• 한국의류학회지
• /
• 제30권1호
• /
• pp.157-166
• /
• 2006

The human body, which is composed of concave and convex curvatures, makes it difficult to transfer into 2D patterns directly from 3D data. In previous studies. Jeong, et al.(2004) suggested the block method was fester and easier when dealing with the triangular patches of male's upper dress form. Although the block method is useful to make a pattern, the information(area, length, etc.) from a 2D pattern would be different depending on the direction of the block method. As a result horizontal and diagonal block methods were suggested as optimal methods for 2D tight-fitting patterns. These block methods were closer to the original area of the 3D scan data than the vertical block method. The total area of the 2D pattern obtained by the horizontal and diagonal block methods showed little differences. In case of the horizontal and diagonal block methods, the total error of the 2D pattern area ranged from $0.01\%\~0.25\%$. In comparing the length of the 2D pattern with that of the 3D scan data, the obtained 2D pattern was $0.1\~0.2cm$ shorter than the 3D scan data, which was within the acceptable range of errors in making clothes. 3D space distribution images between the body surface and the experimental clothing were also measured and $3\%$ enlargement of the original pattern was verified as the adequate adjustment.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1308-1317
• /
• 2009

우리나라 대중교통 시스템은 서로 다른 수단간 복합적인 상호 연계로 그 교차지점에서 승객의 이동 이 많이 발생하는 환승 위치가 점점 많아지고 있다. 즉, 2 개 이상의 교통수단이 한 곳에서 교차하는 환승센터의 올바른 기능은 보행자의 편리성과 안락함과 직결되고, 그로 인한 더 많은 대중교통 이용유발이 촉진된다. 이처럼 중요한 기능을 담당하는 역할에도 불구하고 국내에는 아직 환승보행센터의 배치기준이나 그것을 평가할 수 있는 기준을 제시하지 못하고 있다. 따라서 본 연구에서는 환승센터에서 보행자의 이용실태(환승거리 및 시간, 접근거리 및 시간, 역사내 승객 이동경로)를 조사 분석하였다. 그 분석결과를 토대로 환승센터에서의 연계시설 배치 평가기준을 승용차 이용자 보행 편리성과 대중교통 이용자 보행 편리성으로 나누어 평가하는 방안을 제시하였다. 환승시설에서의 배치 평가기준은 보행자의 주요 이동 경로률 설정하고, 그에 따른 도보시간을 평가기준으로 설정하였다.

• 설비공학논문집
• /
• 제19권9호
• /
• pp.615-621
• /
• 2007

Experimental study on the heat transfer characteristics of $CO_2$ in a horizontal smooth tube was carried out to investigate the heat transfer coefficient and pressure drop during evaporation of $CO_2$. The experiment apparatus consisted of a test section, a DC power supply, a heater, a chiller, a mass flow meter, a pump and a measurement system. Experiment was conducted for various mass fluxes ($200{\sim}1200kg/m^2s$), heat flukes ($10{\sim}100kW/m^2$) and saturation temperatures (-5, 0, $5^{\circ}C$). With increasing the heat flux, the evaporation heat transfer coefficient increased. But the variation of the heat transfer coefficient on the increase of the mass flux was not large. And the significantly drops of the heat transfer coefficient was observed at any heat flux and mass flux because of the change of the flow pattern in the tube. With increasing the saturation temperature, the heat transfer coefficient increased due to the promotion of a nucleate boiling. The measured pressure drop during evaporation increased with increasing the mass flux and decreasing the saturation temperature.

• Journal of Electrical Engineering and Technology
• /
• 제12권1호
• /
• pp.396-401
• /
• 2017

In this paper, a device to analyze gait pattern was developed by using a 2-axis acceleration sensor attached to the foot. The 1st low-pass filter was adapted to limit the frequency band up to 5 Hz. An algorithm to detect the peak value exceeding the threshold voltage of an X-axis acceleration sensor and a Z-axis acceleration sensor was developed and normal and abnormal walking patterns were thus differentiated. Also, MCU and Bluetooth were combined to transfer the data to other MCUs to display on an LCD; the size of the device could then be reduced. The new algorithm and the device allowed the individual walking patterns to be easily measured at a low cost and with less restriction on activities compared to conventional multiple pressure sensors or motion camera system.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2005년도 추계 학술대회
• /
• pp.147-150
• /
• 2005

We process a novel approach cal led combined nanoimprint and photolithography (CNP) to greatly simplify the fabrication in conventional nanoimprint lithography (NIL). In this study, a novel HMM with anti-sticking $SiO_2$ layer is introduced to improve the quality of transferred pattern. The surface property was investigated using contact angle measurement and spectrophotometer. Replicate pattern with CNP using HMM showed complete pattern transfer without defect.

