• Nuclear Engineering and Technology
• /
• v.46 no.4
• /
• pp.547-556
• /
• 2014

Korea expects a shortage in storage capacity for spent fuels at reactor sites. Therefore, a need for more metal and/or concrete casks for storage systems is anticipated for either the reactor site or away from the reactor for interim storage. For the purpose of interim storage and transportation, a dual purpose metal cask that can load 21 spent fuel assemblies is being developed by Korea Radioactive Waste Management Corporation (KRMC) in Korea. At first the gamma and neutron flux for the design basis fuel were determined assuming in-core environment (the temperature, pressure, etc. of the moderator, boron, cladding, $UO_2$ pellets) in which the design basis fuel is loaded, as input data. The evaluation simulated burnup up to 45,000 MWD/MTU and decay during ten years of cooling using the SAS2H/OGIGEN-S module of the SCALE5.1 system. The results from the source term evaluation were used as input data for the final shielding evaluation utilizing the MCNP Code, which yielded the effective dose rate. The design of the cask is based on the safety requirements for normal storage conditions under 10 CFR Part 72. A radiation shielding analysis of the metal storage cask optimized for loading 21 design basis fuels was performed for two cases; one for a single cask and the other for a $2{\times}10$ cask array. For the single cask, dose rates at the external surface of the metal cask, 1m and 2m away from the cask surface, were evaluated. For the $2{\times}10$ cask array, dose rates at the center point of the array and at the center of the casks' height were evaluated. The results of the shielding analysis for the single cask show that dose rates were considerably higher at the lower side (from the bottom of the cask to the bottom of the neutron shielding) of the cask, at over 2mSv/hr at the external surface of the cask. However, this is not considered to be a significant issue since additional shielding will be installed at the storage facility. The shielding analysis results for the $2{\times}10$ cask array showed exponential decrease with distance off the sources. The controlled area boundary was calculated to be approximately 280m from the array, with a dose rate of 25mrem/yr. Actual dose rates within the controlled area boundary will be lower than 25mrem/yr, due to the decay of radioactivity of spent fuel in storage.

• Fire Science and Engineering
• /
• v.25 no.6
• /
• pp.89-97
• /
• 2011

This study is for evaluating the fire resistance performance (1~2 h) of the RC Structure void slab using the Lightweight Hollow Sphere, which can reduce the unnecessary dynamic part of removing the central concrete. For this experiment, we set up depth of concrete cover, live load, and span length as the factors. The result comes out with all the slabs under those conditions can ensure the goal fire resistance performance (120 min). And among these factors, the resisting capability changes more sensitively with the live load rather than the thickness of cover. And the shorter span length could assure the better the fire resistance performance. The result observing the character in high temperature of the Lightweight Hollow Sphere which does not used as existing RC structure slab, a delay section in temperature change is occurred due to the Glass Transition in $100^{\circ}C$. And heat transfer by conduction does not occur at lightweight hollow sphere because the polystyrene in EPS (Expanded Polystyrene) melts point in $185^{\circ}C$. Therefore temperature at lightweight hollow sphere is lower than the concrete and rebar.

• Journal of Pharmaceutical Investigation
• /
• v.30 no.3
• /
• pp.173-178
• /
• 2000

The purpose of this work is to develop a transurethral suppository containing prostaglandin $E_1\;(PGE_1)$, which stabilizes the drug, gives no irritation to physiological body and enhances the erectile response of $PGE_1.\;PGE_1$ transurethral suppositories were prepared with various amounts of compositions such as saturated polyglycolysed glyceride $(Suppocire^{\circledR}\;AP,\;SAP)$, polyoxyethylene hydrogenated castor oil (HCO-50) and ethanol. The melting points, viscosities and $PGE_1$ release of the suppositories were investigated. Ocular irritation test was carried out after application of $PGE_1$ suppository to rabbit's eye. The intracavernous pressure (ICP), penile length and duration of erectile response were determined after transurethral administration of $PGE_1$ suppository and compared with those after intracavernosal injection of $PGE_1$ solution to cats. HCO-50 hardly affected the melting points and viscosities of $PGE_1$ suppositories. Additionally, $PGE_1$ transurethral suppositories, whose melting point ranges was $34-35^{\circ}C$, was speedily melted in physiological body. HCO-50 significantly decreased the dissolution rates of $PGE_1$ from the suppositories. Dissolution mechanism analysis showed the release of $PGE_1$ was proportional to the square root of time, indicating that $PGE_1$ might be released from the suppositories by Fickian diffusion. The release rate of $PGE_1$ from $PGE_1$ suppository [PGE1/SAP/HCO-50/ethanol (1/94.5/2.5/2%)] was about 80% within 2 h. This $PGE_1$ suppository gave no significant irritation to the ocular tissue, expecting that it gave no irritation to the urethral tissue less sensive than ocular tissue. Furthermore, $PGE_1$ in this suppository was stable at $4^{\circ}C$ for 2 years. This suppository increased the ICP and penile erection similar to those of injectable $PGE_1$ solution. However, it gave 2.5-fold increased duration of erectile response than injectable $PGE_1$ solution. Our results suggested that it gave more effective erectile response than injectable $PGE_1$ solution in cats. It is concluded that this $PGE_1$ suppository with good safety, excellent stability and enhanced erectile response, could be a more effective and convenient transurethal delivery system of $PGE_1$.

