• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.304-304
• /
• 2006

One method of Electric Power Generation is to use piezoelectric materials, which form transducers that are able to interchange electrical energy and mechanical force or strain. This study describes the fabrication and properties of piezoelectric transducers for Power Generation application. The structure of the transducers was ceramic-metal-ceramic 3-layered parallel type The center metal layer of phosphorous bronze was bonded by two piezoelectric layers of which have sputtered Ag/Cu(or Ni/Cu) electrode layers on both sides.. The Energy generated by the vibration of piezoelectric transducers Can be achieved by adjusting a suitable piezoelectric constant and mechanical structures. The piezoelectric material used in this application showed the electrical properties of r=4400, $d_{33}\;=\;750\;(10^{-12}\;m/V)$, $d_{31}\;=\;-300\;(10^{-12}\;m/V)$, $k_{33}\;=\;71%$, $Qm\;=\;85$, $T_c\;=\;210^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.6
• /
• pp.484-489
• /
• 2003

In this paper, a single phase driven piezoelectric motor design was presented for linear motion Two metal/ceramic composite actuators, a piezoelectric ring which was bonded to a metal endcap from one side, were used as the active elements of this motor. The motor was composed of a piezoelectric ceramic, a metal ring which has 4 arms, and a guider. Motors with 30 [mm] and 35 [mm] diameter were studied by finite element analysis and experiments. As results, the maximum speed of motor was obtained at resonance frequency. When the applied voltage of the motor increased, the speed was increased. Also, bidirectional motion of the motor was achieved by combining two motors which have different resonance frequency. But the characteristics of bidirectional motion were not equaled, because of the problem of reproduction on the fabrication and the experiment. If present motor is used at the auto-zoom device of a camera, it will have much advantage. Because the direct linear motion can be achieved with a simple structure of motor and no gearbox of total system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.7
• /
• pp.554-558
• /
• 2011

Piezoelectric energy harvester (PEH) as a box type was fabricated in order to harvest mechanical energy imparted to roadways from passing vehicles and convert it into electricity. The PEH was composed of 72 piezoelectric cantilevers with 9 springs with elasticity stick to a bottom of the PEH. For the single piezoelectric cantilever, when a single push with approximately 5 mm displacement was incident to it, power of 0.355 mW was produced at $100\;k{\Omega}$. It is found that the power from the single piezoelectric cantilever increases when spring constant is high. We investigated power of PEH when the moving vehicle passes in it. Power was increased with increasing vehicle speed. When vehicle speed is 30 km/h, power is 20.6 mW.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.516-521
• /
• 2014

This paper describes the development of a new piezoelectric unimorph cantilever structure intended to improve electrical output power, compared to a conventional cantilever. The proposed structure employs a cylindrical bar attached to one side of a steel plate, which is a significant factor in forced vibration mode. The feasibility of the proposed methodology was assessed experimentally and theoretically. The influence of three different types of bar material (i.e., stainless steel, silicon rubber, and urethane), and bar position, on the output voltage were examined and compared with those without the bar. The optimal position and material for the bar were identified through experimental and theoretical analyses. It appears that the electrical output power of the proposed cantilever is about 40% higher than that of a conventional unimorph cantilever.

• Electrical & Electronic Materials
• /
• v.10 no.6
• /
• pp.562-569
• /
• 1997

The resonance characteristics on vibration mode of a transverse type ceramic resonator and the output voltage characteristics of a piezoelectric ceramic transformer are discussed in the effects of partial electrode arrangement (one sided, centered and both sided). A resonance characteristics of resonator depended strongly on both a vibration mode and a electrode structure because of a strain distribution. The maximum resonance current of a piezoelectric ceramic transformer [PCT] with partial centered electrode appeared in λ/2 mode, and that of a PCT with partial both sided electrode appeared in 3λ/2 mode. But the maximum output voltage of those samples appeared in λ/2 mode. In the PCT with partial both sided electrode, the ration of output voltage to input current was highest out of all samples and the poling voltage was a half times of 깬두 type transformer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.10
• /
• pp.766-772
• /
• 2012

Spring supported piezoelectric cantilever structures (SPCS) were fabricated for vibration-based energy harvester application. We selected four elastic springs (A, B, C, and D type) as cantilever's supporter, each elastic spring has a different spring constant (S). The C type of SPCS ($S_C$: 4,649 N/m) showed a extremely low resonance frequency of 81 Hz along with the highest power output of 38.5 mW while the A type of SPCS ($S_A$: 40,629 N/m) didn't show a resonance frequency while. Therefore, it is considered that the lower spring constant lead to a lower resonance frequency of the SPCS. In addition, a tip mass (18 g) at one end of the SPCS could further reduce the resonance frequency without heavy degradation of power output.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.331-332
• /
• 2006

Ag-ceramic composite materials were investigated as internal electrodes for multilayer ceramic actuators (MLCA). Ag-ceramic pastes were prepared by adding PZT-based ceramic powders to a Ag patse in a range of 0 to 50 wt.%. PZT/Ag-PZT multilayered laminates were fabricated by tape casting and fired at low temperatures below $950^{\circ}C$. The addition of ceramic into the Ag electrode resulted in a decrease in the thermal expansion mismatch between the electrode and the ceramic sheet. The maximum strain of PZT/Ag-PZT multilayered actuators were $9{\times}10^{-4}$ under an electric field of 2.5MV/m. In conclusion, Ag-PZT composite materials are efficient for low cost piezoelectric MLCAs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.439-439
• /
• 2009

Nowadays, source of MEMS, USN, Hybrid parts pay attention to energy harvesting. On this paper, energy harvesting was studied using piezoelectric effect. And, piezoelectric generator was designed and fabricated. Generators were designed by FEM simulation program and generators were made by attaching cymbal type metal plates on upper and bottom sides of a disc type piezoelectric ceramic. Output AC power was rectified to DC power by full bridge circuit and converted to regular voltage power by DC-DC converter. The final output power was charged to Ni-Cd battery. Using fabricated generators, output voltages dependant on thickness of ceramic, displacement of vibration, frequency of vibration were measured.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.70-73
• /
• 2000

This paper present a new sort of multilayer piezoelectric ceramic transformer for AC-adapter. This piezoelectric transformer operates in the second longitudinal vibration mode. The output voltage of the multilayer piezoelectric transformer was simulated using ANSYS, that is one of the FEM analysis program. As results, the minimum displacement was occurred at the two paints where one is the middle of input and the other is middle of output side in second thickness extensional vibration mode. And output voltage was inversely decreased by increasing number of output layers. 缀Ѐ㘰〻ሀ䝥湥牡氠瑥捨湯汯杹

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.53-54
• /
• 2009

Nowadays, source of MEMS, USN, Hybrid parts pay attention to energy harvesting. On this paper, energy harvesting was studied using piezoelectric effect. And, piezoelectric generator was designed and fabricated. Generators were designed by FEM simulation program and generators were made by attaching cymbal type metal plates on upper and bottom sides of a disc type piezoelectric ceramic. Using fabricated generators, output voltages dependant on thickness of ceramic, displacement of vibration, frequency of vibration were measured.