuit failure which affect yield. CMP slurries can contain particles exceeding 1㎛ in size, which could cause micro-scratch on the wafer surface. The large particles in these slurries may be caused by particles agglomeration in slurry supply line. To reduce these defects, slurry filtration method has been recommended in oxide CMP. In this work, we have studied the effects of filtration and the defect trend as a function of polished wafer count using various filters in inter-metal dielectrics(IMD)-CMP process. The filter installation in CMP polisher could reduce defects after IMD-CMP process. As a result of micro-scratch formation, it is shown that slurry filter plays an important role in determining consumable pad lifetime. The filter lifetime is dominated by the defects. We have concluded that slurry filter lifetime is fixed by the degree of generating defects.

• Journal of Welding and Joining
• /
• v.19 no.2
• /
• pp.191-199
• /
• 2001

The oxidation and recrystallization behaviors of Ni-base single crystal superalloy, CMSX-2 were investigated to determine the condition of the preparation for transient liquid phase (TLP) bonding operations. The faying surfaces of CMSX-2 were worked by the shot peening, fine cutting and mechanical polishing treatments and the degree of working of treated surfaces was evaluated by the hardness test and X-ray diffraction method CMSX-2 was heat-treated at 1,173∼1.589k for 3.6ks in vacuum of 4mPa. The mechanically polished surface was slightly oxidized after heat treatment even in the vacuum atmosphere of 4mPa. The thickness of an oxide film increased with increasing the heating temperature and the surface roughness of the faying surface. Recrystallization occurred at the surface after heat treatment at above 1,423K when the hardness was increased more than Hv600 by the shot peening treatment while the mechanically polished or fine cut surfaces didn't recrystallized. Based on these results, it was clearfied that the mechanically polishing with fine abrasive grit could be used for the preparation of faying surface of CMSX-2 before bonding operation.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2003.10a
• /
• pp.46-50
• /
• 2003

In order to develop a new variety of rice that adapts to the climate of Aomori prefecture and possesses characteristics suitable for production of high quality Japanese sake, artificial cross experiments were executed between Yamadanishiki, which is widely used nationwide as an authentic variety of rice for sake production, and Hanafubuki, which was peviously developed by Aomori prefecture. An excellent hybrid, named Hanaomoi, was selected and fixed by a series of selection experiments and systematic cultivation. Unpolished Hanaomoi rice contained less amount of protein than Yamadanishiki and Hanafubuki. Unpolished rice of Hanaomoi was harder than Yamadanishiri and Hanafubuki, therefore polishing treatment was done in high yield and one could obtain a high degree of polish on the rice(namely 40% polishing). These features are advantageous to production of high quality of sake.Test brewing using 40% polished Hanaomoi gave rise to a characteristic sake that contained a slightly higher amount of alcohol and flavor components than Yamadanishiki and Hanafubuki. Sensory tests concluded that sake from Hanaomoi was as superior as the one from authentic Yamadanishiki. Hanaomoi is a promising variety of rice suitable for production of a high quality sake exclusive to Aomori prefecture.

• Journal of Periodontal and Implant Science
• /
• v.48 no.6
• /
• pp.373-382
• /
• 2018

Purpose: The aim of this study was to evaluate the effects of various prophylactic treatments of titanium implants on bacterial biofilm formation, correlating surface modifications with the biofilms produced by Pseudomonas aeruginosa PAO1, Staphylococcus aureus, and bacteria isolated from saliva. Methods: Pure titanium disks were treated with various prophylactic procedures, and atomic force microscopy (AFM) was used to determine the degree to which surface roughness was modified. To evaluate antibiofilm activity, we used P. aeruginosa PAO1, S. aureus, and saliva-isolated Streptococcus spp., Bacteroides fragilis, and Staphylococcus epidermidis. Results: AFM showed that the surface roughness increased after using the air-polishing device and ultrasonic scaler, while a significant reduction was observed after using a curette or polishing with Detartrine ZTM (DZ) abrasive paste. In addition, we only observed a significant (P<0.01) reduction in biofilm formation on the DZ-treated implant surfaces. Conclusion: In this study, both AFM and antibiofilm analyses indicated that using DZ abrasive paste could be considered as the prophylactic procedure of choice for managing peri-implant lesions and for therapy-resistant cases of periodontitis.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.40 no.3
• /
• pp.149-158
• /
• 2024

