• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.415-422
• /
• 2014

This paper presents a new approach to solve the multi area unit commitment problem (MAUCP) using an evolutionary programming based particle swarm optimization (EPPSO) method. The objective of this paper is to determine the optimal or near optimal commitment schedule for generating units located in multiple areas that are interconnected via tie lines. The evolutionary programming based particle swarm optimization method is used to solve multi area unit commitment problem, allocated generation for each area and find the operating cost of generation for each hour. Joint operation of generation resources can result in significant operational cost savings. Power transfer between the areas through the tie lines depends upon the operating cost of generation at each hour and tie line transfer limits. Case study of four areas with different load pattern each containing 7 units (NTPS) and 26 units connected via tie lines have been taken for analysis. Numerical results showed comparing the operating cost using evolutionary programming-based particle swarm optimization method with conventional dynamic programming (DP), evolutionary programming (EP), and particle swarm optimization (PSO) method. Experimental results show that the application of this evolutionary programming based particle swarm optimization method has the potential to solve multi area unit commitment problem with lesser computation time.

• Journal of Aerospace System Engineering
• /
• v.13 no.1
• /
• pp.69-76
• /
• 2019

In this study, resin flow analysis of resin transfer moulding (RTM) method was performed for mould design of composite structure. The target composite structure was a tank used for fluid storage. Natural c fiber composite was adopted for composite structural design of the fluid storage tank. RTM was adopted for manufacturing of the tank using natural fiber composites. Resin flow analysis was performed to find the proper RTM conditions of the tank. The resin flow analysis was performed using the commercial FEM flow simulation software. After repeated analysis while changing the location of resin inlet and outlet, the proper resin filling time and pattern were found.

• Design & Manufacturing
• /
• v.15 no.4
• /
• pp.57-64
• /
• 2021

In recent materials industry, researches on the technology to manufacture super hydrophobic surface by effectively controlling the wettability of solid surface are expanding. Research on the fabrication of super hydrophobic surface has been studied not only for basic research but also for self-cleaning, anti-icing, anti-friction, flow resistance reduction in construction, textile, communication, military and aviation fields. A super hydrophobic surface is defined as a surface having a water droplet contact angle of 150 ° or more. The contact angle is determined by the surface energy and is influenced not only by the chemical properties of the surface but also by the rough structure. In this paper, maskless lithography using DMD, electro etching, anodizing and hot embossing are used to make the polymer resin PMMA surface super hydrophobic. In the fabrication of microstructure, DMDs are limited by the spacing of microstructure due to the structural limitations of the mirrors. In order to overcome this, maskless lithography using a transfer mechanism was used in this paper. In this paper, a super hydrophobic surface with micro and nano composite structure was fabricated. And the wettability characteristics of the micro pattern surface were analyzed.

• Archives of Plastic Surgery
• /
• v.50 no.2
• /
• pp.188-193
• /
• 2023

Vascular injury following traumatic knee injury quoted in the literature ranges from 3.3 to 65%, depending on the magnitude and pattern of the injury. Timely recognition is crucial to ensure the revascularization is done within 6 to 8 hours from the time of injury to avoid significant morbidity, amputation, and medicolegal ramifications. We present a case of an ischemic limb following delayed diagnosis of popliteal artery injury after knee dislocation. Even though we have successfully repaired the popliteal artery, the evolving ischemia over the distal limb poses a reconstruction challenge. Multiple surgical debridement procedures were performed to control the local tissue infection. Free tissue transfer with chimeric latissimus dorsi flap was done to resurface the defect. However, the forefoot became gangrenous despite a free muscle flap transfer. His limb appeared destined for amputation in the vicinity of tissue and recipient vessels, but we chose to use a cross-leg free flap as an option for limb salvage.

• Korean Chemical Engineering Research
• /
• v.62 no.2
• /
• pp.191-199
• /
• 2024

A study was conducted on a tubular heat exchanger to improve its heat transfer rate by using a novel baffle plate design with discontinuous swirling patterns. The design consisted of perforated baffle plates with rectangular air deflectors positioned at varying angles. The tubes in the heat exchanger were arranged in a consistent alignment with the airflow direction and exposed to a uniform heat flux on their surfaces. Each baffle plate included sixteen deflectors inclined at the same angle and arranged in a clockwise pattern. This arrangement induced a swirling motion of the air inside a circular duct where the heated tubes were located, leading to increased turbulence and improved heat transfer on the tube surfaces. The spacing between the baffle plates was adjusted at different pitch ratios, and the Reynolds number was controlled within a range of 16,000 to 29,000. The effects of pitch ratios and inclination angles on the heat exchanger's performance were analyzed. The results indicated that using a baffle plate with rectangular deflectors inclined at 30° and a pitch ratio of 1.2 resulted in an average increase of 1.29 in the thermal enhancement factor.

• Wind and Structures
• /
• v.39 no.1
• /
• pp.31-45
• /
• 2024

This paper examines the flow characteristics around an inclined prism with a U-shaped cross-section ("U-profile") and investigates the connection between the flow and flow-induced vibrations. The study employs a combined approach that involves wind tunnel experiments and computational fluid dynamics (CFD) using an unsteady Reynolds-averaged Navier-Stokes (RANS) turbulence model. Distinct vortex formation patterns are observed in the flow field surrounding the stationary inclined profile. When the cavity of the profile faces away from the incoming flow, large vortices develop behind the profile. Conversely, when the cavity is oriented towards the oncoming flow, these vortices form within the cavity. Notably, due to the slow movement of these large vortices through the cavity, the frequency at which vortices are shed in the negative inclination case is lower compared to the positive inclination, where they form in the wake. Wind tunnel experiments reveal an intermittent transition between the two vortex formation patterns at zero inclination. Large vortices sporadically emerge both in the cavity and behind the profile. The simulation results demonstrate that when these large vortices occur at a frequency close to the structure's natural frequency, they induce prominent pitch vibrations. This phenomenon is also sought after and presented in coupled vibration experiments. Additionally, the simulations indicate that when the natural frequency of the structure is considerably lower than the vortex shedding frequency, this type of vibration can be observed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.1
• /
• pp.13-24
• /
• 1988

