• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.11
• /
• pp.1720-1729
• /
• 2001

Wear characteristics of Nylon and acetal pinions against steel gears for different pitch line velocities was studied with a power circulating gear test rig under unlubricated condition. Specific wear rate was measured as a function of tooth number, module, tooth width and total revolution. The worn tooth surfaces were examined with a profile projector. The Nylon pinion showed lower specific wear rate than the acetal pinion. However, the Nylon pinion was fractured at high tooth loads, whereas the acetal pinion exhibited a steady wear behavior. The wear characteristics of Nylon pinion varied significantly with the Pitch line velocity. Wear occurred most severely at the tooth tip and the region immediately below the pitch line of pinion. The dominant wear mechanisms were adhesion and abrasion.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.963-970
• /
• 1994

In speech signal processing, it is very important to detect the pitch exactly. The algorithms for pitch extraction that have been proposed until now are not enough to detect the fine pitch in speech signal. Thus we propose the new algorithm which takes advantage of the G-peak extraction. It is the method to find MZCI(maximum zer-crossing interval) which is defined as cut-off bandwidth rate of LPF (low pass filter)and detect the pitch period of the voiced signals. This algorithm performs robustly with a gross error rate of 3.63% even in 0 dB SNR environment. The gross error rate for clean speech is only 0.18%. Also it is able to process all course with speed.

• Phonetics and Speech Sciences
• /
• v.8 no.4
• /
• pp.131-138
• /
• 2016

This study analyzes the characteristics of good impression using speech manipulation scripts and investigates the characteristics of preferred speech voice. Fourty male and female college students participated in this study. They have been exposed to the Gyeongsang dialect spoken by their friends and family for more than 15 years. Two sample voices(1 male and 1 female), considered as giving good impression, were subject to voice analysis. Two students were asked to read the sample paragraph of 'Walking' and their voice samples were analyzed through Praat. The collected speech data were manipulated into 4 different sets by changing pitch level, degree of loudness and speech rate. First, both men and women received good impression more from pitch-lowered sound than from the original one. Second, men tended to receive good impression more from slightly louder voice than from the natural-pitched one. Third, it was shown that men often felt more drowned to a voice at slightly faster speech rate than at the original speech rate. Overall, both male and female listeners favored lower pitch over the original pitch. Men tended to prefer louder voice sound while women preferred less loud one. Men received better impression at a lower speech rate but women at a faster speech rate.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.5
• /
• pp.77-82
• /
• 1994

In speech signal processing, it is very important to detect the pitch exactly. Although various methods for detecting the pitch of speech signals have been developed, it is difficult to exactly extract the pitch for wide range of speakers and various utterances. Thus we propose a new pitch detection algorithm which takes advantage of the G-peak extraction. It is a method to detect the pitch period of the voiced signals by finding MZCI (maximum zero-crossing interval) of the G-peak which is defined as cut-off bandwidth rate of LPF (low pass filter). This algorithm performs robustly with a gross error rate of 3.63% even in 0 dB SNR environement. The gross error rate for clean speech is only 0.18%. Also it is able to process all courses with high speed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.296-296
• /
• 2012

LCD panel 검사를 위한 Probe unit은 대형 TV 및 모바일용 스마트폰을 중심으로 각광을 받고 있는 소모성 부품으로 최근 pitch의 미세패턴화가 급속히 진행되고 있다. 본 연구에서는 Slit Wafer 제작 공정을 최적화하기 위해 25 um pitch의 마스크를 설계, 제작하였다. 단공과 장공을 staggered 형태로 배열하여 25 um/25 um line/space pitch로 설계하였다. 또한 단위실험을 위해 직접 25 um pitch로 설계하여, 동일한 실험조건을 적용하여 최적 조건을 찾고자 하였다. 반응변수는 Etch rate 및 profile angle로 결정하였으며, 약 200~400 um 에칭된 slit의 상단과 하단의 폭, 그리고 식각깊이를 SEM 측정사진을 통해 정한 후 etch rate 및 profile angle을 결정하였다. 인자는 식각속도 및 wall의 각도를 결정하는 식각 및 passivation 가스의 유량, chamber 압력(etching/passivation), 식각시간 등으로 정하였으며, 이들의 최대값과 최소값 2 수준으로 실험계획을 설계하였다. 식각 조건에 따라 8회의 실험을 수행하였다. 가스의 유량은 SF6 400 sccm, C4F8 400 sccm, 식각 싸이클 시간은 5.2~10.4 sec, passivation 싸이클시간 4 sec로 하였으며, 압력은 식각시 7.5 Pa, passivation 시 10 Pa로 할 경우가 가장 sharp하게 나타났다. Coil power 와 platen power는 각각 2.6 KW, 0.14 KW로 하였으며, 최적화를 위한 인자의 값들은 이 범위에서 조절하였다. 이러한 인자의 조건 조절을 통해 etch rate는 5.6 um/min~6.4 um/min, $88.9{\sim}89.1^{\circ}$의 profile angle을 얻을 수 있었다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.4
• /
• pp.366-371
• /
• 2014

The neural network pitch controller using changing rate of generator speed has been suggested in this paper to regulate wind turbine power above the rated wind speed. The changing rate of generator speed is used in the suggested pitch controller as well as the difference between the rated and current generator speed. Matlab/simulink has been used for simulations and it has been shown that the suggested pitch controller regulates generator speed as the rated speed of 122.9[rad/s].