Purpose: This study aims to investigate the effects of provisional restoration fabrication methods and surface polishing on surface roughness and microbial adhesion through in vitro experiments. Materials and Methods: 120 cylindrical provisional restoration resin blocks (10 × 10 × 2.5 mm) were manufactured according to four fabrication methods, and 30 specimens were assigned to each group. Afterwards, they were divided into non-polishing group, #400 grit SiC polishing group, and #800 grit SiC polishing group and polished to a 10 × 10 × 2 mm specimen size (n = 10). The surface roughness Ra and Ry of the specimen was measured using a Surface Roughness Tester. Three specimens were extracted from each group and were coated with artificial saliva, and then Streptococcus mutans were cultured on the specimens at 37℃ for 4 hours. The cultured specimens were fixed to fixatives and photographed using a scanning electron microscope. For statistical analysis, the two way of ANOVA was performed for surface roughness Ra and Ry, respectively, and the surface roughness was tested post-mortem with a Scheffe test. Results: The fabrication method and the degree of surface polishing of the provisional restorations had a significant effect on both surface roughness Ra and Ry, and had an interaction effect. There was no significant difference in Ra and Ry values in all polishing groups in DLP and LCD groups. Conclusion: The fabrication method and surface polishing of the provisional restoration had a significant effect on surface roughness and showed different adhesion patterns for S. mutans adhesion.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.4 no.1
• /
• pp.97-100
• /
• 1975

Degree of polished rice so called 70 percentage of polished rice sold at the 19 places of rice dealer's store in Gwang - Ju city were surveyed through the New M.G.color reaction reagent, from 24th to 30th of January, 1975. The results were as follows ; 1. Nearly the 70 percentage polished rice sold at the rice dealer's store showed some differences in the degree of polishing of rice, with respect to color reaction in comparison with standard 70 percentage polished rice. 2. There have been no rice which are over excessive 70 percentage polished rice. 3. The place were more than 90 percentage of 70percentage polished rice amount, were 3 places in the 19 places rice dealer's store and 50 percentage of below 70 percentage polished rice amount were 8 places in the 19 places.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.2
• /
• pp.401-414
• /
• 1996

The purpose of this study was to compare the marginal leakage of resin liner which was used as a liner to amalgam restoration. Control group composed of no liner group, copalite group and experimental group composed of All-bond 2, Vitrebond, Superbond D-liner applied groups were evaluated. Cl.V preparation with a size of $3{\times}2{\times}1.5mm$ on 70 extracted primary molars were made and applied appropriate liners for each groups. After amalgam filling and polishing, polished specimens underwent temperature changed from $5^{\circ}C\;to\;55^{\circ}C$ a thousand times. After thermocycling, specimens were placed in 2% methylene blue dye solution for 72 hours in an incubator set at $37^{\circ}C$. The teeth were sectioned buccolingually and the degree of dye penetration was observed with a spectroscopy. (${\times}30$) The following results were obtained. 1. Vitrebond, All-bond 2, Superbond D-liner group exhibited a statistically significant lower degree of dye penetration than no liner and copalite group. (Kruskal-Wallis analysis, P<0.05) 2. No liner group and copalite group exhibited a similar degree of dye penetration. (Mann-Whitney analysis, P>0.05) 3. All-bond 2 group exhibited a statistically significant lower degree of dye penetration than Vitrebond group, (Mann-Whitney analysis, P<0.05) Superbond D-liner group also exhibited a lower degree of dye penetration than Vitrebond group but was statistically insignificant. (Mann-Whitney analysis, P>0.05)

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.3
• /
• pp.52-57
• /
• 2004

Many kinds of gases, such as erosion gas, dilution gas, and toxic gas have been used in manufacturing process of LCD at semiconductor. In order to increase accumulation rate of manufacturing process, high degree of purity in these gases and minimized metalllic dust are required. All wetted stainless steel surface must be 316L electro-polished with $0254{\mu}m$ in average. Based on the AES analysis, Cr/Fe 11 and $Cr_2O_3$ thickness $25{\AA}$ are measured Molybdenum and silicon contaminants which is characteristic of stainless steel and oxygen were found on the surface.

• The Journal of Engineering Geology
• /
• v.8 no.3
• /
• pp.235-245
• /
• 1998

Adquate friction resistance is needed to prevent pavement slipperiness and to allow vehicles to stop in a reasonable distance. Performance of the aggregates is reduced over time by wear and polishing as a consequence of vehicular traffic. In this research, the objective was to develop a laboratory method to test Indiana gravel aggregates to predict field performance, and determine causes for the range of values amang gravel aggregates. The assessment of gravel sources was primarily on the basis of individual rock types and those proportions comprising the gravel. Polish and friction values were determined in the laboratory with the British Wheel and Pendulum. The gravels of this study were composed primarily of carbonate aggregates that showed considerable variability in polishing thresholds. Igneous and metamorphic constituents polished to a lesser degree and are expected to improve overall aggregate performance. Estimates of the IFV (Initial Friction Value) and PV (Polished Value) for crushed gravel samples can be made based on the percentage of rock types present in the sample. A weighted average is used to make this calculation.