This paper is concentrated on the development of oxygen transfer system by U-tube deep shaft in biological fluidised bed process. The depth of the shaft is 32 m, it is composed of downcomer and riser. Not only flow pattern and oxygen transfer in the deep shaft but also oxygen limitation in biofilm and oxygen utilization in biological fluidised bed are investigated. In this investigation, driving force for liquid circulation in the deep shaft is affected by air injection depth and gas hold-up in downcomer. Flow pattern of the deep shaft is revealed to plug flow. When flow velocity in the deep shaft is maintained to 0.52 m/sec, $K_La$ value is peak at 25~30 m depth in riser. The efficiency of dissolved oxygen supply which passed from the deep shaft to biological fluidised bed is estimated to 56~81 % in the organic wastewater treatment using the deep shaft and when dissolved oxygen concentration is 9.2 mg/l and over, limiting factors of flux and substrate within biofilm are organic materials. Terefore, organic loadings could be increase without decreasing of BOD removal efficiency.

• Journal of Embryo Transfer
• /
• v.25 no.2
• /
• pp.127-131
• /
• 2010

The objective of this study was to determine the mRNA expression patterns of several putative imprinted genes in in vivo and in vitro fertilized, parthenogenetic, and cloned porcine preimplantation embryos. Both maternally (Dlk1, IGF2, Peg1/Mest and Ndn) and paternally (IGF2r, H19 and Xist) imprinted genes were selected. We have used reverse transcription polymerase chain reaction (RT-PCR) to investigate gene expression patterns in the porcine embryos. IGF2 transcripts were detected in the most of embryos. In nuclear transfer (NT), Peg1/MEST transcripts showed fluctuating pattern. Dlk1 was only expressed partially from the morula and blastocyst stage of NT embryos. Ndn gene expression was started somewhat early for in vivo embryos. However, the expressions of maternally imprinted genes were similar in all types of blastocysts (NT, in vivo and in vitro fertilized, and parthenogenetic embryos). The IGF2R gene expression level was somewhat irregular and varied among samples. However, for the majority samples of all types of embryos, IGF2R expression was diminished after one- to two-cell stages and reappeared at the morulae or blastocyst stage embryos. H19 gene was only expressed early in parthenogenetic and in vivo embryos. For NT embryos, H19 was only expressed in blastocysts. Xist expression was detected in all blastocysts with the earliest being in vivo 8-cell stage embryos and the last one being NT blastocysts. These putative imprinted genes appeared to have stage specific expression patterns with a fluctuating pattern for some genes (Peg/Mest, IGF2r, H19). These results suggest that stage specific presence of imprinted genes can affect the embryo implantation and fetal development.

• Journal of Music and Human Behavior
• /
• v.3 no.1
• /
• pp.63-76
• /
• 2006

Melody is defined as adding spatial dimension to the rhythm which is temporal concept. Being able to understand melodic pattern and to reproduce the pattern also requires cognitive skills. Since 1980, there has been much research on the relationship between academic skills and music cognitive skills, and how to transfer the skills learned in music work to the academic learning. The study purported to examine various research outcomes dealing with the correlational and causal relationships between musical and academic skills. The two dominating theories explaining the connection between two skills ares are "neural theory" and "near transfer theory." The theories focus mainly on the transference of spatial and temporal reasoning which are reinforced in the musical learning. The study reviewed the existing meta-analysis studies, which provided evidence for positive correlation between academic and musical skills, and significance of musical learning in academic skills. The study further examined specific skills area that musical learning is correlated, such as mathematics and reading. The research stated that among many mathematical concepts, proportional topics have the strongest correlation with musical skills. Also with reading, temporal processing also has strong relationship with auditory skills and motor skills, and further affect language and literacy ability. The study suggest that skills learned in the musical work can be transferred to other areas of learning and structured music activities may be every efficient for children for facilitating academic concepts.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.161-168
• /
• 2006

본 연구는 공간적 정보의 청각적 제시 가능성을 확인하기 위해 머리전달함수(head-related transfer function: HRTF)를 통해 생성된 3D 사운드를 가상공간상 대상 위치의 직각형태(orthogonal pattern), 혹은 대각형태(diagonal pattern)의 조합으로 배열하여 투시장치(See-Through HMD)로 증강현실을 경험하고 있는 사용자 과제수행의 정확성을 측정하였다. 본 연구에서 실시한 실험들의 결과를 종합하면, 3D 사운드로 대상의 위치 정보를 제시할 때는 사용자로부터의 방향은 직각으로 위치시키는 정보 배열이 정확성을 확보할 수 있고, 또한 가상적 깊이를 이용하여 정보를 배열하는 것도 그 깊이를 구분할 수 있으나 정확성이 떨어짐을 확인하였다. 특히 보다 현실적인 과제 상황에서의 수행을 비교하기 위해 일차과제(primary task)를 하는 동안 제시된 청각자극 조건에서 이런 정확성의 차이가 마찬가지로 나타났다. 이런 결과를 통해 3D 사운드로 대상의 위치와 같은 공간적 정보를 제시 가능한 최적의 배열 형태를 제안하는데, 이는 어떤 패턴으로 정보를 구조화하여 제시하느냐에 따라 청각적 위치 정보 제시의 성공 여부가 결정된다는 것을 의미한다.