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.3
• /
• pp.268-276
• /
• 2005

The aim of this paper is to suggest one efficient method for the various requirements of performance during the process designing and producing an impeller. The study considers that the revisions of a pitch angle of an impeller at an axial turbo fan affect an air flow rates and a static pressure rise. The axial turbo fan specified with the 250 Pa maximum static pressure and 1300 CMH fan air flow rates was tested and analyzed by CFD. The Numerical results show that the air flow rates are calculated to 1,175 CMH, 1,223 CMH, 1,270 CMH, 1,340 CMH and 800 CMH in cases that the pitch angles are $44^{\circ},\;49^{\circ},\;54^{\circ},\;59^{\circ},\;and\;64^{\circ}$ respectively. Also the static pressure rises are shown to 108 Pa, 122Pa, 141 Pa, 188 Pa and 63 Pa at the same cases. The air flow rate is increased linearly according to the changes of the pitch angle from $44^{\circ}\;to\;59^{\circ}$ and the maximum air flow rate passing the impeller is increased to $13\%$ over at the case of $59^{\circ}$ pitch angle compared with the reference case of $54^{\circ}$ pitch angle. The static pressure rise is increased linearly according to the changes of the pitch angle from $44^{\circ}\;to\;54^{\circ}$, too. The static pressure rise at the $59^{\circ}$ pitch angle is increased to $33\%$ over compared with the $54^{\circ}$ pitch angle. The result shows that the revisions of pitch angle make the static pressure rise increase widely. However the air flow rates and the static pressure rise at the $64^{\circ}$ pitch angle are suddenly decreased because of over-changed pitch angle.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.6
• /
• pp.1026-1030
• /
• 2011

This paper presented here contains development of variable stability system(VSS) control laws for the KIFS (Korean In-Flight Simulator) aircraft to simulate the dynamics of F-16 aircraft. Development of VSS Control law for pitch rate, roll rate, yaw rate simulation for three specified flight conditions using Model Following Technique with rate feedback autopilot for stability provision. The direct lift force controller was also added to the developed VSS control law to simulate the pitch rate and normal g-load simultaneously. The simulation results show high accuracy of F-16 aircraft's pitch, roll, yaw rate and g-load simulation.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.753-760
• /
• 2007

In this paper, a roll and pitch estimation algorithm using a set of accelerometers and wireless sensor networks(S/N) is presented for use in a passenger vehicle. While an inertial measurement unit(IMU) is generally used for roll/pitch estimation, performance may be degraded in the presence of longitudinal acceleration and yaw motion. To compensate for this performance degradation, a new roll and pitch estimation algorithm is proposed that uses an accelerometer array, global positioning system(GPS) and in-vehicle networks to get information from yaw rate and roll rate sensors. Angular acceleration and roll and pitch approximation are first calculated based on vehicle kinematics. A discrete Kalman filter is then applied to estimate both roll and pitch more precisely by reducing noise from the running engine and from road disturbance. Finally, the feasibility of the proposed algorithm is shown by comparing its performance experimentally with that of an IMU in the framework of an indoor test platform as well as a test vehicle.

• Journal of the Korean Ceramic Society
• /
• v.35 no.9
• /
• pp.974-980
• /
• 1998

This study is concerned with the production of carbon fiber reinforced carbon(C/C) with polyaromatic mesophase pitch as matrix precursor and with the investigation of friction-wear characteristics in ambient air using a constant speed type of friction tester. The main problem in using the polyaromatic mesophase as the matrix precursor is the high viscosity which may limit the complete impregnation of the fiber preform in the vacuum. To solve these problems two dimensional carbon fiber fabrics were infiltrated with meso-phase pitch in the pitch impregnator. After the impregnation and the heat treatment process. C/C com-posites were characterized by density porosity to monitor the influence of high pressure and temperature. It showed that the bulk density was increased and the apparent porosity and the density increasing rate was reduced as repeating the impregnation the carbonization and the heat treatment. The friction-wear charac-teristics of C/C composites were investigated by measuring the average friction coefficient and the specific wear rate as functions friction speed and friction pressure using a constant speed type of friction tester. C/C composite4s showed the average friction coefficient to be reduced as increasing the friction speed and the friction pressure.