• Journal of Microbiology and Biotechnology
• /
• v.18 no.9
• /
• pp.1522-1528
• /
• 2008

The morphogenetic behavior of a tropical marine Yarrowia lipolytica strain on hydrophobic substrates was studied. Media containing coconut oil or palm kernel oil (rich in lauric and myristic acids) prepared in distilled water or seawater at a neutral pH supported 95% of the cells to undergo a transition from the yeast form to the mycelium form. With potassium laurate, 51 % of the cells were in the mycelium form, whereas with myristate, 32% were in the mycelium form. However, combinations of these two fatty acids in proportions that are present in coconut oil or palm kernel oil enhanced the mycelium formation to 65%. The culture also produced extracellular lipases during the morphogenetic change. The yeast cells were found to attach to the large droplets of the hydrophobic substrates during the transition, while the mycelia were associated with the aqueous phase. The alkane-grown yeast partitioned more efficiently in the hydrophobic phases when compared with the coconut oil-grown mycelia. A fatty acid analysis of the mycelial form revealed the presence of lauric acid in addition to the long-chain saturated and unsaturated fatty acids observed in the yeast form. The mycelia underwent a rapid transition to the yeast form with n-dodecane, a medium-chain aliphatic hydrocarbon. Thus, the fungus displayed a differential behavior towards the two types of saturated hydrophobic substrates.

• Journal of the Korean Ceramic Society
• /
• v.49 no.3
• /
• pp.253-259
• /
• 2012

In this study, crystal structural changes and dielectric properties of $(1-x)Pb(Yb_{1/2}Nb_{1/2})O_3-xPbTiO_3$ ((1-x)PYN-xPT) solid solutions were measured and analyzed with respect to the $PbTiO_3$ (PT) contents ($0.40{\leq}x{\leq}0.60$). From X-ray diffraction (XRD) measurements, (1-x)PYN-xPT solid solutions showed changes of the crystal structure from pseudocubic ($0.40{\leq}x{\leq}0.44$) to tetragonal ($0.52{\leq}x{\leq}0.60$) on increasing PT contents and exhibited the coexistence of pseudocubic and tetragonal phase near the morphotropic phase boundary (MPB) composition ($0.46{\leq}x{\leq}0.50$). The dielectric constant showed a maximum value at x = 0.46 and the maximum values in (1-x)PYN-xPT decreased with higher PT contents. The phase transition temperatures of (1-x)PYN-xPT solid solutions increased over the whole composition ranges tested ($0.40{\leq}x{\leq}0.60$).

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1248-1254
• /
• 2018

Magnetization versus temperature and magnetic-field measurements, M(T, $H_a$), have been carried out to study the magnetic and critical properties of polycrystalline $La_{1-x}Ba_xCoO_3$ (x = 0.3 and 0.5) cobaltites. These compounds with the density of ${\sim}6.2g/cm^3$ crystallized in the $R{\bar{3}}c$ rhombohedral and $Pm{\bar{3}}m$ cubic structures, respectively. With an applied field $H_a=200Oe$, M(T) data have revealed that the samples with x = 0.3 and 0.5 exhibit the ferromagnetic-paramagnetic (FM-PM) phase transition at the Curie temperature points $T_C=202$ and 157 K, respectively. At 4.2 K, the saturation magnetization ($M_{sat}$) decreases from 35.9 emu/g for x = 0.3-26.1 emu/g for x = 0.5. Particularly, the critical-behavior analyses in the vicinity of $T_C$ reveal all samples undergoing a second-order phase transition, with critical exponent values (${\beta}=0.328$ and ${\gamma}=1.251$ for x = 0.3, and ${\beta}=0.331$ and ${\gamma}=1.246$ for x = 0.5) close to those expected for the 3D Ising model. This proves short-range magnetic order existing in $La_{1-x}Ba_xCoO_3$. We believe that magnetic inhomogeneities due to the mixture of hole-rich FM regions (confined in the trivalent-cobalt hole-poor anti-FM matrix) and uniaxial anisotropy prevent long-range order in $La_{1-x}Ba_xCoO_3$.

