• Korean Journal of Applied Biomechanics
• /
• v.14 no.1
• /
• pp.27-40
• /
• 2004

The purpose of this study was to provide basic data for improving athletic performances by analyzing the kinematic variables of the Double Backward Somersault on the Parallel Bars through the 3D motion analysis. The subjects in this study were 5 male gymnasts who were ranked as national athletes. The results are as follows. 1. A total time(Mean Time) of performance showed $2.72{\pm}0.82\;sec$. and flight time to landing after releasing was 0.87sec.(mean). In order to perform better stable flying movement, the flight time should be increased. 2. In the change of velocity of the center of mass, when the increasing ascension velocity of the upper point was high, the position in the top point was high on releasing. 3. In the position variable of the center of mass, the mean of upper-bottom position in horizontal posture was $242.1{\pm}6.5cm$, $232.8{\pm}6.4cm$ in releasing, and $265.0{\pm}5.6cm$ in the highest point. This result is explained that the position of center of mass can be raised by using elastic power when wrist raised the bar in the releasing movement. 4. The angle of shoulder joint was $271.1{\pm}14.0$. Such a big angle influences a negative effect on the releasing velocity, because trunk is not a position in the enough vertical direction. 5. The ankle of hip joint in hand-standing was $191.1{\pm}5.9$, $118.8{\pm}5.3$ in releasing, and $122.3{\pm}5.3$ in taking on. Therefore, the result suggests that trunk should be straightly raised in taking on.

• The Bulletin of The Korean Astronomical Society
• /
• v.20
• /
• pp.32.2-33
• /
• 1995

• The Bulletin of The Korean Astronomical Society
• /
• v.19
• /
• pp.28-28
• /
• 1994

• Journal of Korean Neurosurgical Society
• /
• v.54 no.1
• /
• pp.25-29
• /
• 2013

Objective : To clarify the landmark for deciding the entry point for C1 lateral mass screws via the posterior arch by using 3-dimensional (3D) computed images. Methods : Resnick insisted that the C1 posterior arch could be divided into pure posterior and lateral lamina (C1 pedicle). Authors studied where this transition point (TP) is located between the posterior lamina and the C1 pedicle and how it can be recognized. The 3D computed images of 86 cadaver C1s (M : F=45 : 41) were used in this study. Results : The superior ridge of the C1 posterior arch had 2 types of orientation. One was in the vertical direction in the C1 posterior lamina and the other was in the horizontal direction in the C1 pedicle. The TP was located at the border between the 2 areas, the same site as the posterior end of the groove of the vertebral artery. On posterior-anterior projection, the posterior arch was sharpened abruptly at TP. We were unable to identify the TP in 6.4% of specimens due to complete or partial osseous bridges. A total of 93.8% of the TP were located between the most enlarged point of the spinal canal and the medial wall of the vertebral artery. Conclusion : The anatomic entry zone of C1 lateral laminar screws was clarified and identified based on the TP by using preoperative 3D computed images.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.6
• /
• pp.968-979
• /
• 2009

The purpose of this study was to examine the relationship between the willingness to adopt mass customization and four proposed characteristics: organizational, individual, technological, and environmental. Retail managers' and consumers' point of view was separately examined to distinguish their characteristics and willingness to adopt mass customization. The sample of this study consisted of 66 managers and 274 consumers in their twenties. The researcher obtained seven findings from the hypotheses testing. The determinants of mass customization adoption were managers' technology and environmental characteristics, and consumers' individual, technology, and environmental characteristics. The most influential variables for the willingness to adopt mass customization were technology characteristics and retailer's customer relationship management process, where customer satisfaction and customer relationships are the top priority in an organization.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.32-40
• /
• 2018

