• Journal of Adhesion and Interface
• /
• v.21 no.1
• /
• pp.14-19
• /
• 2020

In this study, we synthesized a self-photocuring intermediate(SPI) by Michael addition reaction and synthesized polyurethane acrylate oligomer. Analysis and physical properties of the synthesized SPI and polyurethane acrylate oligomer were confirmed by FT-IR, NMR and UTM. As the content of the SPI increased, the tensile strength increased and the elongation decreased. In addition, since the film was hydrophobic, the surface energy tended to decrease. When the content of the SPI was 40 wt%, adhesion, processability, and pencil hardness were excellent, and solvent resistance was excellent overall.

• Macromolecular Research
• /
• v.13 no.4
• /
• pp.362-365
• /
• 2005

• Macromolecular Research
• /
• v.16 no.1
• /
• pp.31-35
• /
• 2008

Photoreactive polymers as a color filter resist containing both photoreactive acrylate and cinnamate double bonds were synthesized usin two step reactions. The chemical structures of the synthesized polymers were confirmed by $^1H$-NMR and FT-IR spectroscopy. The photoreactive polymers were quite soluble in most common organic solvents and produced excellent quality thin films by spin-coating. The photocuring kinetics of the acrylate and cinnamate double bonds were examined by FT-IR and UV- Vis spectroscopy, which confirmed the excellent photoreactivity of both the acrylate and cinnamate double bonds in the polymers. Upon UV irradiation, photocuring was almost completed within approximately 5 min, irrespective of the type of the prepolymers. The polymers also exhibited superior thermal stability, showing little change in transmittance in the visible region even after heating to $250^{\circ}C$ for one hour. Photolithographic micropatterns could be obtained with a resolution of a few microns.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.532-538
• /
• 2021

In this study, a spray dryer is used to make granules of Y₂O₃ and YF₃, and then Y₅O₄F₇ is synthesized following heat treatment of them under Ar gas atmosphere at 600 ℃. Single and binary monomer mixtures are compared and analyzed to optimize photocurable monomer system for DLP 3D printing. The mixture of HEA and TMPTA at 8:2 ratio exhibits the highest photocuring properties and low viscosity with shear thinning behavior. The optimized photocurable monomer and synthesized Y₅O₄F₇ are therefore mixed and applied to printing process at variable solid contents (60, 70, 80, & 85 wt.%) and light exposure times. Under optimal light exposure conditions (initial exposure time: 1.2 s, basic exposure time: 5 s), YOF composites at 60, 70 & 80 wt.% solid contents are successfully printed. As a result of measuring the size of the printed samples compared to the dimensions of the designed bar type specimen, the deviation is found to increase as the YOF solid content increases. This shows that it is necessary to maximize the photocuring activity of the monomer system and to optimize the exposure time when printing using a high-solids ceramic slurry.

• ETRI Journal
• /
• v.25 no.4
• /
• pp.253-257
• /
• 2003

This study investigated the photochromic properties and characterization of acetyl-substituted diarylethene (DAMBTF6)-doped fluoroacrylates media for holographic storage. For the rewritable holographic recording media, we prepared photochromic polymer films using an acrylate matrix by simple photocuring methods. Switching light sources from a visible (532 nm) to an ultraviolet (365 nm) produced transparent films that changed from pale yellow to red. Holographic recording was performed on the photochromic films by two interfering collimated plane wave beams. Excitation with a visible or ultraviolet light completely erased the records, and the film was rewritable either by 532 nm laser or by 325 nm laser within 2 seconds. Images were recorded onto a pixelated spatial light modulator with rectangular pixel apertures and reconstructed on the photochromic films to show recovery of the original images with high resolution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.165-166
• /
• 2006

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.6
• /
• pp.1561-1567
• /
• 2021

In this study, we have studied synthesis of zirconia-alumina composite coating materials via a low-temperature sol-gel process. The zirconia-alumina composites were prepared by coating zirconia precursor, alumina precursor, and organosilane mixture on a polyethylene terephthalate substrate through three steps: sol-gel process, low-temperature photocuring process, and heat treatment process. The structural properties and element analysis of the composites were confirmed by FT-IR and XPS. The coated composite showed a transmittance of 96% or more in the visible light region with a wavelength of 420 nm or more and pencil hardness of 9H or more. In case of the composite of the molar ratio of zirconia and alumina of 1:4, the highest nanoindentation hardness was measured with 1.212 GPa.

• Journal of Technologic Dentistry
• /
• v.44 no.3
• /
• pp.76-80
• /
• 2022

Purpose: The purpose of this study is to analyze the depth according to curing using photocurable resin for dental three-dimensional printing. Methods: A stainless mold with a height of 4 mm was prepared. Ultraviolet (UV) polymerization resin was injected into the mold. Photocuring was then performed for 5 minutes using a photopolymerizer, and the height was measured using a digital measuring instrument (first group). Second, light polymerization was also performed outside the mold for 5 minutes, and the height was measured using a digital measuring instrument. Third, light polymerization was further performed for 5 minutes, and the height was measured using a digital measuring instrument. Statistical analysis was performed with the Kruskal-Wallis test, which is a nonparametric test (α=0.05). Results: The third group had the largest measurement length, whereas the first group had the smallest. However, the difference between groups was not statistically significant (p>0.05). The color of the first group was different from that of the second and third groups. Conclusion: All of the 4-mm-thick photocured specimens had a curing reaction, but the part that was not directly irradiated with UV did not show its original color.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.2
• /
• pp.203-209
• /
• 2017

The propenyl ether-type monomers which are applicable for cationic photo-polymerization were synthesized by the condensation reaction of mono and di-functional alcohol with allyl bromide. To examine photo-curable reactivity, these monomers were combined with cationic photoinitiator to prepare coating composition. As a result, the initial rate of polymerization of POMB in mono propenyl ether type was 10.2, which was relatively lower than BPOB in di-propenyl ethers type. However, POMB containing 1.5mol% photoinitiator almost quantitatively reacted within 90 seconds. In addition, Sulfonium salt type photo-initiators containing long-alkyl group showed good solubility with monomers and apperaed to have comparatively higher rate of polymerization and conversion ratio when applying DPSA and DPST which have high acidity on all monomers.

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.1-4
• /
• 2013

We proposed a new process to fabricate a high-aspect-ratio microhair having surface wrinkles using the contact-and-tension of a microstamp. Through this work, we observed that regular surface wrinkles were generated on the hair with a diameter of around $20{\mu}m$ due to the uni-directional compressive stress during the photocuring process by ultraviolet light. To do this, we conducted an experimental system setup for contact-and-tension process. From the preliminary test results, we believed that the proposed method can be applied to make a long polymer hair having surface wrinkles for special applications to biomimetics, and some research fields related on surface area such as heat transfer and catalyst enhancement.