• Journal of Korea Water Resources Association
• /
• v.53 no.1
• /
• pp.45-56
• /
• 2020

This study aims to quantify the uncertainty that can be induced by the objective function when calibrating SWAT parameters using SWAT-CUP. SWAT model was constructed to estimate runoff in Naesenong-cheon, which is the one of mid-watershed in Nakdong River basin, and then automatic calibration was performed using eight objective functions (R², bR², NS, MNS, KGE, PBIAS, RSR, and SSQR). The optimum parameter sets obtained from each objective function showed different ranges, and thus the corresponding hydrologic characteristics of simulated data were also derived differently. This is because each objective function is sensitive to specific hydrologic signatures and evaluates model performance in an unique way. In other words, one objective function might be sensitive to the residual of the extreme value, so that well produce the peak value, whereas ignores the average or low flow residuals. Therefore, the hydrological similarity between the simulated and measured values was evaluated in order to select the optimum objective function. The hydrologic signatures, which include not only the magnitude, but also the ratio of the inclining and declining time in hydrograph, were defined to consider the timing of the flow occurrence, the response of watershed, and the increasing and decreasing trend. The results of evaluation were quantified by scoring method, and hence the optimal objective functions for SWAT parameter calibration were determined as MNS (342.48) and SSQR (346.45) with the highest total scores.

• Journal of Korea Water Resources Association
• /
• v.46 no.1
• /
• pp.73-85
• /
• 2013

The researches on the parameter estimation for storage function method have been conducted for a long time using different methods. However, the determination of the optimal parameters takes a long time and there is a controversy that the proposed optimal parameters do not likely represent the physical characteristics of watershed. In this study, the characteristics of the continuity and storage function equation was analyzed and sensitivities were evaluated. As the result, the only optimal solution is suggested among several local optimums. It is also shown that the lag time is able to be determined using the direct runoff starting time of the watershed. From the sensitivity analysis, it is also proved that the determination of the lag time is very important and the only optimal solution could be found easily after selecting the lag time. Therefore, unlike the traditional optimization method, the proposed method does not take a long time to find the optimal solution which is depending on the characteristics of the rainfall events. The fixed coefficient method which is a method to estimate the optimal parameters of storage function method has been modified using the proposed method. Therefore, the practical efficiency to apply storage function method could be enhanced by applying the proposed method. While the traditional method takes care only the error of the runoff hydrograph, it is very important that the proposed method considers the characteristics of the watershed.

• Journal of Korean Society of Transportation
• /
• v.26 no.3
• /
• pp.17-29
• /
• 2008

A volume-delay function(VDF) has been used to describe the relation between traffic volumes and delay experienced by travelers on the roads traveling from origin to destination, which has been usually adopted in traffic assignment. For the purpose of more precise description of traffic pattern, we have to estimate the parameters of VDF in advance. This paper presents a methodology for estimating the parameters, which combined with golden section method. By using the method we have estimated the parameters with real data based on KTDB(2006), and validated them. Compared to the existing values of the parameters, newly estimated values are found to be closer to real world.

• Tunnel and Underground Space
• /
• v.26 no.2
• /
• pp.100-109
• /
• 2016

This study suggests three spatial distribution functions of strength parameters, which can be adopted in the derivation of failure conditions for transversely isotropic rocks. All three proposed functions, which are the oblate spheroidal function, the exponential function, and the function based on the directional projection of the strength parameter tensor, consist of two model parameters. With assumption that the cohesion and friction angle can be described by the proposed distribution functions, the transversely isotropic Mohr-Coulomb criterion is formulated and used as a failure condition in the simulation of the conventional triaxial tests. The simulation results confirm that the failure criteria incorporating the proposed distribution functions could reproduce the general trend in the variations of the axial stress at failure and the directions of failure planes with varying inclination of the weankness planes and confining pressure. Among three distribution functions, the function based on the directional projection of the strength parameter tensor yields the highest axial strength, while the axial strength estimated by the oblate spheroidal distribution function is the lowest.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.5
• /
• pp.125-130
• /
• 2009

