• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.327-328
• /
• 2006

본 연구에서는 0-3 타입의 압전 세라믹 - 고분자 복합소재를 제조하기 위해서 $Pb(Zr_{0.54}Ti_{0.48})O_3$ + 0.2 wt% $Cr_2O_3$ + 1 wt% $Nb_2O_5$ 조성을 기본 조성으로 하여, 세라믹-고분자 첨가량에 따른 복합소재의 전기적 특성과 여러 분극조건, 즉 분극온도, 분극시간, 분극전압 변화에 의한 압전 특성을 고찰하였다. 세라믹 첨가비율이 증가함에 따라 유전상수와 압전상수($d_{33}$)는 증가하였으며, 전압상수($g_{33}$)는 급격히 감소하는 경향을 보였으며, 분극시간과 분극전압도 전기적 특성에 영향을 주는 것을 확인하였다. 분극전압 5KV 인가한 고분자 15% 첨가한 복합 소재에서 유전상수 13, 압전상수 $d_{33}$ 23(${\ast}10^{-12}C/N$), 전압상수 $g_{33}$ 170($10^{-3}v.m/N$)의 우수한 특성을 나타내었다.

• 폴리머
• /
• 제28권5호
• /
• pp.361-366
• /
• 2004

가해준 하중에 따라 폴리(비닐리덴 플루오라이드) (PVDF) 필름에서 발생하는 전압을 측정하며 분포형 촉각센서로서의 특성을 연구하였다. PVDF 필름에 전기장과 온도를 달리하면서 극화 (poling)의 변화를 주었고 이에 따른 필름의 압전성을 나타내는 $\beta$-결정상의 피크를 FT-IR. DSC와 XRD를 사용하여 확인하였다. 본 연구에서 사용된 온도와 전압의 영역에서는 극화 온도가 증가함에 따라 그리고 극화 전압이 증가함에 따라 $\beta$-결정상은 증가하였으며, 이에 따라 유전상수가 역시 증가하였다. 8$\times$8어레이 (array)로 제작된 촉각센서에 힘을 가하여 극화에 따른 전압 발생량을 측정한 결과, 극화가 많이 된 시편의 경우 높은 전압이 발생하는 것을 확인하였다.

• 한국음향학회지
• /
• 제22권3호
• /
• pp.202-207
• /
• 2003

초음파트랜스듀서는 초점거리의 제어를 위해서 각 진동요소에 전기회로를 이용한 위상가중치를 부가하는 방식을 사용하고 있다. 그러나 이러한 방법은 진동요소가 증가함에 따라 전기회로가 더욱 복잡해진다. 본 연구에서는 바이몰프형 액츄에이터를 신호의 송수신을 하는PVDF의 뒷부분에 삽입하여 선집속형 트랜스듀서를 제작하였다. 이 트랜스듀서를 사용하여 액츄에이터에 인가되는 전압 변화에 의해 기계적으로 초점거리를 제어할 수 있었다. 이 방법을 사용한 결과 수중에서 선집속형 초음파 트랜스듀서의 초점거리를 곡률 반경의 10%범위까지 제어 가능함을 확인하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제6권4호
• /
• pp.293-298
• /
• 2006

Thermopiezoelectric method, using poly silicon heater and a piezoelectric sensor, was proposed for writing and reading in a probe based data storage system. Resistively heated tip writes data bits while scanning over a polymer media and piezoelectric sensor reads data bits from the self-generated charges induced by the deflection of the cantilever. 34${\times}$34 array of thermopiezoelectric nitride cantilevers were fabricated by a single step wafer level transfer method. We analyzed the noise level of the charge amplifier and measured the noise signal. With the sensor and the charge amplifier 20mn of deflection could be detected at a frequency of 10KHz. Reading signal was obtained from the cantilever array and the sensitivity was calculated.

• Smart Structures and Systems
• /
• 제26권2호
• /
• pp.157-174
• /
• 2020

The guided wave technique is commonly used in structural health monitoring as the guided waves can propagate far in the structures without much energy loss. The guided waves are conventionally generated by the surface-mounted piezoelectric wafer active sensor (PWAS). However, there is still lack of understanding of the wave propagation in layered structures, especially in structures made of anisotropic materials such as carbon fiber reinforced polymer (CFRP) composites. In this paper, the Rayleigh-Lamb wave strain tuning curves in a PWAS-mounted unidirectional CFRP plate are analytically derived using the normal mode expansion (NME) method. The excitation frequency spectrum is then multiplied by the tuning curves to calculate the frequency response spectrum. The corresponding time domain responses are obtained through the inverse Fourier transform. The theoretical calculations are validated through finite element analysis and an experimental study. The PWAS responses under the free, debonded and bonded CFRP conditions are investigated and compared. The results demonstrate that the amplitude and travelling time of wave packet can be used to evaluate the CFRP bonding conditions. The method can work on a baseline-free manner.