• 한국산학기술학회논문지
• /
• 제18권5호
• /
• pp.475-480
• /
• 2017

본 논문에서는 레이저 유도증착 공정을 사용하여 절연기판위에 미세패턴의 전도성 향상시켰다. 기존의 레이저 유도증착의 공정에서 발생하는 높은 레이저빔 에너지로 인하여, 미세패턴의 낮은 증착밀도, 산화와 같은 문제점이 있다. 이러한 문제점을 폴리머 코팅층을 사용하여 증착정밀도와 전도성 향상하였다. 실리콘 웨이퍼 위에 미세패턴 증착을 위해서 크롬, 구리를 사용하였다. 본 연구에서는 다중펄스 방식의 레이저 빔을 금속박막에 조사하여 절연기판(insulating substrate: $SiO_2$) 위에 시드 층을 형성하고, 형성된 시드 층위에 무전해 도금을 적용하여 미세패턴 및 구조물을 제작하는 복합공정기술을 개발하였다. 레이저빔의 다중 스캔방식으로 조사함으로서 레이저빔의 에너지가 증착 층의 증착밀도와 표면품위를 향상시키고, 미세전극 패턴으로 사용가능한 전기 전도성을 갖게 되었음 알 수 있었다. 레이저 직접묘화법과 무전해 도금을 적용한 복합공정을 이용하여 미세전극을 증착 한 후 비저항을 측정한 결과 도금 전 저항이 $6.4{\Omega}$, 도금 후의 저항이 $2.6{\Omega}$으로 미세전극 패턴의 표면조직이 균일하고 증착되었다. 표면조직이 균일하고 치밀하게 증착되었기 때문에 전기 전도도가 약 3배정도 향상되었다.

• 대한기계학회논문집B
• /
• 제24권8호
• /
• pp.1085-1096
• /
• 2000

An experimental study was performed to examine the heat and mass transfer characteristics of $LiBr-H_2O$ solution flowing over a single horizontal tube with the water vapor absorption. Effects of the flow rate and the temperature of the solution at the top of the tube, the absorber pressure and the drainage pattern were considered. The absorption rate depends highly on the absorber pressure at the low flow rate condition while on the solution inlet temperature at the high flow rate condition. Also, when the flow rate is low, the absorption performance with the sheet flow drainage appeared to be higher than that with the dripping/jet drainage. However, at the high flow rate condition, the case became reversed. The liquid film became wavy with the higher absorption rate. The waves were more probable to form with the lower flow rate and temperature of the solution, and with the higher absorber pressure.

• 한국전자파학회논문지
• /
• 제14권4호
• /
• pp.363-368
• /
• 2003

본 논문에서는 고전력을 전송하기 위한 시스템에 사용되는 혼 안테나에 요구되는 특성을 연구하고 그에 따라 여러 혼 안테나의 특성을 비교, 분석하였으며, 최종적으로 다중 모드를 사용하는 원형 혼 안테나를 제안하였다. 고전력 전송 시스템에서는 전력 전송 효율이 매우 중요하며, 이를 위해 반사판 급전 혼 안테나로서 원형의 대칭 적인 방사패턴이 필요하며, 전력 누수와 간섭을 줄이기 위해 부엽이 억제되어야 한다. 뿐만 아니라 다중 모드를 사용함으로써, 혼 안테나의 전체적인 길이를 줄일 수 있고, 반사판 안테나의 형태, 방향에 따라 혼 안테나의 방사 패턴을 자유로이 조절할 수 있다. 또한 제작을 통해 이를 확인하였다.

• 한국태양에너지학회 논문집
• /
• 제35권1호
• /
• pp.69-80
• /
• 2015

A series of numerical analyses was conducted to predict the thermal performance of a solar air heater depending on the hole configuration and geometry in the absorber plate. The planar dimensions of the prototype were 1 m (W) by 1.6 m (H), and the maximum air flow considered was $187m^3/h$. It was considered that protruding holes with a triangular opening in the absorber plate would invoke turbulence in the air flow to enhance the convection heat transfer. Six different hole configurations were investigated and compared with each other, while the hole opening height was considered as a design variable. Three-dimensional transient analyses were performed with a commercial software package on the airflow and heat transfer in the model. The numerical results were analyzed and compared from the view point of the outlet air temperature and its time response to derive the optimal hole pattern and hole opening height.

• 한국표면공학회지
• /
• 제51권6호
• /
• pp.387-392
• /
• 2018

Nanopatterning is one of the essential nanotechnologies to fabricate electronic and energy nanodevices. Therefore, many research group members made a lot of efforts to develop simple and useful nanopatterning methods to obtain highly ordered nanostructures with functionality. In this study, in order to achieve pattern formation of three-dimensional (3D) hierarchical nanostructures, we introduce a simple and useful patterning method (nano-transfer printing (n-TP) process) consisting of various linewidths for diverse materials. Pt and $WO_3$ hybrid line structures were successfully stacked on a flexible polyimide substrate as a multi-layered hybrid 3D pattern of Pt/WO3/Pt with line-widths of $1{\mu}m$, $1{\mu}m$ and 250 nm, respectively. This simple approach suggests how to fabricate multiscale hybrid nanostructures composed of multiple materials. In addition, functional hybrid nanostructures can be expected to be applicable to various next-generation electronic devices, such as nonvolatile memories and energy harvesters.