• Journal of Navigation and Port Research
• /
• v.34 no.7
• /
• pp.543-552
• /
• 2010

Modified compact combline bandpass filters are proposed based on the miniaturized quarter-wave transmission line which is composed of the parallel coupled line and lumped capacitors. The electrical length of the parallel coupled line in a resonator, which determines the size of combline bandpass filters, is just $5^{\circ}$ or $7^{\circ}$, resulting in a compact circuit area. The designed combline bandpass filter also has a wide upper stopband by suppressing the spurious passbands, not moving. Measured results of two fabricated filters centered at 400MHz show good agreement with the theoretical predications.

• Journal of Korea Multimedia Society
• /
• v.6 no.2
• /
• pp.224-229
• /
• 2003

In this paper, an effective skeleton method is proposed in order to obtain an enhanced digital image of skeleton line. The edge-detection method is applied in the preprocessing stage and after that, the modified Parallel method is applied to obtain the improved image of skeleton line. The existing parallel methods are Zhang, Lu and Wang, and Paul methods. Firstly, a parallel process method Is applied, and the proposed method is applied that the original is compared with the four neighbor pixels and four corner pixels of mask. In conclusion, the proposed method shows an improved connectivity and quality of skeleton line.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.4
• /
• pp.369-378
• /
• 1992

This paper proposes a utility parallel processing inverter system, which consists of a voltage source PWM inverter, isolation transformer and a reactor linking the inverter to utility line. This system realizes following functions : (1) voltage phase frequency and amplitude synchronization between inverter and utility line at stand-alone mode. (2) current phase synchronization between inverter and load at parallel mode. Therefore, despite sudden increase in load current over setting point at stand-alone mode, inverter system can be transferred into parallel mode immediately without transient current. Furthermore, high frequency(18KHz) PWM control and sinusoidal filtering improve the inverter output waveform by eliminating high order harmonic components as well as low order. As a switching device, IGBT is used for high frequency switching and large current capacity.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.585-592
• /
• 2003

The parallel operation system of UPS is used to increase reliability of power source at critical load. But parallel UPS system has a few defects, impedance is different from each other and circulating current occurs between UPSs, due to line impedance and parameter variation, though controlled by the same synchronization signal. According to such characteristic of parallel UPS, balanced load-sharing control is the most important technique in parallel UPS operation. In this paper, a novel power deviation compensation algorithm is proposed. it is composed of voltage controller to compensate power deviation that be calculated by using active and reactive current deviation between Inverters on synchronous d-q reference frame.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.1
• /
• pp.81-90
• /
• 2015

This paper investigates the droop control-based real and reactive power load sharing with a virtual inductor when the line impedance between inverter and Point of Common Coupling (PCC) is partly and unequally resistive in high-capacity systems. In this paper, the virtual inductor method is applied to parallel inverter systems with resistive and inductive line impedance. Reactive power sharing error has been improved by applying droop control after considering each line impedance voltage drop. However, in high capacity parallel systems with large output current, the reference output voltage, which is the output of droop controller, becomes lower than the rated value because of the high voltage drop from virtual inductance. Hence, line impedance voltage drop has been added to the droop equation so that parallel inverters operate within the range of rated output voltage. Additionally, the virtual inductor value has been selected via small signal modeling to analyze stability in transient conditions. Finally, the proposed droop method has been verified by MATLAB and PSIM simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.40-45
• /
• 2008

In this paper, the exact analysis of the parallel coupled line with open stub and an application to branch-line hybrid are presented. The Z-parameter of the parallel coupled line with an open stub is derived. The structure shows the characteristics as a lowpass filter unit cell(LUC) with wide stop band. Using the characteristics we designed a miniaturized branch-line hybrid with wide harmonic-suppressed band. The size of the new branch-line hybrid is a half of the conventional branch-line hybrid. The frequency response is the same with that of the conventional one near 1.7 GHz center frequency. Including the fifth harmonics, up to 12 GHz spurious responses are suppressed below to -20dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.9B
• /
• pp.1668-1675
• /
• 1999

In this thesis, a narrowband bandpass filter using HTS is proposed for the multiplexer of the satellite communication subsystems. The proposed structure using HTS provides the narrower band and the lower insertion loss characteristics than the conventional parallel-coupled-line bandpass filter. The filter structure using hairpin-line only cause the spurious modes due to the surface waves. But these modes can be lessened by using the hybrid hairpin-line/parallel-coupled-line proposed in this thesis. The narrowband bandpass filters using HTS at the operation frequency of 14.25 GHz are fabricated to have the narrow bandwidth less 1% and the insertion loss less 3dB in comparison with the normal metal microstrip filter with the same three poles. The experimental results show that the filter using HTS has the characteristics of the narrower bandwidth and less insertion loss and can be fabricated with more compact size in comparison with the bandpass filter using normal metal.

• Journal of Korea Multimedia Society
• /
• v.7 no.4
• /
• pp.459-466
• /
• 2004

In this paper, an effective skeleton method is proposed in order to obtain an enhanced digital image of skeleton line. The binary image using the threshold values is applied in the preprocessing stage and then the modified parallel processing method is applied to obtain the improved image of skeleton line. The existing skeleton methods are Rutovitz, Steiabelli and other five skeleton methods. In the digital process of skeleton line, the major problem caused by these methods is elongated lines and noise branches of the processed image. In this study, however, such noises are deleted first by the modified parallel processing step of the proposed method. Then a pixel is compared to its eight neighbor pixels. if its neighbor pixels are in one of the eight conditions, the central pixel is deleted. As a result, the quality of the skeleton is better then those produced by the existing skeleton methods.

• Journal of Korea Multimedia Society
• /
• v.18 no.10
• /
• pp.1180-1188
• /
• 2015

In this paper, a parallel cell contour line extraction algorithm using CUDA, which has no inner contour lines, is proposed. The contour of a cell is very important in a cell image analysis. It could be obtained by a conventional serial contour tracing algorithm or parallel morphology operation. However, the cell image has various damages in acquisition or dyeing process. They could be turn into several inner contours, which make a cell image analysis difficult. The proposed algorithm introduces a min-max coordinates table into each CUDA thread block, and removes the inner contour in parallel. It is 4.1 to 7.6 times faster than a conventional serial contour tracing algorithm.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.153-156
• /
• 2002

In this paper, we have designed a small size lumped/distributed hybrid element directional coupler using parallel coupled-line theory. a hybrid lumped equivalent circuit for a conventional parallel directional coupler is proposed. The equivalent circuit and design formula for the presented lumped element coupler are derived based on the even- and odd-mode properties of a parallel-coupled line. By using the derived design formula, we have extracted design parameters and designed the 3㏈ and 10㏈ small size lumped element directional couplers at the center frequency of 2Ghz. Excellent agreements between design theory and simulation on the designed directional couplers show the validity of this paper.