• The Journal of the Korea Contents Association
• /
• v.19 no.12
• /
• pp.28-37
• /
• 2019

It is apparently clear that K-pop has been expanding its influence overseas, with its high growth rate. As a result, attempts have been made to analyze the characteristics of K-Pop in various academic fields. This research quantitatively used the participatory use process of K-Pop contents in voluntary participation and dissemination of the audience in the Trans-Media environment. The author examined the use of participatory K-Pop contents from the view point of reparability through big data content analysis. It has been revealed that K-Pop is spreading globally through social media, fans of various countries like to play K-Pop, and they make up their own content and form a participatory culture. In addition, we looked at when the moments of momentum in which participatory use is soaring were popular content and who was the publisher.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.373-381
• /
• 2012

An automatic flow and water quality monitoring system was applied to estimate pollutant loads to an urban stream during storm events in DTV (Daeduk Techno Valley), Daejeon, Korea. The monitoring system consists of rainfall gage, ultrasonic water level meter, water quality sensors for DO, temperature, pH, conductivity, turbidity and automatic water sampler for further laboratory analysis. All data are transmitted through on-line system and the monitoring system is designed to be controlled manually in the field and remotely from laboratory computer. Flow rates were verified with field measurements during storm events and showed good agreements. Automatic sampler was used to collect real time samples and analyzed for BOD, COD, TN, TP, SS and other pollutant concentrations in the laboratory. SWMM (Storm Water Management Model) urban watershed model was applied and calibrated using the observed flow and water quality data for the study area. While flow modeling results showed good agreement for all events, water quality modeling results showed variable levels of agreement. These results indicate that current options in the SWMM model to predict pollutant build up and wash-off effects are not sufficient to satisfy modeling of all the rainfall events under study and thus need further modification. This study showed the automatic monitoring system can be used to provide data to assist further refinement of modeling accuracy. This automatic stormwater monitoring and modeling system can be used to develop basin scale water quality management strategies of urban streams in storm events.

• Restorative Dentistry and Endodontics
• /
• v.12 no.1
• /
• pp.39-49
• /
• 1986

The purpose of this study was to observe characteristic properties through the polarization curves and SEM images from 4 different types of amalgam obtained by using the potentiostats (Princeton EG & G) & SEM (Jeol/35), and to investigate the degree of corrosion on the oxidation peak of the each phase of amalgam. After each amalgam alloy and Hg was triturated as the direction of the manufacturer by means of the mechanical amalgamator (Shofu Co.), the triturated mass was inserted into the cylindrical metal mold which was 12mm in diameter and 10.0mm in height and was condensed by using routine manner. The specimen was removed from the mold and stored at room temperature for about 24 hours. The standard surface preparation was routinely carried out. Anodic polarization measurement was employed to confirm the corrosion behaviour of the amalgams in a 0.9% saline solution (P.H: 6.8-7.0) at $37^{\circ}C$. The initial rest potential (corrosion potential) was determined after 30 minutes of immersion of specimen in electrolyte, and the potential scan was begun at the point of 100mV cathodic from the corrosion potential. The scan rate was 0.17mV/sec. in the study to observe the degree of corrosion of each phase. SEI and EPMA images on the determined oxidation peaks of each amalgam were observed. The results were as follows: 1. In the four anodic polarization curves, low copper amalgams have three oxidation peaks and high copper amalgams have two oxidation peaks, -270mV, +26mV and +179mV(SEC) in the low copper lathe cut, and -300mV, +39mV and +163mV(SEC) in the low copper spherical. -4mV and +154mV(SEC) in the Dispersalloy, and +17mV and +180mV(SEC) in the Tytin as high copper amalgams. 2. ${\gamma}_2$ phase in the low copper amalgam and ${\eta}$ phase in the high copper amalgam were the most corrodible phases and Ag-Cu eutectic in high copper amalgam was the most slowly corroded phase. 3. Low copper amalgam was more susceptible in corrosion than high copper amalgam.