Storage function method which considers the non-linearity of the relationship between rainfall and runoff has been frequently used to predict runoff in a basin and a flood pattern. However, it is time-consuming to estimate appropriate parameters of every basin and rainfall event, which requires the empirical parameter equation applicable in Korea. In this study, multiple regression analysis is used to develop empirical equations to estimate parameters of Storage Function method using basin characteristics. The basin area, maximum stream length, and stream slope are considered as the basin characteristics as the result of the regression analysis. Collinearity is removed and trial-and-error method is used to choose the most descriptive parameters to the dependent variables in Han River basin which is divided into 30 subbasins. The developed equations are validated using the rainfall events in MunMak gauging station and named as 'Han River equation'. The equation could provide the useful information about Storage Function method parameter to calculate runoff from a basin and predict river stage.

• Geomechanics and Engineering
• /
• v.30 no.4
• /
• pp.325-336
• /
• 2022

This paper analyzes the ground surface settlements induced by side-by-side twin shield tunnels bored in sedimentary soils, which primarily consist of sand with clay strata above the tunnel crown. The measurements were obtained during the construction of twin tunnels underneath the Incheon International Airport (IIA) located in Korea. The measured surface settlement troughs are approximated with Gaussian functions. The trough width parameters i and K of the settlement troughs produced by the first and second tunnel passings are determined, along with those for the total settlement trough. The surface settlement troughs produced by the first shield passing are reasonably represented by a symmetric Gaussian curve. The surface settlement troughs induced by the second shield tunnel display marginal asymmetric shapes at selected sections. The total settlement troughs are fitted both with a shifted symmetric Gaussian function and the superposition method utilizing an asymmetric function for the incremental trough produced by the second tunnel. It is revealed that the superposition method does not always produce better fits with the total settlement. Instead, the shifted symmetric Gaussian function is overall demonstrated to provide more favorable agreements with the recordings. Therefore, the shifted symmetric Gaussian function is recommended to be used in the design for the prediction of the settlement in clays caused by twin tunneling considering the simplicity of the procedure compared with the superposition method. The amount of increase in the width parameter K for the twin tunnel relative to that for the single tunnel is quantified, which can be used for a preliminary estimate of the surface settlement in clay induced by twin shield tunnels.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.2
• /
• pp.226-232
• /
• 2006

This paper presents the parameter measurement methods for high performance drive of induction motors, which are suitable for the self-commissioning function of commercial inverters. In this study, some factors that affect the accuracy of parameter measurement are examined. Measuring methods and conditions that are best fit to each parameter measurement procedure are then proposed. All the measurement procedures can be done without any auxiliary equipment, so that those can be easily adopted as self-commissioning functions of commercial inverters. To improve the measuring accuracy, least square approximation methods are adopted during the measurement procedure. The validity of the proposed methods are confirmed through experiments.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.195-202
• /
• 1994

In this research, a lot of triaxial test results (CID) are analyzed to study the curvature characteristics of failure envelope of sand and parametric relationship between shear strength and state parameter by Been and Jefferies. In the conventional triaxial tests, correction for the change of sectional area of a sample and for membrane influence is essential especially in order to determine critical state (or steady state) condition more correctly. Based on the test results, a model to express the shear strength of fine sand as a function of density and stress level is presented and curvature characteristics of shear failure envelope and parametric relationship between state parameter and shear strength parameters are evaluated.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.54 no.3
• /
• pp.122-132
• /
• 2005

This paper presents a novel approach based on Prony method to analysis of small signal stability in power system. Prony method is a valuable tool in identifying transfer function and estimating the modal parameter of power system oscillation from measured or computed discrete time signal. This paper define the relative residue of time signal and propose the condition to select low frequency oscillation in each generator. This paper describes the application results of proposed algorithm with respect to KEPCO systems. Simulation results show that the proposed algorithm can be used as another tools of power systems analysis.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.173-176
• /
• 1996

This paper deals with the problem of designing an adaptive regulator in order to improve transient performance in time-response when the linear state-space model of the plant contains unknown parameters which vary within prescribed bounds. The whole possible parameter space is divided into some subspaces and multiple models and controllers are established from the view point that each controller gives satisfactory transient behavior for systems corresponding to each parameter subspace. Based on time-response and an associated cost function, an appropriate controller is selected on-line out of multiple controllers.