• 한국소음진동공학회논문집
• /
• 제14권10호
• /
• pp.1007-1014
• /
• 2004

This paper presents a study of low frequencies volume velocity vibration control of a smart panel in order to reduce sound transmission. A distributed piezoelectric quadratically shaped polyvinylidene fluoride (PVDF) polymer film is used as a uniform force actuator and an array of $4\;{\times}\;4$ accelerometer is used as a volume velocity sensor for the implementation of a single-input single-output control system. The theoretical and experimental study of sensor-.actuator frequency response function shows that this sensor-actuator arrangement provides a required strictly positive real frequency response function below about 900 Hz. Direct velocity feedback could therefore be implemented with a limited gain which gives reductions of about 15 dB in vibration level and about 8 dB in acoustic power level at the (1,1) mode of the smart panel. It has been also shown that the shaping error of PVDF actuator could limit the stability and performance of the control system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.368-373
• /
• 2003

This paper presents a study of low frequencies volume velocity vibration control of a smart panel in order to reduce sound transmission. A distributed piezoelectric quadratically shaped polyvinylidene fluoride (PVDF) polymer film is used as a uniform force actuator and an array of 4$\times$4 accelerometer is used as a volume velocity sensor for the implementation of a single-input single-output con rot system. The theoretical and experimental study of sensor-actuator frequency response function sho vs that this sensor-actuator arrangement provides a required strictly positive real frequency response function below about 900Hz. Direct velocity feedback could therefore be implemented with a limited gain which gives reductions of about 15㏈ in vibration level and about 8 ㏈ in acoustic power level at the (1, 1) mode of the smart Panel. It has been also shown that the shaping error of PVDF actuator could limit he stability and performance of the control system.

• 한국소음진동공학회논문집
• /
• 제17권3호
• /
• pp.264-273
• /
• 2007

A smart panel with structural sensors and actuators for minimizing noise radiation or transmission is described in the paper with the concept of active structural acoustical control. The sensors and actuators are both quadratically shaped piezoelectric polyvinylidene fluoride(PVDF) Polymer films to implement a volume velocity sensor and uniform force actuator respectively. They are collocated on either side of the panel to take advantage of direct velocity feedback(DVFB) strategy, which can guarantee a robust stability and high performance as long as the sensor-actuator response is strictly positive real(SPR). However, the measured sensor-actuator response of the panel showed unexpected result with non-SPR property. In the paper, the reason of the non-SPR property is investigated by theoretical analysis, computer simulation and experimental verification. The investigation reveals that the arrangement of collocated piezoelectric PVDF sensor and actuator pair on a panel is not relevant to get a high feedback gain and good performance with DVFB strategy.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1015-1020
• /
• 2011

최근, MEMS/NEMS 기술을 이용하여 기능성 나노 구조물을 제작하기 위한 공정기술 중에, 마스터 스템프에 형성된 나노패턴을 웨이퍼 등에 복제할 수 있는 나노임프린트 리소그래피 기술이 활발히 연구되고 있다. 본 연구에서는 기존 멀티헤드방식 나노임프린팅 장비에서 사용되던 전동모터를 대신하여 플렉셔 메커니즘과 결합된 나노스템프를 구동하기 위한 사각 형상의 중공형 압전액추에이터를 설계, 제작하였으며, 제조공정이 다른 각각의 시제품의 변위, 발생력 및 응답특성에 관한 검토를 수행한다. 또한, 압전 액추에이터의 변위제어에 대한 제어수법을 간단히 소개하였으며, 제작한 프로토타입의 PI제어기에 의한 변위 제어결과를 소개한다.

• 한국의류학회지
• /
• 제47권3호
• /
• pp.577-592
• /
• 2023

In this study, nanofiber-based textile sensors were developed for motion detection and monitoring. Poly(vinylidene fluoride) (PVDF) nanofibers containing zinc oxide (ZnO) nanoparticles and silver nanowires (AgNW) were fabricated using electrospinning. PVDF was chosen as a piezoelectric polymer, zinc oxide as a piezoelectric ceramic, and AgNW as a metal to improve electric conductivity. The PVDF/ZnO/AgNW nanocomposite fibers were used to develop a textile sensor, which was then incorporated into an elbow band to develop a wearable smart band. Changes in the output voltage and peak-to-peak voltage (V_p-p) generated by the joint's flexion and extension were investigated using a dummy elbow. The β-phase crystallinity of pure PVDF nanofibers was 58% when analyzed using Fourier transform infrared spectroscopy; however, the β-phase crystallinity increased to 70% in PVDF nanofibers containing ZnO and to 78% in PVDF nanocomposite fibers containing both ZnO and AgNW. The textile sensor's output voltage values varied with joint-bending angle; upon increasing the joint angle from 45° to 90° to 150°, the V_p-p value increased from 0.321 V_p-p to 0.542 V_p-p to 0.660 V_p-p respectively. This suggests that the textile sensor can be used to detect and monitor body movements.