• Korean Journal of Food Science and Technology
• /
• v.7 no.2
• /
• pp.61-68
• /
• 1975

This study was conducted (1) to isolate the film-forming yeast from the commercially available soy sauce, (2) to identify the state of soy sauce fermentation by the use of yeasts, (3) to confirm characteristics of yeasts. The result were as follows. 1. These yeast strains in the soy sauce fermentation test showed full fermentation of whole sugar content, reduction of the pure extract and relative reduction in total nitrogen. Soy sauce color was somehow faded to lower the stability of soy sauce. 2. In anti-fungal activity test butylparaben at a higher level 60 ppm., sodium propionate 2,400 ppm, sodium benzoate 800 ppm., menadion 165 ppm, showed their anti-fungal effect, while alcohol did not show the effect in the 3% additive group. 3. The optimum sodium chloride concentration for these strains in the 2% G.Y.P. medium was 5% and optimum temperature was $30^{\circ}C$. The extinction temperature was $62^{\circ}C$ for strain No-1 and No-3, and was $65^{\circ}C$ for No-2 and No-4. 4. The film-forming soy sauce turned out in the gas chromatogram to possess much flavor of low boiling point as compared with the standard. These flavors were considered due to flavor spoilage of the soy sauce. 5. These isolated yeasts were identified Saccharomyces rouxii (film-forming yeast) in the Lodder's taxanomic study.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.4
• /
• pp.409-417
• /
• 2014

Since the oil price has been significantly jumped for recent some years, the diesel engine of the merchant ship has been mainly used the heavy oil of low quality. Thus, it has been often exposed to severely corrosive environment more and more because temperature of the exhaust gas in a combustion chamber is getting higher and higher with increasing of using the heavy oil of low quality. As a result, wear and corrosion of most parts surrounded with combustion chamber is more serious compared to the other parts of the engine. Therefore, an optimum weldment for these parts is very important to prolong their lifetime in a economical point of view. In this study, four types of filler metals such as Inconel 625, 718, 1.25Cr-0.5Mo and 0.5Mo were welded with SMAW and GTAW methods in the forged steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected zone and base metal were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% H2SO4 solution. The weld metal and base metal exhibited the best and worst corrosion resistance in all cases of filler metals. In particular, the weld metal welded with filler metals of Inconel 718 revealed the best corrosion resistance among the filler metals, and Inconel 625 followed the Inconel 718. Hardness relatively indicated higher value in the weld metal compared to the base metal. Furthermore, Inconel 625 and 718 indicated higher values of hardness compared to 1.25cr-0.5Mo and 0,5Mo filler metals in the weld metal.

• Journal of the Korean Society for Railway
• /
• v.18 no.1
• /
• pp.8-14
• /
• 2015

This paper describes a prediction method for micro-pressure wave emitted from a tunnel on the Kyung-bu high-speed railway. Pressure and micro-pressure wave were measured simultaneously to obtain some constants for the prediction method. The change of a micro-pressure wave were analyzed according to the speed of the train, the track bed type, and the distance from a tunnel portal. At a train speed of 300km/h, the micro-pressure wave of 4.0km long ballast track tunnel is about 7.5Pa; that of 3.3km long slab track tunnel is about 14.3Pa The strength of the micro-pressure wave decreases in inverse proportion to the distance and becomes about 0.5~1.0Pa at a point of 100m from the tunnel exit. Micro-pressure waves were predicted using the formula with the obtained the constants. Using a comparison between the predicted data and field measurement data, it was confirmed that micro-pressure wave can be predicted easily through the prediction formula.

• Korean journal of applied entomology
• /
• v.51 no.4
• /
• pp.305-312
• /
• 2012

This study was conducted to elucidate the seasonal prevalence of adult mosquitoes and occurrence of anopheline larvae in Gimpo, Gyeonggi province, Republic of Korea. Sampling of adult mosquitoes was carried out 18 times from May to September in 2008, using light traps at six sites. A total of 48,919 individuals belonging to 16 species and 8 genera were collected. Aedes vexans nipponii (43%) was the most frequently collected, followed by Anopheles sinensis (34%) and Culex tritaeniorhynchus (14%). The seasonal prevalence of anopheline mosquitoes had a different occurrence compared to that of Cx. tritaeniorhynchus. Anopheline larvae were collected using a standard dipper (size = of 350 ml) at eight habitat types of 203 point locations. Anopheline larvae were confirmed from 138 points (63%). The average larval population per dipper was highest in the lotus plantation (6.9 individuals), followed by irrigation channel (4.5 ind.), dropwort field (3.4 ind.), fallow field (3.1 ind.), paddy field (1.8 ind.), swamp (1.4 ind.), and stream (0.2 ind.). There was no significant relationship observed between larval density and DO, pH, salinity, or distance from blood meal hosts (cowshed, pigsty, chicken-house). In the results of average nearest neighbor analysis (ANNA), the distribution of whole points for mosquito larval collection was clustered, and points with over 4.0 larvae per dipper were randomly distributed. Within the study area Haseong-myeon, those points where over 3.0 larvae were collected were of a dispersed distribution.