• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.4
• /
• pp.304-310
• /
• 2005

The techniques in order to measure the depth of defect in weldment and structure accurately have been developed. Many researches have made efforts to develop the methods for the accurate depth sizing of defect. TOFD is known as the most accurate method of various methods for measuring depth sizing. However, there is a possibility to miss defects because of the limitation of beam coverage for the ultrasound incident angle. In this study, the results for detectability and depth sizing using phased array ultrasonic technique for thick body were compared with those of conventional TOFD technique. It was experimentally confirmed that the phased array ultrasonic TOFD technique gives good detectability and accurate depth measurement for the various types of defects. The phased array ultrasonic TOFD technique developed in this study will contribute to increase the inspection reliability in thick component such as the pressure vessel of power generation industry.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.1
• /
• pp.11-17
• /
• 2020

This study proposes a novel structure for the cross-eye, one of the representative jamming techniques of monopulse sensors. The proposed jammer tranceivers are composed of multi-channels with phased array antenna. We named this structure PRCJ(Phased array Retrodicetive Cross-eye Jammer). In this structure, formulas for calculating cross-eye gain and distance error are derived. We compare the properties of PRCJ with two-element retrodiredtive cross-eye jammer(TRCJ). PRCJ can achieve higher J/S because this structure can steer the spatially combined jamming signal in the direction of the incident monopulse signal. Because of the multiple channels in the phased array, it also increases the degree of freedom of channel matching. Finally, We preform a statistical analysis of the cross-eye gain according to the amplitude and phase errors. From this results, It has been found that PRCJ can get higher cross-eye gain than TRCJ.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.7
• /
• pp.625-634
• /
• 2016

A full digital receiving active phased array antenna generates final receiving beams by digital beam forming of received digital signals in element-level that makes difficult to use typical near-field measurement method. Thus in this paper, a modified near-field measurement method which is suitable for full digital receiving active phased array antenna is proposed. Also the measured results of receiving beam pattern and G/T using developed L-band full digital receiving active phased array antenna are shown for the verification of proposed method.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.5
• /
• pp.299-306
• /
• 2015

A conventional phased array system can control an ultrasonic beam electronically by adjusting the excitation time delay of individual elements in a multi-element probe and produce an ultrasonic image. In Contrast, full matrix capture (FMC) is a data acquisition process that allows receiving ultrasonic signals from one single shot of the phased array transducer element through all the other elements and captures the complete dataset from every possible transmit-receive combination. This FMC data can be used to create the ultrasonic image in post processing. It is possible to produce not only images equivalent to conventional phased array image but also total focusing method (TFM) images with improved resolution and sharpness, which is virtually focused at any point in a region of interest. In this paper, the system that can perform FMC by using a conventional phased array instrument is developed, and a study was conducted on the imaging algorithms to reconstruct sector B-scan and TFM images from FMC dataset.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.317-323
• /
• 2010

The manual ultrasonic examination for the nuclear power plant piping welds has been demonstrated by using KPD(Korean Performance Demonstration) generic procedure. For automated ultrasonic examination, there is no generic procedure and it should be qualified by using applicable automated equipment. Until now, most of qualified procedures used pulse-echo technique and there is no qualified procedure using phased array technique. In this study, data acquisition and analysis software were developed and phased-array transducer and wedge were designed to implement phased array technique for nuclear power plant in-service inspection. The developed procedure are qualified for performance demonstration for the flaw detection, length sizing and depth sizing. The qualified procedure will be applied for the field examination in the nuclear power plant piping weld inspection.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.373-379
• /
• 2010

EMAT has been applied in various fields for flaw detection and material characterization because it has noncontact property in wave generation and a good mode selectivity. Unfortunately, however, EMAT shows low signal to noise ratio relative to commercial contact transducer because of low energy conversion efficiency. If the phase matching through the control of time delay between each coil consisting of the array EMAT is accomplished, it is expected that it will be a solution for the improvement of low signal to noise ratio. In this experiment, the phased array EMATs which consists of 3 or 4 meander coils and one big magnet were fabricated for surface and vertical shear wave generation. Effect of phased delay control on signal directivity and amplitude enhancement was verified. A slit with the depth of 0.5 mm and a side-drill hole of 0.5 mm diameter were clearly detected by fabricated phased array EMATs, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.8
• /
• pp.1963-1970
• /
• 1998

In this paper, a two-dimensional slotline coupling structure is proposed for the planar active phased array antenna system with scanning the beam by coupled oscillators without phase shifters. The operating characteristics are analyzed and experimentally demonstrated. The proposed two-dimensional slotline coupling structure consists of $|{=}|$-type slotline in the ground plane for the coupling of E-plane and H-plane. From the simulation results of coupling strength with the variation of width, length and the number of slotlines, the optimal coupling structure is proposed and applied to $2{\times}5$ elements of planear phased array antenna. The experimental results show that the beamwidth of E-plane and H-pland are $42^{\circ}$ and $15^{\circ}$, respectivly, and the scanning range is from $-20^{\circ}$ to $15^{\circ}$ from the broadside. Therefore, it is shown the two-dimensional slotline coupling structure for oscillator-type active phased array antenna can be applied to the planar phased array antenna system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.371-379
• /
• 2011

Active phased array antenna structure is used for modern multi-function radars. To search targets in high clutter environment, the radar receiver needs high dynamic range performance. Though active phased array antenna structure lead to increase of SNR, the SFDR is not increased. In this paper, high SFDR receiver of X-band active phased array radar was designed and manufactured. One channel digital receiver is connected to 32 T/R modules and one PCB assembly is composed to 2 channel digital receivers with RF part, ADC part, LO distribution part and digital down conversion part. A commercial FIFO board was used for digital receiver measurement about major performance in digital output signal condition. The measured digital receiver gain and SFDR is 33 dB and more than 81 dBc each.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.11
• /
• pp.978-986
• /
• 2016

X-band phased array antenna module for the compensation of deformed beam direction by wing deformation is designed and fabricated. The phased array antenna module consists of array antenna, phase shifter, power divider and control circuit. To select out the best component, the variation of radiation pattern by wing bending and phase error of components is simulated. The fabricated phased array antenna module shows an antenna gain of 5.84 dBi, a return loss of 13.6 dB and a bandwidth of 10.6 % at 9.375 GHz. The test bed was set up to verify the performance of beam direction compensation. This test confirmed that the main beam direction of array antenna has been well restored under wing bending of 9 %.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.62-66
• /
• 2003

Novel coupled line phase shifters and its equivalent phase delay line for compact broadband phased array antennas are proposed. These phase control circuits are designed to be less complex, small size and to use a less number of active devices. The phase shifter is able to control a 120$^{\circ}$ phase shift continuously, and the phase delay line for a reference phase has a fixed 60$^{\circ}$ shifted phase. Both have the low phase error of less than $\pm$3.5$^{\circ}$ and the low gain variations of less than 1 ㏈ within the 300 MHz bandwidth. These proposed circuits are adequate to form the efficient beam-forming networks with compactness, broadband, less complexity, and low cost.