• 펄프종이기술
• /
• 제42권2호
• /
• pp.41-45
• /
• 2010

This study was performed to evaluate the effect of paper property changes by internal addition of surface strength agent on printability. Advances in printing technique has required the development of paper qualities in many aspects. Basically paper structure is composed of hydrogen bonds which induce many problems in high speed printing machine because of weak bonding strength. One of the important printing problems is surface picking when mechanical pulp or recycled pulp are used. It was caused by the ink-stained blanket in printing process because accumulations of pollutant in white water and other elements which are bonded weakly or do not have hydrogen bonds. Debris at paper surface adheres to blanket which deteriorates printing efficiency and causes various problems. To complement these problems, Pennocel 5137 of polysaccharide structure was used as an agent to improve paper's surface property, strength and printability. Paper surface picking was analyzed by RI-1 test. As the dosage amount increased tensile strength, fiber bonding strength and ZDT strength were improved. Further more formation, smoothness and surface picking resistance were improved. It was confirmed that when adding polysaccharide structure polymers to improve surface strength such as surface picking resistance, it was also possible to improve tensile strength, fiber bonding strength, formation and smoothness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.697-703
• /
• 1996

Fatigue strength of high strengthsteels are variable with many different surface treatment. It is well known that residual compressive stress retard fatigue crack growth rate(or arrest crack). High strngth steels are manufactured by following process. Heat treatment, shot peening and chromium plating process. High strength steel(HRC40 or above) which are subjected to fatigue load and dynamic load, chromium plated parts shall be peened in accordance with requirements and baked after plating. The purpose of this paper is to compare and discuss the influence of surface treatment and hydrogen embrittlement on fatigue strength of high strength steel. Therefore, fatigue test was performed to investigate influence of surface treatment. The results shows that shot peening is very effect method in creasing fatigue life and after plating, baking process is essential to prevent hydogen failure. In this paper, the experimental investigation is made to clarify the influence of shot peening conditions and baking process on fatigue strength of high strength steel.

• 폴리머
• /
• 제37권2호
• /
• pp.196-203
• /
• 2013

Surface modification of meta-aramid fibers was performed by phosphoric acid treatment. Surface morphology and element composition of untreated and treated fibers were analyzed by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). Effects of surface modification on the mechanical strength of aramid papers made from meta-aramid fibers and fibrid were investigated. Surface modification conditions were optimized by response surface analysis (RSA). Results show that phosphoric acid treatment increases the surface roughness and oxygen content of aramid fibers. They improve the interface bonding strength between aramid fibers and fibrid, which improves the tensile strength of aramid papers. The results of response surface analysis indicate that the tensile strength of aramid papers increases by 47.5% and reaches the maximum when meta-aramid fibers are treated with 21.1wt% phosphoric acid solution at $39.3^{\circ}C$ for 36.7 min.

• 한국인쇄학회지
• /
• 제22권2호
• /
• pp.101-110
• /
• 2004

The local surface strength variation of coated papers were measured at various speeds on a number of coated paper samples to study the effects of speed and ink tack on coating pick. Coating pick phenomenon is observed in an ink transfer variation curve as a decrease in the slope of the curve. On the other hand, it causes an actual decrease in net ink transfer to paper with an increase in speed. The effect of speed on coating pick depends on ink tack, ink film thickness and surface properties of coating layer formation of paper. A novel device to measure the surface strength can rate the coating paper in a different order. Comparison are made between dry test of coating paper pick and wet coating pick test of printing in IGT printability tester. Coating formulation is the main key to prevent from coating pick. The binder level increases, the coating pick and the slop decrease. The piling on blanket in printing is a problem when the coating pick is occur on a local area rather than average surface strength of coated papers.

• 펄프종이기술
• /
• 제37권2호
• /
• pp.70-77
• /
• 2005

For the purpose of developing liner board for water resistant corrugated board in the cold chain system, several types of base paper for corrugated board were purchased from the market and 6 different boards were produced in the mill by applying the chemicals, chosen in the previous studies, on the base paper. Then water-moisture resistance and physical properties of the boards were compared each other. The liner board which is dried at high temperature with pressure by Condebelt (CK paper) showed a superior performance in strength over common liner boards. Strength of the board increased by surface chemical treatment up to $60\%$ of compressive strength and $30\%$ of burst strength. Starch insolubilization with Ammonium Zirconium Carbonate and surface coating with a surface sizing agent and a moisture resistant chemical on CK paper showed the best result. Therefore this method was recommended to produce the outer liner board for water resistant corrugated board.