• Macromolecular Research
• /
• v.17 no.6
• /
• pp.365-377
• /
• 2009

In this feature article, we briefly review the new methods we have utilized recently in the investigation of morphology and phase behavior of block copolymers. We first describe the chromatographic fractionation method to purify block copolymers from their side products of mainly homopolymers or block copolymer precursors inadvertently terminated upon addition of the next monomer in the sequential anionic polymerization. The chromatographic method is extended to the fractionation of the individual block of diblock copolymers which can yield the diblock copolymer fractions of different composition and molecular weight, which also have narrower distributions in both molecular weight and composition. A more detailed phase diagram could be constructed from the set of block copolymer fractions without the need of acquiring many block copolymers each prepared by anionic polymerization. The fractions with narrow distribution in both molecular weight and composition exhibit better long-range ordering and sharper phase transition. Next, epitaxial relationships between two ordered structures in block copolymer thin film is discussed. We employed the direct visualization method, transmission electron microtomography(TEMT) to scrutinize the grain boundary structure.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.549-557
• /
• 2008

Despite of the laminar-turbulent transition region co-exist with fully turbulence region around the leading edge of an airfoil, still lots of researchers apply to fully turbulence models to predict aerodynamic characteristics. It is well known that fully turbulent model such as standard k-model couldn't predict the complex stall and the separation behavior on an airfoil accurately, it usually leads to over prediction of the aerodynamic characteristics such as lift and drag forces. So, we apply correlation based transition model to predict aerodynamic performance of the NREL (National Renewable Energy Laboratory) Phase IV wind turbine. And also, compare the computed results from transition model with experimental measurement and fully turbulence results. Results are presented for a range of wind speed, for a NREL Phase IV wind turbine rotor. Low speed shaft torque, power, root bending moment, aerodynamic coefficients of 2D airfoil and several flow field figures results included in this study. As a result, the low speed shaft torque predicted by transitional turbulence model is very good agree with the experimental measurement in whole operating conditions but fully turbulent model(${\kappa}-\;{\varepsilon}$) over predict the shaft torque after 7m/s. Root bending moment is also good agreement between the prediction and experiments for most of the operating conditions, especially with the transition model.

• Polymer(Korea)
• /
• v.28 no.4
• /
• pp.344-351
• /
• 2004

Poly(ethylene glycol)-based diblock and triblock polyester copolymers stimulating to temperature were studied as injectable biomaterials in drug delivery system because of their nontoxicity, biocompatibility and biodegradability. We synthesized the diblock copolymers consisting of methoxy poly(ethylene glycol) (MPEG) (M$_{n}$=750 g/mole) and poly($\varepsilon$-caprolactone) (PCL) by ring opening polymerization of $\varepsilon$-CL with MPEG as an initiator in the presence of HCl . Et$_2$O. The aqueous solution of synthesized diblock copolymers represented sol phase at room temperature and a sol to gel phase transition as the temperature increased from room temperature to body temperature. To confirm the in vivo gel formation, we observed the formation of gel in the mice body after injection of 20 wt% aqueous solution of each block copolymer. After 2 months, we observed the maintenance of gel without dispersion in mice. In this study, we synthesized diblock copolymers exhibiting sol-gel phase transition and confirmed the feasibility as biomaterials of injectable implantation.n.

• Tribology and Lubricants
• /
• v.11 no.4
• /
• pp.21-27
• /
• 1995

The effects of interface boundary strength on wear and wear transition during sliding have been investigated in silicon carbide ceramics. Three different microstructures, i.e., solid state sintered silicon carbide, liquid phase sintered silicon carbide and liquid phase sintered silicon carbide composite reinforced with TiB$_{2}$ particulates, were designed by hot pressing. Examinations of crack patterns and fracture modes indicated that interface boundaries were relatively strong between silicon carbide grains in the solid state sintered silicon carbide, intermediate in the liquid phase sintered silicon carbide and weak between silicon carbide grains and TiB$_{2}$ particles in the composite. Wear data and examinations of worn surfaces revealed that the wear behavior of these silicon carbide ceramics could be significantly affected by the interface strength. In the solid state sintered silicon carbide, the wear occurred by a grooving process. In the liquid phase sintered silicon carbide and composite, on the other hand, an abrupt transition in wear mechanism from initial grooving to grain pull-out process occurred during the test. The transition occurred significantly earlier in the composite than in the carbide.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.10a
• /
• pp.140-140
• /
• 1997

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2005.04a
• /
• pp.33-34
• /
• 2005

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.478-485
• /
• 2018

The effect of reduced graphene oxide (RGO) addition on the dielectric and piezoelectric behavior of the polyvinylidene fluoride (PVDF) films was studied. Dielectric constant increased by four times and piezoelectric coefficient also increased twice by the addition of RGO in the PVDF films. Based on capacitance-voltage and ellipsometry measurements and the Kramers-Kronig transformation, it is concluded that the enhanced dielectric and piezoelectric properties of the PVDF/RGO films resulted from the increased orientational polarization due to a phase transition from nonpolar crystalline ${\alpha}$ phase to polar crystalline ${\beta}$ phase in the PVDF structure.