In order to avoid excessive vibration, it is required to carry out a vibration analysis of heat-exchanger/nuclear-reactor at the design stage. Information of eigen-frequency in the vibration problem is required to evaluate safety of heat-exchange/nuclear reactor. This paper describes a numerical method, Galerkin's method, to solve the eigenvalue problem occurred in a cantilever beam. The beam is restrained with added mass and spring at the free end or a node point of a mode shape. The numerical results of eigen-frequency were compared with simple analytical and experimental results given by simple approach and simple test, respectively. It is found that Galerkin's method is applicable to estimate the eigen-frequency of the cantilever beam. The frequencies become lower with increasing the added mass and the frequencies increase with the spring force. It is shown the heavy added mass has a role of support on the flexible tube. The eigen-frequency of the first mode, for the system with the added mass mounted at the free end, can be calculated by the approximate analytical method existing with more or less accuracy.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.7
• /
• pp.864-872
• /
• 2020

In accordance with the sulfur regulations of the International Maritime Organization (IMO), very low sulfur fuel oil (VLSFO) shows various production-dependent physico-chemical properties. This study aims to use as basic data for oil spill response according to study of physico-chemical characteristics of VLSFO and mixed fuel oil of VLSFO-HSFO. The mixed fuel oil was prepared by mixing 25, 50, 75 mass% of HSFO with VLSFO containing 0.46 and 0.36 mass% of sulfur. The physico-chemical properties such as the kinematic viscosity, pour point and distribution of Saturates, Aromatics, Resins, and Asphaltenes (SARA) were studied in the laboratory. As mixed of 75 mass% of HSFO with high the kinematic viscosity and low pour point in VLSFO, the kinematic viscosity of the mixed fuel oil increased to 350.2 %, and VLSFO with pour point of 23℃ and -11℃ lowered or raised to -3℃ and -6℃ respectively. As HSFO was mixed in VLSFO with a small Asphaltenes distribution, the Saturates distribution decreased to 68.8% and Asphaltenes distribution increased to 1,417 % dramatically.

• Ceramist
• /
• v.21 no.3
• /
• pp.249-269
• /
• 2018

In conventional MALDI-TOF mass spectrometry, analyte molecules are known to be ionized by mixing with organic matrix molecules. As the organic matrix molecules are made into small fragments, they generate unreproducible mass peaks such that MALDI-TOF mass spectrometry is nearly impossible in the low mass-to-charge (m/z) range (< 1000). Additionally, the dried sample mixed with matrix were made as inhomogeneous crystal on metal plate. When the laser radiation was made on the sample crystal, the amount of generated sample ion was observed to be quite different according to the radiation point. Therefore, the quantitative analysis was very difficult even for the sample spots at the same concentration for the conventional MALDI-TOF mass spectrometry. In this work, we present laser desorption/ionization (LDI) mass spectrometry based on solid-matrices for the quantitative analysis of small molecules in the low m/z range by using MALDI-TOF mass spectrometry: (1) Carbon based nanostructures; (2) Semiconductor based nanomaterials; (3) Metal based nanostructures.

• International Journal of Contents
• /
• v.10 no.3
• /
• pp.84-89
• /
• 2014

The mass-spring model has been typically employed in physical-based simulators for clothes or patches. The mass-spring model frequently utilizes equal mass and the gravity factor. The model structure of masses supports a shape applicable to fishing nets. Therefore, to create a simulation model of a fishing net, we consider the mass-spring model and adopt the tidal-current and buoyancy effects in underwater environments. These additional factors lead to a more realistic visualization of fishing-net simulations. In this paper, we propose a new mass-spring model for a fishing-net and a method to simplify the calculation equations for a real-time simulation of a fishing-net model. Our 3D mass-spring model presents a mesh-structure similar to a typical mass-spring model except that each intersection point can have different masses. The motion of each mass is calculated periodically considering additional dynamics. To reduce the calculation time, we attempt to simplify the mathematical equations that include the effect of the tidal-current and buoyancy. Through this research, we expect to achieve a real-time and realistic simulation for the fishing net.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.1
• /
• pp.22-25
• /
• 1979

The mechanical floating-mass which is analogous to an electrical floating- capacitance may not come across because a mass element in a mechanical network must be attracted to rho ground which is the reference point. In this study the mechanical floating-mass is fonstructed by employing two simple support levers, one link, one mass, and four frictionless hearings. It also shows that the mechanical device can be used to give various equivalent masses by altering the arm ratio of the levers.