• 펄프종이기술
• /
• 제45권4호
• /
• pp.1-8
• /
• 2013

High loading of printing and writing grades with fillers has many advantageous aspects in papermaking because it allows decreasing fiber use and reducing manufacturing cost. High loading technology, however, has some disadvantageous aspects as well. It decreases physical properties of papers, especially strength properties. The problem associated with high loading can be reduced by applying surface sizing starch solution onto paper surface. It is important to control the penetration of the surface sizing starch solution into paper web to obtain the desired property improvement. In this study, the effect of the addition of two polymers into starch solution on paper properties has been examined. PVOH and polyDADMAC were used as polymeric additives for surface sizing with oxidized starch. Viscosity of starch solutions and surface roughness of dried starch films on glass slides showed that some interactions between polymeric additives and oxidized starch have been occurred and the most extensive interaction with starch solution was obtained with high molecular weight polyDADMAC. Low molecular weight PVOH was most effective in improving folding endurance and internal bond strength. On the other hand, polymer addition showed no effect on surface strength of paper. This indicates that not the level of starch holdout but the bonding strength of starch itself has predominant influence on surface strength of paper.

• 펄프종이기술
• /
• 제40권3호
• /
• pp.9-14
• /
• 2008

Agar-agar extracted from red algae was used as a surface sizing material for paper after filtering, bleaching, and viscosity adjustment by oxidative depolymerization. Oxidized starches from corn and tapioca were compared to agar-based surface size in the respects of paper surface modification, strength improvement, and printability. Agar-based surface size showed high strength improvement and good printability as much as starch-based ones except film forming ability, which may be improved by adding additives, and demonstrated its great potential to be used as inexpensive and high quality surface size in future.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.78-81
• /
• 2004

In this paper, the effect of adhesion properties of semiconductive-insulating interface layer of silicone rubber on electrical properties was investigated. Surface structure and adhesion of semiconductive silicon rubber by surface asperity was obtained from SEM and T-peel test. In addition, ac breakdown test was carried out for elucidating the change of electrical property by roughness treatment. From the results, Adhesive strength of semiconductive-insulation interface was increased with surface asperity. Dielectric breakdown strength by surface asperity decreased than initial Specimen, but increased from Sand Paper #1200. According to the adhesional strength data unevenness and void formed on the silicone rubber interface expand the surface area and result in improvement of adhesion. Before treatment Sand Paper #1200, dielectric breakdown strength was decreased by unevenness and void which are causing to have electric field mitigation small. After the treatment, the effect of adhesion increased dielectric breakdown strength. It is found that ac dielectric breakdown strength was increased with improving the adhesion between the semiconductive and insulating interface.

• 펄프종이기술
• /
• 제30권3호
• /
• pp.63-72
• /
• 1998

This research was intended to evaluate the effect of carboxymethylcellulose(CMC) on the coating structure and surface strength of coated paper prepared with amphoteric latex based coating color. Printability and optical properties of coated papers were compared. The influence of the consolidation behavior of coating color on the coating structure and the surface strength of coated paper was investigated. Compared with the conventional anionic latex, amphoteric latex formed bulkyer, smoother and more porous coating layer, which in turn, restricted binder migration in the coating layers, and facilitated immobilization of coating colors. However, dry pick strength of coated paper was decreased. The addition of CMC to these systems had strongly influenced on. the consolidation behavior and porosity in the dry state, through forming the network structure of coating layers by the interaction with amphoteric latex particles. Thus, printability and optical properties of coated papers were improved. Results indicated that amphoteric latex could be practically applied to the paper coating to improve printability and optical properties of coated papers.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.131-136
• /
• 2000

This paper is concerned with the surface roughness and the bending strength of ground workpiece in ZrO2 ceramic grinding. Surface roughness was measured with surface tracer and bending strength value was obtained by three-point bending test on machining center using tool dynamometer. Grinding experiments were carried out to examine the effects of grinding conditions including diamond mesh size, table speed, and depth of cut on ground surface roughness. The correlation between surface roughness and bending strength was also inspected. The experimental results indicate that the rougher surface is produced as the mesh size of diamond wheel is reduced and table speed is increased, but surface roughness is not affected by depth of cut. The values of bending strength decrease as the values of Ra, Rmax and Ku increase.